Philips Ddnp1501 Pdts Networked Touchscreen Instruction Manual (+ PDF)

Contents hide

DDNP1501 PDTS Networked Touchscreen

Product Information:

The PDTS Networked Touchscreen is a device that requires
professional installation by a qualified electrician. It must be
installed in accordance with all national and local electrical and
construction codes and regulations. The device is designed to be
used in home and building automation and control systems.

The PDTS model is DDNP1501, and it is compatible with the
DMNP24040-P-NA model. The dimensions of the device are 83 mm (3.27
in) x 68 mm (2.68 in) x 68 mm (2.68 in) x 124 mm (4.88 in). It has
an Ethernet port for connectivity.

The device is available in two styles: American Style (2A, 3A)
and European Style (2B, 3B). It operates on SELV/Class 2 (UL) power
supply with options for 12 V at 500 mA or 24 V at 300 mA.

The PDTS Networked Touchscreen complies with IEC Pollution
Degree II and IEC Overvoltage Category III standards. It utilizes
RS-485 DyNet communication protocol.

For more information, visit www.dynalite.com.

Product Usage Instructions:

Ensure that the device is installed by a qualified electrician
following all necessary electrical and construction codes and
regulations.
Connect the device to a suitable power supply according to the
required voltage and current specifications (+VDD+, GND,
SHLD).
Use clean damp cloth for cleaning the device. Do not use
corrosive or harsh cleaning agents.
Avoid connecting inputs to mains.
Refer to the Service Guide for detailed cleaning
recommendations.
Comply with IEC 60364 (all parts) when installing a home and
building automation and control system.
Ensure that the temperature limits and current-carrying
capacities for the communication wires specified in IEC 60364-5-52
are not exceeded.

View Fullscreen

PDTS
Networked Touchscreen

Installation Instructions
Instructions d’installation Installationsanweisungen Instrucciones de instalación Istruzioni per l’installazione Installatie-instructies

Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux.
Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren.

Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras.
I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici.
De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften.

/
.

DDNP1501

DMNP24040-P-NA

83 mm (3.27 in) 68 mm (2.68 in) 68 mm (2.68 in) 124 mm (4.88 in)

X 4 NA X 2 EU
X 4
1
300 mm (12 in)

Ethernet

46 mm (1.81 in)

12 mm (0.47 in)

93 mm (3.66 in) 121 mm (4.76 in) 184 mm (7.24 in)

28 mm (1.10 in)

300 mm

(12 in)

300 mm (12 in)

45° C (113° F) -0° C (32° F)

90%

2A
American Style
2B
European Style
IEC Pollution Degree II 4

3A
American Style

Ø < 7.5 mm (0.30 in)
< 3.5 mm (0.19 in)

European Style

Service

switch

5 RJ45 (Ethernet)
IEC Overvoltage Category III 6

DDNP1501 DMNP24040-P-NA THIRD PARTY
?

Required Supply: SELV/Class 2 (UL)

12 V

500 mA

24 V

300 mA

+ –

+V DD+ GND SHLD

0.3-2.5mm2 22-12 AWG

0.4 Nm 3.5 Lb-in

2 A

RS-485 DyNet SELV/Class 2 (UL)

10m 0.5 mm2

20m 0.75 mm2

20+ AWG

18+ AWG

Clean only with a clean damp cloth. DO NOT use corrosive or harsh cleaning agents
3

Do not connect inputs to mains.

Caution risk of explosion if battery is replaced by an incorrect type.

Refer to Service Guide for full cleaning recommendations.

Attention risque d’explosion si la pile est remplacée par un Type incorrect.

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user’s authority to operate this device.

This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la classe B est conforme a la norme NMB003 du Canada: CAN ICES-3(B)/NMB-3(B).

Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.

© 2023 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.

www.dynalite.com
AZZ 499 0523 R10