B01-004 Rodent Trap with BLE and LoRa
Product Information
The B01-004 is a device designed to monitor and transmit data
using LoRaWAN technology. The device is installed in a plastic
housing that is sonically welded for complete protection from
various installation environments and rodents. It requires a
ER14505H battery to be connected before installation. Once powered,
the device will advertise for 30 seconds before going to sleep.
Tapping the sensor pad a few times will wake the device up, and it
will again advertise for 30 seconds before going back to sleep. For
registered devices installed in the field, the device will
continually advertise every 1.5 seconds, and a LoRaWAN heartbeat
will transmit periodically based on how the device is
configured.
Product Usage Instructions
To use the B01-004 device, follow the instructions below:
- Connect a ER14505H battery to the device before installation
into plastic housing. - Install the device in the desired location.
- If the device is unregistered, tap the sensor pad a few times
to wake it up. The device will advertise for 30 seconds before
going back to sleep. - If the device is registered and installed in the field, it will
continually advertise every 1.5 seconds, and a LoRaWAN heartbeat
will transmit periodically based on how the device is
configured. - Regulatory information for Canada and the USA can be accessed
from the main screen (Dashboard) by performing the following steps:
(1) Access the Site Menu (upper left corner of the App screen) (2)
Select About Us from the Site Menu (3) Tap the button labeled
Regulatory.
B01-004 User Manual Revision 1.1
May 23, 2023
NOTICE TO READERS
This document contains proprietary information which is the property of
SMART WAVE TECHNOLOGIES CORP.
CONFIDENTIAL
Except for the right expressly granted in writing, this document may not, in whole or in part, be duplicated or disclosed without the prior written
permission of Smart Wave Technologies Corp.
5/23/2023
B01-004 User Manual Rev1.1
Page 2 of 6
TABLE OF CONTENTS
TABLE OF CONTENTS …………………………………………………………………………………………………………. 3 Product Description …………………………………………………………………………………………………………………. 4 Product installation ………………………………………………………………………………………………………………….. 4 Product operation…………………………………………………………………………………………………………………….. 4 Regulatory Information ……………………………………………………………………………………………………………. 5
5/23/2023
B01-004 User Manual Rev1.1
Page 3 of 6
PRODUCT DESCRIPTION
The B01-004 is a bait station data capture device used to detect rodents and insects that have entered the bait station and timestamp when the event occurred. The device uses a capacitive touch pad connected to capacitive touch sensor IC configured with customized filtering to provide information to the controller, which in turn uses a proprietary filtering algorithm to isolate events and detections. This information is passed to a mobile phone app, via Bluetooth, which will upload the information to a cloud server. The device is also equipped with LoRaWAN capabilities to provide direct device-to-cloud connection through a configurable heartbeat interval.
PRODUCT INSTALLATION
The B01-004 is installed in a plastic housing and sonically welded to provide complete protection from the various installation environments and rodents. A ER14505H battery must be connected to the B10-004 before installation into plastic housing
PRODUCT OPERATION
Once powered, the device will advertise for 30 seconds before going to sleep. Tapping the sensor pad a few times will wake the device up and it will again advertise for 30 seconds before going back to sleep. This operation will happen for device that are unregistered (Factory Mode).
For devices that are registered and installed in the field, the device will continually advertise every 1.5 seconds. A LoRaWAN heartbeat will also transmit periodically according to how the device is configured.
5/23/2023
B01-004 User Manual Rev1.1
Page 4 of 6
REGULATORY INFORMATION
CANADA ISED Regulatory Statements IC: 24934-B01004
ISED non-interference disclaimer This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
RF Exposure statement This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux radiations ISED CNR-102 établies pour un environnement non contrôlé. Une distance de séparation d’au moins 20 cm doivent être maintenue entre l’antenne de cet appareil et toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
CAN ICES-3 (B)/NMB-3(B) Regulatory information in the App can be accessed from the main screen (Dashboard) by performing the following steps: (1) Access the Site Menu (upper left corner of the App screen) (2) Select “About Us” from the Site Menu (3) Tap the button labeled “Regulatory”
5/23/2023
B01-004 User Manual Rev1.1
Page 5 of 6
USA FCC Regulator Statements FCC: 2ASYW-B01004
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.
NOTICE: End user must include the following on the label of the end product
FCC ID: 2ASYW-B01004 IC: 24934-B01004
5/23/2023
This is the Last Page of this Document B01-004 User Manual Rev1.1
Page 6 of 6
