1007516309 7.5 Foot Elegant Grand Fir LED Pre-Lit Tree with Timer
Product Information
The 7.5 ft Elegant Grand Fir LED Pre-Lit Tree with Timer (SKU#
1007516309) is an artificial Christmas tree that comes with
built-in LED lights. The tree has three sections (top, middle, and
bottom) that need to be assembled using the included stand and eye
bolt. The tree also comes with a power cord, remote control, and
two rivets. The LED lights are non-replaceable, and the tree can
only be used with the original adapter.
Safety Information
When using electrical products, basic precautions should always
be followed including reading and following all safety
instructions. The product should be disconnected from its power
source before assembling or disassembling. Do not attempt to
replace lamps or modify the string of lights to reduce the risk of
fire or electric shock.
Product Usage Instructions
Pre-Assembly
Before assembling the tree, make sure you have all the necessary
components. The package includes a top section, middle section,
bottom section, stand with an eye bolt, power cord, remote control,
and two rivets.
Assembly
To assemble the tree stand:
- Choose a location near a wall outlet.
- Open the stand to a 90-degree angle until the hole lines up
with the hole on the tube. - Screw an eye bolt into the hole.
To assemble the tree:
- Remove protective covers from the base of each tree section
before assembling. - Insert the tree bottom (C) into the tree stand and tighten the
screw. - Insert the middle section (B) into the tree bottom (C).
- Insert the tree top (A) into the middle section (B).
- Allow branches to fall into place or gently pull branches up
and out.
Operation
To turn on the tree, connect each tree section well and plug the
power cord into a wall outlet.
Timer Function
The tree comes with a timer function that can be activated using
the remote control or control box. To turn off the timer function,
press the button on the control box or press the off button on the
remote control. The timer has a memory mode, so it will resume the
last setting even if the tree is unplugged and re-plugged back
on.
Remote Control
The remote control is used to turn on/off the lights or timer
function and select different timer hours. To use the remote
control, pull out the insulation tape from the remote control
before starting to use it. If the remote control does not work,
check whether the battery of the remote control is out of power. To
replace the remote control battery, replace it with a new button
cell CR2025 (3 volt) into the compartment. Do not dispose of
batteries in fire as they may explode or leak.
Control Box
The control box is used to turn on/off the lights or timer
function and activate the timer mode. To activate timer mode, press
and hold the button on the control box. The first indicator lights
of timer on the control box turn on for a 2-hours ON, 22-hours OFF
cycle. The second indicator lights of timer on the control box turn
on for a 4-hours ON, 20-hours OFF cycle. The third indicator lights
of timer on the control box turn on for a 6-hours ON, 18-hours OFF
cycle. The fourth indicator lights of timer on the control box turn
on for an 8-hours ON, 16-hours OFF cycle.
7.5 ft Elegant Grand Fir LED Pre-Lit Tree with Timer
SKU# 1007516309
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.57 A 120 V 60 Hz. c) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. d) This seasonal use product is not intended for permanent installation or use. e) Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat. f) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. g) Do not let lamps rest on the supply cord or on any wire. h) Unplug the product when leaving the house, when retiring for the night, or if left unattended. i) This is an electric product not a toy! To avoid risk of fire, burns personal injury and electric shock it should not be played with or placed where small children can reach it. j) Do not use this product for other than its intended use. k) Do not hang ornaments or other objects from cord, wire, or light string. l) Do not close doors or windows on the product or extension cords as this may damage the wire insulation. m) Do not cover the product with cloth, paper or any material not part of the product when in use. n) Do not move the tree by pulling the tree tips or tree branches. o) Read and follow all instructions that are on the product or provided with the product.
p) SAVE THESE INSTRUCTIONS.
CAUTION! ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR DISASSEMBLING.
CAUTION:
1. The product consists of non-replaceable LED lamps. To reduce the risk of fire or electric shock, do not attempt to replace lamps or modify string.
2. This product can only be used with the original adapter, not other brands of adapter.
Pre-Assembly
Package Contents
A. Top Section Qty: 1
B. Middle Section Qty: 1
C. Bottom Section Qty: 1
D.Stand with an eye bolt Qty: 1
E. Power Cord Qty: 1
F. Remote Control Qty: 1
G. Rivet Qty: 2
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet. Step 2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube. Step 3. Screw an eye bolt into the hole.
Assembling the tree
Please remove protective covers from the base of the pole for each tree section before assembling. Step 1. Insert tree bottom (C) into the tree stand and tighten the screw.
(See Fig. 1) Step 2. Insert middle section (B) into the tree bottom (C). (See Fig. 2) Step 3. Insert tree top (A) into the middle section (B). (See Fig. 3) Step 4. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch hinges. (See Fig. 4) Step 5. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one at the center of the main stem. Repeat pattern for each branch. (See Fig. 5) Step 6. Plug the power cord into a proper outlet. This tree comes with a control box and a remote control. You can change the lighting patterns of the tree by using control box or remote control. Please see Instructions of control box and remote control as below.
To turn off the timer function, press the button on control box or press the off button on remote control. There is memory mode on timer control even unplug and re-plug back on.
Instruction of remote control
Please note this tree has a remote control. Please pull out the insulation tape from the remote control, before starting to use it.
1. Press the button ON or OFF to turn on or off the lights or timer function. 2. Press the 2H, 4H, 6H or 8H button to select the different timer hours. If the remote control does not work, check whether the battery of the remote control is out of power. To replace the remote control battery: 1. Replace with a new button cell “CR2025” (3 volt) into
the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall outlet.
Instruction of control box and remote control
Instruction of control box
1. Press the button on control box to turn on and off the lights or timer function.
2. Press and hold the button on control box to activate timer mode, select below timer hours:
i. The first indicator lights of timer on control box turn on: The tree lights will automatically run through a 2-hours ON, 22-hours OFF cycle.
ii. The second indicator lights of timer on control box turn on: The tree lights will automatically run through a 4-hours ON, 20-hours OFF cycle.
iii. The third indicator lights of timer on control box turn on: The tree lights will automatically run through a 6-hours ON, 18-hours OFF cycle.
iv. The fourth indicator lights of timer on control box turn on: The tree lights will automatically run through an 8-hours ON, 16-hours OFF cycle.
Use and Care Instructions
a) Before using or reusing, inspect product carefully. Discard any products that have cut , damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
b) When storing the product, carefully remove the product from wherever it is placed, including tree, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
c) When not in use, store neatly in a cool, dry location protected from sunlight.
Care and Cleaning
Step 1. Remove all ornaments and decorations. Step 2. Unplug the power cord from the wall outlet. Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole. Step 4. Repeat this step for the center and bottom tree sections. Step 5. Carefully place all tree sections into a shipping box and tape it shut. Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
The tree or the tree top does not light
Solution
Ensure that all tree sections are connected into each other well by pressing each section down and rotating. Make sure the power cord is well connected to the tree bottom (C).
If you are still experiencing problems with the tree please call 1-800-986-3460 for instructions.
Top section does not light
Push downward and rotate the top section to B section to make sure they are connected securely.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Please note that changes or modifications
not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
a) To reduce the risk of electric shock, use only with the power-supply
cord provided or with a cord set intended for indoor use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Do not abuse cord Do not carry product by the cord or yank or pull
it to disconnect from the outlet.
d) Disconnect the product from the outlet when not in use.
Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it with a spare rivet (G). 1) Place the branch into the slot of the bracket. 2) Insert a spare rivet
through the hole and use diagonal pliers (not included) to crimp the rivet. (See Fig. A)
WARRANTY
3-year Limited Warranty This product carries a three (3) year warranty against defects in workmanship and materials. This product is not guaranteed against wear or breakage due to misuse and/or abuse.
Date Code: 04012022_2003186
Importer: The Home Depot Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339 Tel: 1-800-986-3460
Adapter Model No. TS-24WLF12V
