2MP Dome Network Camera
Product Information: Vandal Dome Network Camera
The Vandal Dome Network Camera is a device that allows for
remote monitoring of an area through its built-in image sensor and
network connectivity. The camera is designed to be durable and
resistant to vandalism, making it suitable for use in public areas.
It comes with a quick setup guide and user manual that provide
important information on proper usage and installation.
Product Usage Instructions:
- Precautions: Before using the device, fully
understand the user manual and strictly observe the rules in it. If
installing the camera in public places, provide a notice to inform
people that they are entering an area under electronic
surveillance. - Installation: Follow the installation
instructions provided in the user manual to ensure proper
installation. The manufacturer is not responsible for any damage
caused by non-conformance to these requirements. - Power Supply: Use power adapters that are
marked with the LPS standard and meet input voltage requirements
for the device. If installed in places with unsteady voltage,
ground the device to prevent power supply damage from electrical
surges. - Maintenance: Clean the device with a soft dry
cloth. For stubborn dirt, dip the cloth into slight neutral
cleanser, gently wipe the dirt with the cloth, and then dry the
device. Do not jam the ventilation opening. - Environmental Factors: Protect the device from
fall-down and intensive strikes, keep it away from magnetic field
interference, and do not install it in places with shaking surfaces
or under shocks. Keep it away from heat sources such as radiators,
electric heaters, or other heat equipment. Keep it away from moist,
dusty, extremely hot or cold places, or places with strong electric
radiation. If installed outdoors, take insect- and moistureproof
measures to avoid circuit board corrosion that can affect
monitoring. - Caution: Avoid heavy loads, intensive shakes,
and soaking to prevent damages during transportation and storage.
The warranty does not cover any device damage that is caused during
secondary packaging and transportation after the original packaging
is taken apart. - Warning: Failure to correctly use electrical
products may cause fire and severe injuries. Water or any liquid
flowing into the device while in use can cause damage; immediately
power off the device and disconnect all cables (such as power
cables and network cables) from this device. Do not focus strong
light (such as lighted bulbs or sunlight) on the device.
Vandal Dome Network Camera Quick Setup Guide
this device. Otherwise, the service life of the image sensor may be shortened. Y If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.
CAUTION
Y Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
Y Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
Y Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
Y Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
Y Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
Y Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
Y If the device is installed outdoors, take insect- and moistureproof measures to avoid circuit board corrosion that can affect monitoring.
Y Remove the power plug if the device is idle for a long time.
NO:101-100-0426-04 Issue:1.4
Precautions
Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.
It alerts you to moderate dangers which, if not WARNING avoided, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may
CAUTION
cause device damage, data loss, device performance deterioration, or unpredictable results.
NOTE It provides additional information.
WARNING
Y Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
Y Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
Y Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
Y If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
Y When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
Y Do not focus strong light (such as lighted bulbs or sunlight) on
Special Announcement
Y All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
Y The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
Y This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
Y This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.
NOTE
For more information, please refer to website.
1 Open Package Examination
Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.
Table 1-1 Packing list
Component Vandal Dome Network Camera Quick Setup Guide T15 Screw driver T10 Screw driver Installation location sticker Stainless self-tapping screw PA4.0×30mm Swell plastic button5.6×29mm Network access port protective cover Waterproof rubber seal Terminal block
Quantity 1 1 1 1 1 3 3 1 1 1
Remark Large Dome Mini Dome
Optional
2 Device Structure
2.1 Device Ports NOTE Len adjustment is only applied for large dome.
Figure 2-1 Lens adjustment
Port Name
Focusing lever Zoom lever Table 2-1 Lens adjustment description Description
Focusing lever Adjust the focus of lens, the default status is lock.
Zoom lever
Adjust the lens focal length, the default status is lock.
NOTE
Figure2-2 Multi-head cable 1
Different device may have different multi-head, please refer to the actual product.
1
Figure2-3 Multi-head cable 2 1
Po r t
2
3
4
Reset
5
Type1
IN G OUT G
6
Orange: Alarm com0 Some models’ alarm cable Yellow: Alarm In0
maybe show this type.
Grey: Alarm OUT1
Table 2-3 Multi-head cable 2 descriptiPounrple: Alarm Com
ID Core
Description
Remark
1
Network access port
Connects to a standard Ethernet cable or PoE . The green light is on, the network connection is normal; the yellow light flashes when the data is transmitted.Some models maybe not have the lights, please refer to actual product.
Support PoE supply.
2
Audio output
Connects to an external audio device such as a speaker.
Applied for camera with
3
Audio input port
Receives an analog audio signal from devices such as a sound
audio function
pickup device.
Long press the reset button 5
4
Reset botton seconds to restore the original settings.
5 Power supply Connects to a 12V direct current (DC 12V) (DC) power supply.
6G OUT
G IN
Alarm output COM Alarm output terminal Alarm input COM Alarm input terminal
Applied for alarm function
2.2 Camera Dimensions NOTE
Different device may have different dimensions, please refer to the actual product.
Figure 2-4 Dimensions of Mimi DomeUnit:mm
85.4 45
28.8
120°
Power
2
Reset
3Some models
may not have Table 2-2 Multi-head cable description
ID Core
Description
Remark
1 Network access port
Connects to a standard Ethernet cable or Support
PoE . The green light is on, the network PoE
connection is normal; the yellow light
supply.
flashes when the data is transmitted.
Some models maybe not have the lights,
please refer to actual product.
2
Power supply Connects to a 12V direct current (DC) (DC 12V) power supply.
3
Reset button
Long press the reset button 5 seconds to restore the original settings.
Ø1Ø11000
120°
Ø4.5
Figure 2-5 Dimensions of Large Dome(Unit:mm
130 123.18
137.0° 19.3 40
112.24
100.0°
123.0°
3 Device Installation
WARNING To avoid moisture influence, install the dome cover at least half an hour after the camera is installed and powered on. The vandal dome camera can be installed in the ceiling , wall , wall bracket or ceiling bracket. This section describes how to install the camera in the ceiling. Installation Steps: Step 1 Use the T15 screw driver in the accessory package to
unscrew the three screws on the dome cover. The camera is opened, as shown in figure 3-1.
Figure 3-1 Opening camera
Large Dome
Mini Dome
Step 2 Stick the Installation location sticker on the ceiling or wall, Drill three holes based on the marks on the sticker. Drive the swell plastic buttons into the holes.
Step 3 Fetch three black self-tapping screws from the accessory package. Then fix the screws to fasten the camera on the ceiling as shown in figure 3-2.
Top routing
Aside routing
Figure 3-2 Installing housing
Swell plastic buttons
Top routing
Aside routing
Swell plastic buttons
Selftapping screws
Large dome with lining
Selftapping screws
Mini dome
Step 4 Connect the network access port and power supply of the multi-head cable.
Step 5 Adjust the lens focal length and video angle range. 1.Press the arrows marked on the lining to remove the lining aside, as shown in figure 3-3.
2.View the video, loosen the slotted screw slightly as shown in figure 3-4 & figure 3-5, make camera’s triaxial adjustments, adjust the screen to the scene you want to monitor, and then tighten the screws. Three-axis adjustment direction and angle are shown in figure 3-4 & figure 3-5.
lining Arrows
Figure 3-3 Removing lining lining
Large dome with lining
Mini dome
Figure 3-4 Three-axis adjustment
Horizontal rotating
0°~350°
Screw
Vertical rotating 0°~75°
Figure 3-5 Adjusting lens
Horizontal rotating 350°
Lens axis rotating 350°
Lens axis rotating 0°~350°
Mini dome
Vertical Large dome rotating 80°
Figure 3-6 Installing SD card Large dome Insert
SD card
Mini dom
Insert SD card
Step 5 Loosen the focus lever, and gently move the zoom lever to adjust the lens focal length to the desired position. Move the focus lever slightly to focus the lens clearly. Tighten the focus lever after completing the focusing operation, as shown in figure 3-4(This step is only applied for large dome).
NOTE Y Some models maybe not operate so much steps, please refer to actual product. Y While focusing lever is in the process of focusing, an image might be blur, move the zoom lever to fine-tune the image, when image is clear, lock the zoom lever. Y If the lens of camera is auto focus lens, Set the focus value in Sensor > Lens control page in web page.
Step 6 Assemble the lining with the main body and buckle the four button placements with the main body bracket. Aim the two screws hole with boss at the groove on the main body. Then fasten the dome cover , as shown in figure 3-6.
Figure3-7 Assembling lining and cover
Four buttons
lining
two buttons
cover
Large dome
T15 screwdriver
T10 screwdriver Mini dome
4 Quick Configuration(e.g IE)
4.1 Login Step 1 Open the Internet Explorer, enter the IP address of IP camera
(default value: 192.168.0.120 in the address box, and press Enter. The login page is displayed. as shown in figure 4-1 . Step 2 Input the user name and password.
NOTE The default user name is admin. The default password is admin.
Y
Change the password when you log in the system for first time to ensure system security. You can change the system display language on the login page.
Figure 4-1 Login
User Name Password
English
Step3 Click Login, the main page is displayed. 4.2 Modify IP address
Choose Configuration > Device > Local Network, the Local Network page is displayed.
Enter the IP address in the IP Address box and click Apply as shown in figure 4-2.
After the success of the IP address setting, please use the new IP address to log in the Web interface.
Figure 4-2 Local Network
Local Network
IP Protocol
DHCP IP Address Subnet Mask Default Gateway
Preferred DNS Server Alternate DNS Server MTU(800-1500)
Refresh
Apply
4.3 Browsing Video To ensure the real-time video can be played properly, you must
perform the following operation when you log in the web for the first time:
Step 1 the Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 4-3.
Step 2 In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 4-4.
Figure 4-3 Adding a trusted site
Figure 4-4 Configuring ActiveX control and plug-in
Step 3 Download and install the player control as prompted.
NOTE
If the repair tips displayed when installing the control , please ignore the prompt, and continue the installation, the login page is displayed when the control is loaded.
To browse a real-time video, click Live Video. The Live Video page is displayed, as shown in figure 4-5.
Figure 4-5 Live Video
Live Video
Playback
Configuration
Stream stream1
Camera 1
