CAN035 Roof Rack Polaris
Product Information: Roof Rack for Polaris RZR Pro R 4 Seater
(CAN035)
The Roof Rack (CAN036) is an off-road use only product that can
be installed over the original roof of Polaris RZR Pro R 4 Seater.
The product is available for purchase at AFX Motorsports. The roof
rack comes with a liability statement that requires all screws to
be tightened for safety.
Product Usage Instructions:
Tools Needed: 5/32 Allen Key, 7/16 or 14 mm
Combination Wrench (not included)
- Assemble the front of the roof rack with the front laterals
using four 1/4 x 3/4 screws with nuts. Do not tighten yet. - Align three central bars with the perforations and use twelve
1/4 x 1/2 screws with nut, inserting them bottom-up. Do not tighten
yet. - Assemble the rear of the roof rack with the lateral using four
1/4 x 3/4 screws with nut. Do not tighten yet. - Align three central bars with the perforations and use twelve
1/4 x 1/2 screws with nut, inserting them bottom-up. Do not tighten
yet. - Join the rear rack to the front rack, aligning the brackets
with the perforations using eight 1/4 x 1/2 screws with nut. Do not
tighten yet. - With the help of another person, place the complete rack over
the original roof and align the perforations. Use the six screws
you removed from the roof to tighten all the screws. - Align the last central bar with the perforations as shown in
the image and use four 1/4 x 1/2 screws with nut, inserting them
bottom-up. - Tighten all screws for safety.
Note: The figure on the bracket should be placed down and to the
front.
ROOF RACK INSTALLATION MANUAL
[email protected] THIS PRODUCT IS FOR OFF ROAD USE ONLY
POLARIS RZR PRO R 4 SEATER
CAN035
FOR PURCHASING AT AFX MOTORSPORTS
THE ROOF RACK CAN036 CAN ONLY BE INSTALLED OVER THE ORIGINAL ROOF
HOW TO INSTALL
Rear Roof Rack
Central bar Bracket
9 With the Help of another person, place the complete rack over
the Original Roof and aligning the perforations. Use the six screws you removed from the roof, tighten all the screws
Rear Lateral
Front Laterals
(8x) 1/4″ x 3/4″ Screw (36x) 1/4″ x 1/2″ Screw (44x) 1/4″ Lock nut
Tools Needed (Not Included) 5/32″ Allen Key 7/16″ or 14 mm Combination Wrench
Front Roof Rack
Liability Statement
AFX Motorsports products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by AFX Motorsports and is not recommended. AFX Motorsports products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact AFX Motorsports to verify that they will work together. Although AFX Motorsports has thousands of satisfied customers, user should be aware that installing bumpers, rock sliders, spare tire carriers, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. AFX Motorsports urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing AFX Motorsports products, user agrees that should damages occur, AFX Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. AFX Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from AFX Motorsports. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AFX Motorsports will warranty only parts provided by AFX Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by AFX Motorsports. AFX Motorsports parts and products are not warrantied if item was not installed properly, misused, or modified.
* For safety tighten all the screws *
6 Align the last central bar with the perforations (as it is shown
in the image). Use four 1/4″ x 1/2″ screws with nut, inserting them bottom-up
1 Assemble the Front of the roof rack with the Front laterals
(as it is shown in the image). Use four 1/4 x 3/4″ screws with nuts. (Do not tighten yet)
Front Roof Rack
Front Laterals
1/4″ Lock nut
1/4″ x 3/4″ Screw
7 Remove the six screws of the roof and keep them with you
2 Align 3 central bars with the perforations. Use twelve
1/4″ x 1/2″ screws with nut, inserting them bottom-up. (Do no tighten yet)
1/4″ Lock nut
1/4″ x 1/2″ Screw
Central bar
3 Assemble the Rear of the roof rack with the lateral (as it is shown
in the image). Use four 1/4 x 3/4″ screws with nut. (Do not tighten yet)
1/4″ x 3/4″ Screw
Laterals
1/4″ Lock nut
5 Join the rear rack to the front rack, aligning the Brackets
with the perforations (as it is shown in the image), using eight 1/4 x 1/2″ screws with nut. (Do not tighten yet).
Bracket
Front Rack
Rear Roof Rack
4 Align 3 central bars with the perforations. Use twelve
1/4″ x 1/2″ screws with nut, inserting them bottom-up. (Do no tighten yet)
1/4″ Lock nut
Central bar
1/4″ x 1/2″ Screw
Rear Rack
The figure on the Bracket should be placed down and to the front
