World Eyecam 1029 Vandal Proof Dome Network Camera User Guide (+ PDF)

All installation and operation should conform to your local
electrical safety codes.
The power source must conform to the Safety Extra Low Voltage
(SELV) standard and supply power with a rated voltage that conforms
to the Limited Power Source requirement according to
IEC60950-1.
Ensure that the power supply is correct before operating the
device.
A readily accessible disconnect device should be incorporated
in the building installation wiring.
Prevent the power cable from being trampled or pressed,
especially the plug, power socket, and junction extruded from the
device.

Environment

Do not aim the device at strong light sources, such as lamp
light and sunlight, as it may cause over brightness or light marks
that are not device malfunctions and can affect the longevity of
the Complementary Metal-Oxide Semiconductor (CMOS).
Avoid placing the device in damp or dusty environments,
extremely hot or cold temperatures, areas with strong
electromagnetic radiation, or locations with unstable
lighting.
Keep the device away from any liquid to avoid damage to the
internal components. Avoid exposing the indoor device to rain or
dampness to prevent fire or lightning.
Maintain proper ventilation to avoid heat accumulation.
Transport, use, and store the device within the allowed
humidity and temperature range. Avoid heavy stress, violent
vibration, or water splash during transportation, storage, and
installation.
When transporting the device, pack it with standard factory
packaging or equivalent material.
Install the device in a location accessible only to
professional staff with relevant knowledge of safety guards and
warnings. Non-professionals entering the installation area while
the device is operating normally may risk accidental injury.

Operation and Daily Maintenance

Avoid touching the heat dissipation component of the device to
avoid scalding.
Follow the instructions in the manual carefully when performing
any disassembly operation.
For enhanced reliability, it is recommended to connect the
grounding hole of the device to the ground.
Avoid touching the image sensor directly (CMOS). Dust and dirt
can be removed with an air blower or by gently wiping the lens with
a soft cloth moistened with alcohol.
Clean the device body with a soft dry cloth. Stubborn stains
can be removed by moistening the cloth with mild detergent. Do not
use volatile solvents such as alcohol, benzene, diluent, or strong
abrasive detergents, as they may damage the device body coating and
cause performance decrease.

View Fullscreen

Vandal Proof Dome Network Camera
Quick Start Guide
V1.0.3

Quick Start Guide
Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened.
All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device.
If there is any uncertainty or controversy, please refer to our final explanation.
II

Quick Start Guide
Important Safeguards and Warnings
Electrical safety
All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply
power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. Please note that the power supply requirement is subject to the device label. Make sure the power supply is correct before operating the device. A readily accessible disconnect device shall be incorporated in the building installation wiring. Prevent the power cable from being trampled or pressed, especially the plug, power socket and the junction extruded from the device.
Environment
Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it might cause over brightness or light marks, which are not the device malfunction, and affect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).
Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, or the locations with strong electromagnetic radiation or unstable lighting.
Keep the device away from any liquid to avoid damage to the internal components. Keep the indoor device away from rain or damp to avoid fire or lightning. Keep sound ventilation to avoid heat accumulation. Transport, use and store the device within the range of allowed humidity and temperature. Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation. Pack the device with standard factory packaging or the equivalent material when transporting
the device. Install the device in the location where only the professional staff with relevant knowledge of
safety guards and warnings can access. The accidental injury might happen to the non-professionals who enter the installation area when the device is operating normally.
Operation and Daily Maintenance
Do not touch the heat dissipation component of the device to avoid scald. Carefully follow the instructions in the manual when performing any disassembly operation
about the device; otherwise, it might cause water leakage or poor image quality due to unprofessional disassembly. Please make sure that the gasket ring is flat and properly installed in the groove before installing the cover. Please contact after-sale service for desiccant replacement if there is condensed fog on the lens after unpacking or when the desiccant turns green (Not all models are included with the desiccant). It is recommended to use the device together with lightning arrester to improve lightning protection effect.
III

Quick Start Guide
It is recommended connect the grounding hole to the ground to enhance the reliability of the device.
Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.
Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn stains when moistened with mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive detergent be used.
Dome cover is an optical component, do not touch or wipe the cover with your hands directly during installation or operation. For removing dust, grease or fingerprints, wipe gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower to remove dust. WARNING
Please strengthen the protection of network, device data and personal information by adopting measures which include but not limited to using strong password, modifying password regularly, upgrading firmware to the latest version, and isolating computer network. For some device with old firmware versions, the ONVIF password will not be modified automatically along with the modification of the system password, and you need to upgrade the firmware or manually update the ONVIF password.
Use standard components or accessories provided by manufacturer and make sure the device is installed and maintained by professional engineers.
The surface of the image sensor should not be exposed to laser beam radiation in an environment where a laser beam device is used.
Do not provide two or more power supply sources for the device unless otherwise specified. A failure to follow this instruction might cause damage to the device.
IV

Quick Start Guide
Table of Contents
Foreword……………………………………………………………………………………………………………………………………….. I Important Safeguards and Warnings………………………………………………………………………………………………. III 1 Introduction………………………………………………………………………………………………………………………………… 1
Cable ………………………………………………………………………………………………………………………………………………………………………..1 Connecting Alarm Input/output ………………………………………………………………………………………………………………………… 2 2 Network Configuration ………………………………………………………………………………………………………………… 4 Initializing Device…………………………………………………………………………………………………………………………………………………..4 Modifying Device IP Address ………………………………………………………………………………………………………………………………. 5 Logging in to Web Interface ………………………………………………………………………………………………………………………………..6 3 Installation………………………………………………………………………………………………………………………………….. 8 Packing List……………………………………………………………………………………………………………………………………………………………..8 Dimension………………………………………………………………………………………………………………………………………………………………. 8 Installing Device …………………………………………………………………………………………………………………………………………………….9
3.3.1 Installation Method……………………………………………………………………………………………………………………………………9 3.3.2 Installing SD Card (Optional) …………………………………………………………………………………………………………………… 9 3.3.3 Attaching Device………………………………………………………………………………………………………………………………………10 3.3.4 Installing Waterproof Connector …………………………………………………………………………………………………………..12 3.3.5 Adjusting Angle………………………………………………………………………………………………………………………………………..13
V

Alarm output

Quick Start Guide

Log in web interface, and configure alarm input and alarm output in alarm setting. The alarm input in the web interface is corresponding to the alarm input end of the I/O
port. There will be high level and low level alarm signal generated by the alarm input device when alarm occurs, set the input mode to “NO” (default) if the alarm input signal is logic “0” and to “NC” if the alarm input signal is logic “1”. The alarm output in the web interface is corresponding to the alarm output end of the device, which is also alarm output end of the I/O port.

2 Network Configuration

Quick Start Guide

Device initialization and IP setting can be finished with the “ConfigTool” or in web interface. For more information, see the WEB Operation Manual.
Device initialization is available on select models, and it is required at first use and after device is being reset.
Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stays in the same network segment.
Planning useable network segment properly to connect the device to the network. The following figures and interfaces are for reference only, and the actual product shall prevail.

Initializing Device
Double-click “ConfigTool.exe” to open the tool. Click . The Modify IP interface is displayed. See Figure 2-1.
Modify IP interface

Click Search setting. The Setting interface is displayed. Enter the start IP and end IP of the network segment in which you want to search devices, and then click OK. All the devices found in the network segment are listed. Select one or several devices whose Status is Uninitialized, and then click Initialize.
4

The Device initialization interface is displayed. Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2.
Password setting interface

Quick Start Guide

Set and confirm the password of the devices, and then enter a valid email address. Click Next. The final setting interface is displayed.
Password can be modified or reset in System Settings. Select the options according to your needs and then click OK. The Initialization interface is displayed after initializing is completed. Click the success icon ( ) or the failure icon ( ) for the details. Click Finish. The device status in the Modify IP interface (Figure 2-1) turns to Initialized.
Modifying Device IP Address
You can modify IP address of one or multiple devices in one time. This section is based on modifying IP addresses in batch.
Modifying IP addresses in batch is available only when the corresponding devices have the same login password. Follow Step 1 to Step 4 in 2.1 to search devices in your network segment.
After clicking Search setting, please make sure the username and password are the same as what you set during initialization, otherwise there will be “wrong password” notice.
5

Quick Start Guide
Select the devices which IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed. See Figure 2-3.
Modify IP Address interface
Select Static mode and enter start IP, subnet mask and gateway. IP addresses of multiple devices will be set to the same if you select Same IP. If DHCP server is available in the network, devices will automatically obtain IP
addresses from DHCP server when you select DHCP. Click OK.
Logging in to Web Interface
Open IE browser, enter the IP address of the device in the address bar and press Enter. If the setup wizard is displayed, follow the instructions to finish the settings. Enter user name and password in the login box, and then click Login. For first time login, click Click Here to Download Plugin and install the plugin as instructed. The main interface is displayed when the installation is finished. See Figure 2-4.
6

Main interface

Quick Start Guide

3 Installation

Quick Start Guide

Packing List
The tools required for the installation including electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the actual
packing shall prevail.

Dimension
Following figures are for reference only, the actual product shall prevail. (Unit: mm [in])

Installing Device
3.3.1 Installation Method

Quick Start Guide

3.3.2 Installing SD Card (Optional)
SD card slot is available on select models. Disconnect the power from the device before installing the SD card.
9

Quick Start Guide
Pressing reset button: Short press reset button for 1-2 s, press WPS button on the router and the device can be
connected to corresponding router within 1 minute (only supported by some models). Press the reset button for 10 seconds to reset the device.
3.3.3 Attaching Device
Make sure the mounting surface is strong enough to hold at least three times of the device weight.
10

Cable going through the mounting surface

Quick Start Guide

Cable going through the side cable tray

Quick Start Guide

3.3.4 Installing Waterproof Connector
This part is only needed when a waterproof connector comes with the device and the device is used outdoor.
12

Quick Start Guide
3.3.5 Adjusting Angle
Vertical rotation ring is available on select models, which fails to support image rotation. Please refer to the real model for more details.
IR light layout is different according to different models; please refer to the real model for more details.
Please be aware of image rotation direction when it turns to 64° vertically, which is to avoid IR light being blocked by enclosure and causing bad IR effect.
13

World Eyecam 1029 Vandal Proof Dome Network Camera User Guide

1029 Vandal Proof Dome Network Camera

Product Information

Product Usage Instructions

1. Upgrading the Reader Software

2. Trademarks and Ownership

3. Troubleshooting

4. Uncertainty or Controversy

Important Safeguards and Warnings

Electrical Safety

Environment

Operation and Daily Maintenance

Documents / Resouces

Related Manuals