Varathane Var-01 Oil-based Polyurethane User Manual

varathane var-01 oil-based polyurethane

DESCRIPTION AND USES

Varathane® Interior Oil-based Polyurethane is an oil-modified polyurethane designed to provide abrasion and scratch resistance to stained wood surfaces. This product is ideal for application to all interior projects such as furniture, doors, cabinets and trim. It is NOT recommended for floors, linoleum, vinyl or glazed tiles and metal.

PRODUCTS

PRODUCT APPLICATION

SURFACE PREPARATION
Previously Finished Surfaces – To ensure proper adhesion, surfaces must be clean, dry, and free of wax, grease, oil, shellac, lacquer, mildew, and polishes. Remove wax with a wax stripper, shellac with a paint stripper, and mildew with a solution of 10% household bleach and water. Old finishes in poor condition should be removed. Sand using 150-220 grit sandpaper to obtain a smooth surface. Remove all sanding dust using a vacuum, tack cloth, or cloth dampened with mineral spirits. Unfinished Surfaces – Sand using 150-220 grit sandpaper and remove all sanding dust using a vacuum, tack cloth, or rag dampened with mineral spirits. If a filler or putty is used, make sure it does not contain wax allow enough time for it to dry thoroughly. Stained or Painted Wood – Follow manufacturer’s directions for application of the stain or paint. Make certain the surface is thoroughly dry before applying Varathane Oil-Based Polyurethane. Using this polyurethane over white or lightly painted surfaces could cause discoloration. Refer to the manufacturer’s label for dry times. For best results, use Varathane Premium Wood Stains.

WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

APPLICATION
Do not apply in direct sunlight. Use in an area with adequate ventilation such as an open garage. Use only when air (ambient) temperature is between 55-90°F (13-32°C) and relative humidity is below 85%. Lower temperatures and/or high humidity may cause slower dry times and slower dry may also result from applications on redwood, cedar or woods with high oil content, or when applied over some stains. Use full strength. Do not thin. Stir thoroughly before and during use. To prevent bubbles in the finish,

DO NOT SHAKE. Apply using a good quality natural bristle brush or applicator. Allow the finish to dry 8 hours before re-coating. Re-coat only when previous coats have dried clear and feel hard. The coating should no longer feel tacky to the touch. If any coat has dried more than 12 hours, lightly sand before applying another coat. A minimum of two coats is recommended. Allow the finish to dry 24 hours before light use. Wait 3 days before subjecting the surface to normal usage.

DRY AND RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative humidity. Allow more time at cooler temperatures. Dries to the touch in 1-2 hours and can be recoated in 4 hours. It is fully cured in 72 hours.

CLEAN UP
Clean application tools and equipment with mineral spirits or paint thinner.

TECHNICAL DATA

PHYSICAL PROPERTIES

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice