Ciro G0120301 Dryforce Quick Release Waterproof Cooler For H-d Luggage Rack User Manual

G0120301 Dryforce Quick Release Waterproof Cooler for H-D Luggage Rack

Product Information

The Ciro product is a Quick Release Waterproof Cooler designed
to be mounted on a motorcycle’s luggage rack. It is easy to
assemble and install, but it is recommended to have a competent
mechanic install the product using standard mechanical procedures
to ensure a safe and successful installation. The weight of the
contents placed in the bag should not exceed safe limits, and it is
the user’s responsibility to determine what the safe limit is based
on the position of the bag, proper securing of the bag, and the
weight limits given for the motorcycle by its manufacturer. The bag
comes with securing straps that need to be fastened and tightened
properly before riding the motorcycle to prevent potential serious
injury or death.

Product Usage Instructions

1. Park the motorcycle on a level surface and allow it to
   cool.
2. Check the spacing of the mounts prior to installation. The
   hooks should be 4-4.5 inches apart, and the latches should be 5-6
   inches apart. The spacing may vary by application.
3. Unbuckle and slacken the securing straps on both sides of the
   bag.
4. Set the bag onto the luggage rack, hold the bag parallel to the
   luggage rack when setting it down. Do not tip the bag to either
   side when setting it down as it can cause contact with the top of
   the Tour-Pak lid.
5. Lift the bag slightly to loop both of the securing straps to
   the outermost rungs of the luggage rack. Do not buckle them at this
   time.
6. Make sure that the hooks and latches will capture the luggage
   rack when the bag is slid over.
7. With a smooth, firm motion, slide the bag to the left to secure
   the bag to the luggage rack. The hooks should slide under the
   luggage rack rung, and the latches should capture the luggage rack
   rung with an audible latching sound.
8. Fasten the securing straps on both sides of the bag, capturing
   the release cord on the right side. Pre-load the straps by applying
   light downward force while the straps are tightened.
9. To release the bag, unbuckle both securing straps and pull the
   release cord away from the bag.

It is important to follow the included mounting suggestions and
choose additional tie-down straps that work for your application.
Adhere to the vehicle manufacturer’s GAWR and GVWR (gross axle
weight rating and gross vehicle weight rating) when attaching
luggage to a vehicle. Added weight, shifting loads, and improperly
attached luggage can result in loss of control and can lead to
serious injury or death. Always ensure that the bag is fastened and
straps are secure before riding the motorcycle to prevent potential
serious injury.

Dryforce TMQuick Release Waterproof Cooler for H-D®Luggage Rack

WARNING This indication alerts you to the fact that ignoring the contents described herein can result in potential serious injury or death if not followed. CAUTION This indication alerts you to the fact that ignoring the contents described herein can or will result in material damage and/or personal injury. ATTENTION This indication alerts you to the fact if you ignore this detail you will affect the performance or functionality of the product.

All Ciro products are designed for “easy assembly” and/or “plug and play”. We recommend a competent mechanic install our products, using standard mechanical procedures to assure a safe and successful installation. Read completely and understand the instructions prior to starting installation.
NOTE: Ciro products are designed and manufactured under very strict quality control. Ciro warrants that products sold to the original purchaser shall be free from any defects in materials and workmanship for a period of 3 (three) years from the date of purchase, and a limited lifetime warranty against LED failure. Ciro will have no obligation if the customer cannot show proof of purchase. Warranty will not be granted unless the part is properly installed and maintained. Ciro will not be liable for any consequential and incidental damages, including labor, or non-Ciro products. Please visit Ciro3d.com for our complete warranty policy.

CAUTION

Fig.1

Ciro is not responsible for improper loads or unsafe positioning of the Quick

Release Waterproof Cooler. Be sure the weight of the contents placed in the

bag do not exceed safe limits. It is the user’s responsibility to determine what

the safe limit is based on the position of the bag, proper securing of the bag

and the weight limits given for the motorcycle by its manufacturer.

WARNING
It is the end user’s responsibility to use good judgment. Follow the included mounting suggestions. Choose additional tie down straps that work for your application. Adhere to the vehicle manufacturer’s GAWR and GVWR (gross axle weight rating and gross vehicle weight rating) when attaching luggage to a vehicle. Added weight, shifting loads, and improperly attached luggage can result in loss of control and can lead to serious injury or death.

WARNING Prevent potential serious injury. Ensure the bag is fastened and straps are secure before riding the motorcycle.

Fig.2

Mounting Instructions:
1. Park on a level surface, allow the vehicle to cool.
2. Check the spacing of the mounts prior to installation. The hooks should be 4-4.5″ apart, the latches should be 5-6″ apart, Fig.1. Spacing may vary by application.
3. Unbuckle and slacken the securing straps on both sides of the bag, Fig.2.
4. Set the bag onto the luggage rack, hold the bag parallel to the luggage rack when setting it down. DO NOT tip the bag to either side when setting it down. Fig.3.
CAUTION
Bringing the bag down at an angle can cause contact with the top of the Tour-Pak lid. Fig.4.
5. Lift the bag slightly to loop both of the securing straps to the outermost rungs of the luggage rack, Fig.5. Do not buckle them at this time.
6. Make sure that the hooks and latches will capture the luggage rack when the bag is slid over.
7. With a smooth, firm motion, slide the bag to the left to secure the bag to the luggage rack, Fig.6. The hooks should slide under the luggage rack rung and the latchs should capture the luggage rack rung with an audible latching sound. Illustrated in Fig.1.
8. Fasten the securing straps on both sides of the bag, capturing the release cord on the right side, Fig.7. Pre-load the straps by applying light downward force while the straps are tightened.
Note: To release the bag, unbuckle both securing straps and pull the release cord away from the bag, Fig.8.

Fig.3

G0120301, REV._ For the latest version of installation instructions visit www.ciro3d.com

Page 1 of 2

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

ATTENTION
Verify that the bag is securely attached before operating the motorcycle. Secure all straps away from painted surfaces, moving parts, pinch points or hot items. Check the straps before each ride and at each stop. Bag contents may shift during operation which can result in loose straps. Roll up any excess length in all of the straps and secure it.

G0120301, REV._ For the latest version of installation instructions visit www.ciro3d.com

Page 2 of 2

References

• Ciro3D: Motorcycle Accessories & Parts
• Ciro3D: Motorcycle Accessories & Parts