Contents hide

2 Product Information: RevoLine VariEco NHK

2.1.1 General Safety Instructions

2.1.2 Assembly Instructions

2.1.3 Adjustment of End Positions

2.1.4 Electrical Connection

2.1.5 Troubleshooting

2.1.6 Documents / Resources

2.1.6.1 References

13 109.6401 RevoLine VariEco NHK

Product Information: RevoLine VariEco NHK

The RevoLine VariEco NHK is a tubular drive used to open and
close blinds. It comes with an emergency unlocking device that can
be used in case of emergencies like blackouts or defects to the
tubular drive. The device is not intended to be used on a regular
basis as it may cause damage to the tubular drive. The product is
compliant with European directives 2006/42/EG and a declaration of
conformity is available at www.elero.com/downloads-service/.

Product Usage Instructions:

General Safety Instructions

Always use the setting tool or Phillips/hexagon socket tool to
activate the limit switch setting screws. Never use an electric
screwdriver.
Do not connect several drives in parallel due to feedback
voltage from the installed capacitor.
Motor controls in UP/DOWN direction must be interlocked with
one another.
A reversing delay of at least 0.5 sec. must be ensured.
Entrapment and crushing hazards may occur during operation.
Open or close the blind slowly using the emergency crank handle in
case of emergencies.

Assembly Instructions

Follow the assembly instructions provided in the user manual to
assemble the RevoLine VariEco NHK.

Adjustment of End Positions

For upper end position adjustment, allow the drive (without
blind) to run fully in the DOWN direction.
Attach the rolled-down blind to the shaft.
Push the [OPEN] button and keep it held down.
Using the setting tool, turn the limit switch setting screw in
positive or negative direction until you reach your desired upper
end position.
For lower end position adjustment, push the [DOWN] button and
keep it held down.
Using the adjusting key, turn the DOWN limit switch setting
screw in positive or negative direction until you reach your
desired lower end position.

Electrical Connection

Ensure that the motor controls in UP/DOWN direction are
interlocked with one another.
Ensure a reversing delay of at least 0.5 sec.
Follow the electrical connection instructions provided in the
user manual to connect the RevoLine VariEco NHK to power grid
230V/50Hz PE N L.

Troubleshooting

If malfunctions occur or the device has been damaged despite
proper handling, please contact your contractor or dealer.

View Fullscreen

RevoLine VariEco NHK Assembly instructions

General
Application: Tubular drive for small rolling doors, roller shutters and textile sun protection Limit stop: Mechanical Special feature: Emergency manual operation, noiseless soft brake (up to 20 Nm) Shaft size: Type M from Ø 50 mm, type L from Ø 63 mm Standard scope of delivery · 2 m connecting cable, assembly instructions Accessories · Adapter sets, motor bearing, control units

Safety instructions

&$87,21

General safety instructions for use including installation of drives for roller shutters, awnings and textile sun protection can be found in the “Safety instructions” leaflet supplied with each drive. Please read the general safety instructions and this installation manual carefully as the procedure in this manual is a prerequisite for correct use of the product. Any intervention by unqualified personnel or failure to comply with warnings may lead to personal injuries or material damage. Figures included are for illustration purposes only. The illustrations may differ from your product with respect to minor details and are provided for general information only. elero GmbH continuously strives to improve all products. As a result, the specifications, features and technology of this product may be changed at any time. The information provided is based on current information at the time of publication. No claims can be derived from the technical data, images and information provided in this manual.

Assembly
· Only connect the drive with the power turned off. · Only insert the drive’s plug with the power turned off. · The drive is only capable of operation while installed. · Never adjust the end position to a mechanical stop. · The length of the winding shaft is determined for each
specific installation depending on the drive head and motor bearing used at the installation site. · Do not drill holes in the area of the tubular drive. Installation in profile tubes · Push drive with the suitable drive adapter and limit switch crown into the profile tube. Install the shaft with drive and counterpart support so that the limit switch setting mechanism is accessible. · Secure the counterpart support to prevent axial movement (screw on the idler or rivet it on). · Connect the drive to the elero assembly cable, matching up the core colours. · Allow the drive to run in DOWN direction until the limit switch cuts out. · Attach the blind to the shaft. Installation in round tubes · On the round tube, cut a slot in the end of the tube on the drive side. · Push the drive in so that the lug of the drive engages in the slot. · Screw in the drive adapter or rivet it. · Allow the drive to run in DOWN direction until the limit switch cuts out. · Attach the blind to the shaft.

Adjustment of end positions
UP
DOWN DOWN

UP
DOWN DOWN

UP DOWN

DOWN Adjusting key: Artikel-Nr. 13 109.6401

DOWN

NOTE: For activation of the limit switch setting screws, use the setting tool or Phillips/hexagon socket tool. Never use an electric screwdriver!
Important: The limit switch setting screws for the upper end position and lower end position are assigned depending on the parallelism of the rotating limit switch crown with the running direction arrow.
Upper end position 1. Allow the drive (without blind) to run fully in DOWN direction. 2. Attach the rolled-down blind to the shaft. 3. Push the [OPEN ] button and keep this held down. 4. Using the setting tool, turn the limit switch setting screw in posi-
tive or negative direction until you reach your desired upper end position.
Lower end position 5. Push the [DOWN ] button and keep this held down. 6. Using the adjusting key, turn the DOWN limit switch setting
screw in positive or negative direction until you reach your desired lower end position.
Checking the end positions Allow the drive to run into the relevant end position until the limit switch cuts out. The electric cut-out must take place before the blind has reached the end position of its mechanical travel path. If the blind is constantly operated as far as its end position, there is a risk of damage to the drive and/or blind or even a danger it will be destroyed. Take into account any possible changes to the length of the blind due to temperature fluctuations or weather influences. Allow for a safety margin.

13 816 4001_EN_0822

RevoLine VariEco NHK Assembly instructions

Electrical connection
Note: Due to feedback voltage from the installed capacitor, never connect several drives in parallel. The motor controls in UP/DOWN direction must be interlocked with one another. A reversing delay of at least 0.5 sec. must be ensured.
M 1~

green/Yellow blue black brown

junction box

102
power grid 230V/50Hz PE N L

Notes on troubleshooting

Fault
· The drive doesM not switch off in1~ the end position via the limit switches
· Drive does not react
· Dsrciavtoeladdoi es not redearicvtatione

verde/giallo

blu

nero

marrone

Cause · Limit switch
crown is not being driven
91,5 74
· Incorrect connection

100

Remedy
· Readju2s312t90i0n01 stallation and1 limit switches via the limit switch adjustment screws
· Set limit switch
· Readjust connection
LK 60

O 45

Emergency crank handle
Note: Tubular drive versions with the additional code NHK are fitted with an emergency unlocking device. The emergency unlocking device ensures that the blind can be opened or closed in case of an emergency. Examples of emergencies might be blackouts or a defect to the tubular drive. The emergency unlocking device is not intended to be used on regular basis as otherwise the tubular drive may become damaged.

Emergency release of the tubular drive via the manual

override/emergency crank handle

CAUTION

· Hands, loose items of clothing or long hair may become

entrapped and crushed.

· Disconnect the tubular drive from the mains power prior to

emergency unlocking (switch should not be operated).

· Attach the manual override/emergency crank handle to the

tubular drive.

Open or close the blind slowly emergency crank handle.

turLnaiunfgflätchhee

mmuaßnmuitalPDo1vgeerfreitdteet/

werden./

· Ensure that you do not go past theBleimariintgsswuriftaccheehsassteo tb.e lubricated whith PD1

EU Conformity

elero hereby declares that this product is in compliance with the essential requirements and other relevant provisions of European directives 2006/42/EG that are applicable in Europe. A declaration of conformity is available at the website www.elero.com/downloads-service/

233941201 1
Manufacturer’s address
elero GmbH 73278 Schlierbach GERMANY www.elero.de

Service 677

138066003 1

If malfunction62s9 have occurred or the

device has been damaged despitSechrauben mit 4,3u0,3 Nm anz

proper handling, please contact your

contractor or dealer.

Tighten the screws whith 4,3u

102
rete 230V/50Hz PE N L

Drehmoment nach Arbeitsanweisung./ Torque according to work instruction. d

101013621 2

ø 12.5 x 18.5 tief

1330912fw10o2irthfrøoa n1t 2elbeomltesnts

101014701 4

Drehmoment nach Arbeitsanweisung./ d
Torque according to work instruction.

Connecting cable pluggable

Excelstückliste

front element

wall anchors Menge 13 106.3501 1
1
1
1

Mengeneinheit Dokumentnummer 7 mm 6-eTditegl e

STK

233941201

wMiotthor MaHw90 Fnl ing loop

STK

231620002

23Ends7ch7alt1er.k0pl.060F 2

STK

wa23l1l290a00n1 chorsGetriebe

13 301.0801

STK

138200001

Sicherheitshinweis

Material

Kommentar

Gelenklager für Kupplungstrichter 23 772.0002 Knick-Kurbel mit Gelenklager und 7 mm 6-kant 23 764.0002 Gelenklager mit Markisenöse 23 731.0002
–

STK

138164001

Einstellanleitung

Technical

data1

anSTK d

dimensions 138066003

Aufkleber Typenschild

–

138037103

Transferfolie 110×450 lfm.TMX Super Pr.

The technical data specified is suCbAB ject to tolerance factors

(according to ap1 plicSTKable s13t3a092n102dardMsot)or.rohr 595

Präz. St-Rohr 45 x 1,5 DIN 2393

All illustrations ar4e noSTKn-bind10i1n014g701.

Senkschraube EJOT Altracs Plus 4×10 Torx 20

St verzinkt

2 STK

101013621

Schraube WN 1552 – DG35x7
C

St verzinkt

EJOT Nr.:441 0383 801

100 90
30°

Rear cable outlet Kanten gebrochen
Edges broken

Diese Maße werden besonders ge This dimensions are particularly

Gemäß RoHS-Richtlinie 2011/65 EG / according to RoHS directive 2

—

–

—

–

—

–

—

–

—

–

d Drehmomentangaben hinzu gekommen.

30.10.2018

c MiniPlug entfernt

06.12.17

b Typenschild geä.

24.10.17

a Rohrindex erhöht, Schraube war 101010907.

20.06.2017

Index:

Kurzbeschreibung / Short Comment:

Datum / Date

F O 60
q 16
74 91,5

E= 26 2 | EN

RevoLine VariEco NHK Assembly instructions

Technical data and dimensions: VariEco M NHK / VariEco L NHK

Size / Type
Rated voltage [V] Noiseless soft brake Rated torque [Nm] Rated speed (1/min) Rated current [A] Rated power consumption [W] Shaft diameter Protection class (IP) Limit switch range (revolutions) Operating time (min S2) Length C [mm] Length D [mm] Length E [mm] Ø F [mm] Weight [kg] Ambient operating temperature [°C] Connection NHK: 6 kant conn. 7 mm 4 kant conn. 6 mm
Protection class I Plug-in connection cable [m] Item number

VariEco M20 NHK 1 ~ 230 · 20 14 0,90 200

VariEco M30 NHK 1 ~ 230 30 14 0,90 200

VariEco M40 NHK 1 ~ 230 40 14 1,05 242

VariEco M50 NHK 1 ~ 230 50 14 1,30 300

VariEco L40 NHK 1 ~ 230 40 14 1,45 333