QWXCJ001 20V Cordless High Pressure Washer
Product Overview
The HOTO 20V Cordless High Pressure Washer is a compact and
portable device designed for various cleaning applications. It
comes with a multifunctional jet nozzle, foam tank, transparent
water inlet hose, self-priming water filter, 20V charger, battery
pack release button, inlet hose connector, and safety lock.
Operating Procedures
- Wear goggles, earmuffs, a protective suit, and non-slip shoes
when operating. - Insert the 20V battery pack into the battery holder on the
device. - Connect the quick connector of the inlet hose to the inlet hose
connector. Put the self-priming filter into the water after
connection. Make sure the filter is fully immersed in the
water. - Connect the multifunctional jet nozzle to the device. Unlock
the Safety Lock, pull the trigger to turn on the device. - Connect the foam tank to the quick connector of the device.
Pull the trigger to spray the foam.
After Use
- Disconnect the multifunctional jet nozzle.
- Pull down the quick connector of the hose. Take the
self-priming filter out of the water. - Press the battery pack release button and take out the battery
pack. - Unplug the waterproof plug on the battery pack charging hole
and insert the charger for charging. When the red charging light is
on, it indicates normal charging. When the red light turns green,
it indicates the completion of charging. Please use the original
charger!
Maintenance for Longer Service Life
- Take off the filter net at the inlet hose connector. Screw off
the self-priming filter and take out the filter net. - Rinse the filter nets with clean water in time (It is
recommended that the filter nets be cleaned once every 3 to 5 times
of use according to the local water supply). - Please pay attention to the battery level and charge in time
when the battery level is low. Frequent loss of power may lead to
the sleep state of the battery pack.
Technical Specifications
- Name: HOTO 20V Cordless High Pressure Washer
- Model: QWXCJ001
- Battery Type: Lithium-ion battery pack
- Rated Voltage: 20V
- Capacity: 200W
- Water Pressure: 24bar
Application Scenarios
This device is applicable to car washing, deep cleaning such as
window washing, and plants watering or light cleaning.
Product Safety
WARNING: Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric
shock, fire and/or serious injury. Save all warnings and
instructions for future reference.
WARNING: This product can expose you to chemicals including
lead, phthalate or bisphenol A which are known to the State of
California to cause cancer, birth defects or other reproductive
harm. Wash your hands after use. For more information go to
www.P65Warnings.ca.gov.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using this product basic precautions should always
be followed, including the following:
- Read all the instructions before using the product.
- To reduce the risk of injury, close
SAFETY WARNINGS FOR BATTERY PACK
- Do not dismantle, open or shred battery pack.
- Do not expose battery pack to heat or fire. Avoid storage in
direct sunlight.
01 Product Overview
Please read this manual carefully before use, and retain it for future reference.
1 2
3 4
9 8 7 6 5
1 Multifunctional Jet Nozzle
2 Foam Tank
3 Transparent Water Inlet Hose
4 Self-priming Water Filter
5 20V Charger
6 Ba ery Pack Release Bu on
7 Ba ery Pack Charging Hole 8 Inlet Hose Connector 9 Safety Lock
1
02 Operating Procedures
1. Please wear goggles, earmuffs, a protective suit, and non-slip shoes when operating. 2. Insert the 20V ba ery pack into the ba ery holder on the device.
3. Connect the quick connector of the inlet hose to the inlet hose connector. Put the self-priming filter into the water a er connection. Make sure the filter is fully immersed in the water. 4. Connect the multifunctional jet nozzle to the device. Unlock the Safety Lock, pull the trigger to turn on the device. 5. Connect the foam tank to the quick connector of the device. Pull the trigger to spray the foam.
2
03 A er Use
1. Disconnect the multifunctional jet nozzle. 2. Pull down the quick connector of the hose. Take the self-priming filter out of the water. 3. Press the ba ery pack release bu on and take out the ba ery pack. 4. Unplug the waterproof plug on the ba ery pack charging hole and insert the charger for charging. When the red charging light is on, it indicates normal charging. When the red light turns green, it indicates the completion of charging. Please use the original charger!
3
04 Maintenance Longer service life for the device
1. Take off the filter net at the inlet hose connector. Screw off the self-priming filter and take out the filter net.
2. Rinse the filter nets with clean water in time (It is recommended that the filter nets be cleaned once every 3 to 5 times of use according to the local water supply).
3. Please pay a ention to the ba ery level and charge in time when the ba ery level is low. Frequent loss of power may lead to the sleep state of the ba ery pack.
05 Technical Specifications
Name: HOTO 20V Cordless High Pressure Washer Model: QWXCJ001 Ba ery Type: Lithium-ion ba ery pack Rated Voltage: 20V Capacity: 200W Water Pressure: 24bar
Flow Rate: 180 L/h Feed temperature: 0-40°C Charging time: 3-5h Operating time: Around 20min Weight: 2.25kg
4
05 Application Scenarios
Applicable to car washing Applicable to deep cleaning such as window washing Applicable to plants watering or light cleaning
5
06 Product Safety
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
WARNING: This product can expose you to chemicals including lead, phthalate or bisphenol A which are known to the State of California to cause cancer, birth defects or other reproductive harm. Wash your hands a er use. For more information go to www.P65Warnings.ca.gov.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using this product basic precautions should always be followed, including the following: 1. Read all the instructions before using the
product. 2. To reduce the risk of injury, close
supervision is necessary when a product is used near children. 3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls. 4. Stay alert watch what you are doing. 5. Do not operate the product when fatigued or under the influence of alcohol or drugs. 6. Keep operating area clear of all persons 7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. 9. WARNING Risk of injection or injury do not direct discharge stream at persons. 10. Do not spray electrical apparatus and wiring.
SAVE THESE INSTRUCTIONS
SAFETY WARNINGS FOR BATTERY PACK
a) Do not dismantle, open or shred ba ery pack.
b) Do not expose ba ery pack to heat or fire. Avoid storage in direct sunlight.
c) Do not short-circuit a ba ery pack. Do not store ba ery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects. When ba ery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the ba ery terminals together may cause burns or fire.
d) Do not remove ba ery pack from its original packaging until required for use.
e) Do not subject ba ery pack to mechanical shock.
f) In the event of ba ery leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
g) Observe the plus (+) and minus () marks on the ba ery back and equipment and ensure correct use.
h) Do not use any ba ery pack which is not designed for use with the equipment.
i) Keep ba ery pack out of the reach of children.
j) Seek medical advice immediately if a cell or ba ery has been swallowed.
k) Always purchase the ba ery pack recommended by the device manufacturer for the equipment.
l) Keep ba ery pack clean and dry. m) Wipe the ba ery pack terminals with a
clean dry cloth if they become dirty.
6
n) Ba ery pack need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
o) Do not leave ba ery pack on prolonged charge when not in use.
p) A er extended periods of storage, it may be necessary to charge and discharge the ba ery pack several times to obtain maximum performance.
q) Ba ery pack gives its best performance when it is operated at normal room temperature (20 °C ± 5 °C).
r) When disposing of ba ery packs, keep ba ery packs of different electrochemical systems separate from each other.
s) Recharge only with the charger specified by WORX Do not use any charger other than that specifically provided for use with the equipment. A charger that is suitable for one type of ba ery pack may create a risk of fire when used with another ba ery pack.
t) Retain the original product literature for future reference.
u) Use only the ba ery pack in the applica tion for which it was intended.
v) Remove the ba ery pack from the equipment when not in use.
w) Dispose of properly.
07 Operating Handheld
Lithium Car Washer
Help you quickly understand the installation details
Installation of Accessories
The inlet filter nets must always be in place to filter out sand, lime, and other impurities in that they will damage the pump valve.
Before delivery, the product is equipped with filter nets at the inlet hose connector and one end of the water inlet hose.
Installation of Components
Connect the multifunctional jet nozzle to the quick outlet connector on the device.
Screw tightly the foam tank to the device. Pour detergent into the foam tank. The detergent can be used to rinse off the dirt.
Water Connection
Connect to a low-pressure water supply
The device can operate under the self-priming mode, which means it can be connected to a water container, stream, lake, pond, etc. When drawing water from mains of undrinkable water, the backflow preventer is not required.
When connecting to a low-pressure water supply for operating, please use an external filter to make sure impurities will not be sucked in.
To meet these requirements, it is recommended to use the original water inlet components.
Use the new hose parts that come with the device; the old hose parts are non-reusable.
Make sure that the filter net is installed at the proper place of the inlet and that the inlet hose is connected to it tightly.
Turn on the device and pull the trigger. Wait until the nozzle discharges a steady stream of water.
7
Connect to pressurized water supply
The maximum feed pressure and temperature of the inlet are 0.7MPa/7bar and 40°C respectively.
– Check whether the filter is installed inside the inlet hose and is not blocked.
– Connect the hose to the water tap using the quick connector and then open the water tap.
Before connecting the hose to the device, let the water flow through the hose to prevent sand and dirt from entering the device.
– Turn off the water tap and connect the hose to the inlet using the quick connector.
8
08 troubleshooting
Issue
Possible Causes
Solution
The lithium ba ery
pack indicator
Insufficient ba ery power. Charge the ba ery in time.
flashes
No power a er turning on
Insufficient ba ery power. Charge the ba ery in time.
The ba ery pack is not Reinsert the ba ery pack into the ba ery
properly installed.
holder and make sure it is properly connected.
Unexpected halt
Automatic overheating protection.
Turn on a er it cools down.
The ba ery pack cannot be charged
The ba ery is not
Reinsert the charger into the charging hole
properly connected to the and make sure it is properly connected.
charger.
The charger is not connected to the power supply.
Unmatched charger.
Check whether the power supply is energized and make sure the charger is properly connected to it (the power indicator flashes or not). Charge using the original adapter.
The filter is clogged
Clean the filter net on the water filter and
Small water output causing poor water inflow. the inlet filter net. The inlet hose is folded. Straighten out or replace the water inlet hose.
Impure water supply.
Use clean water.
The nozzle is clogged.
Clean the jets inside the nozzle.
Fail to pump water
The hose connector is not Connect the inlet hose connector to the properly connected to the inlet properly. inlet. The self-priming water Fully immerse the water filter in the water. filter is not fully immersed in the water. The inlet seal ring falls off Install or replace the seal ring. or is damaged.
Long waiting time for water output
Small water output.
Refer to the solution for small water output.
Leaking water outlet
The nozzle is not properly Properly install the nozzle on the device. installed.
9
Manufacturer: Shanghai HOTO Technology Co., Ltd. Address: Building 45, No. 50 Moganshan Rd, Putuo District, Shanghai, PRC, 200060.
10
P65Warnings.ca.gov
