SKR1xx Flow Star Bonded Water Stop Skimmer
Product Information: – Product Name: Skimmer (Model: SKR1xx,
SKR15xxx, SKR2xx, SKR17xxx, SKR14xxx, SKR32xx) – Flow Rate: – 2
1/2” Pipe: Max Flow – 90 GPM, Min Flow – 15 GPM – 2” Pipe: Max
Flow – 63 GPM, Min Flow – 15 GPM – Certification: Certified to
NSF/ANSI/CAN 50 for public and residential installation – Safety:
The skimmer is not equivalent to a main drain. If not using a
single, unblockable drain, all pools, spas, and hot tubs must have
at least two main drains besides skimmer(s) or a single,
unblockable drain. – Maintenance: Periodically check the weir for
free operation. Replace if damaged or worn. Check the strainer
basket as often as needed for accumulated leaves, debris, etc.
Empty the basket as required. Regularly check the condition of the
skimmer deck lid. If any sign of damage or deterioration is found,
replace the deck lid and fasteners. – Winterizing: Drain the pool
until the level is below the skimmer inlet. Remove the cover,
basket, and float. Plug bottom port(s). Cover the skimmer to
prevent rainwater or snow from entering and freezing. Product
Usage Instructions: 1. Water Level: Keep the pool, spa, or hot
tub water level at the middle water level mark for best
performance. Do not operate below the low mark. 2. Operation
Overview: – Pump suction pulls water through the skimmer. – Water
flowing into the skimmer carries floating leaves, bugs, etc., where
they are trapped in the skimmer basket. – Dust, body oils, etc.,
pass through the basket to be removed by the filter. – The weir
door in the skimmer opening enhances surface flow and skimming
action. 3. Flow Adjustments: – Adjust shut-off valves located
before the pump to balance flow from pool main drains. 4. Vacuuming
Pool: – Remove the float valve, cleaner hose regulator valve,
skimmer cone plug, and equalizer (if present). – Connect the vacuum
cleaner hose to the pump suction. 5. Skimmer Layout and Suction
Line Sizing: – The minimum number of skimmers needed depends on the
facility type (refer to Table 1). – At least one skimmer should be
placed so that the prevailing wind blows towards the skimmer. Note:
For more detailed information on installation, operation, and
maintenance, please refer to the complete user manual or contact
AquaStar Pool Products customer support at P 877-768-2717 or
[email protected].
Max Flow
21/2” Pipe: 90 GPM 2” Pipe : 63 GPM
Certified to NSF/ANSI/CAN 50
FLOW STAR® SKIMMER
PUBLIC & RESIDENTIAL
INSTALLATION, OPERATION & PARTS
Min Flow
21/2” Pipe: 15 GPM 2” Pipe : 15 GPM
Float valve and deck lid are not NSF certified.
IMPORTANT SAFETY INSTRUCTIONS FOR SKR1xx, SKR1xx-L, SKR15xxx, SKR15xxx-L, SKR2xx, SKR2xx-L, SKR17xxx, SKR17xxx-L, SKR14xxx, SKR14xxx-L, SKR32xx, SKR32xx-L,
READ AND FOLLOW ALL INSTRUCTIONS
WARNING!
HAZARDOUS SUCTION. RISK OF HAIR OR BODY ENTRAPMENT, DROWNING OR DISEMBOWELMENT. When an equalizer is used, the opening in the pool shall be protected by a VGBA Compliant drain cover rated for 100 GPM or greater. NOTE: Skimmer is not equivalent to a main drain. If not using a single, unblockable drain, all pools, spas and hot tubs must have at least
two main drains besides skimmer(s) or a “single, unblockable” drain.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
OPERATION
Operation Overview
Pump suction pulls water through skimmer. Water flowing into skimmer carries floating leaves, bugs, etc., where they are trapped in the skimmer basket. Dust, body oils, etc., pass through the basket to be removed by the filter. Weir door in skimmer opening enhances surface flow and skimming action.
Water Level
Keep pool, spa or hot tub water level at the middle water level mark, on the data plate image located inside skimmer housing, for best performance. Never operate below the low mark, see Figure 1.
To Pump Suction
Plug
Adjust Shut-off
Valves to
Balance Flow
From Pool
Main Drains
Figure 2: Typical residential installation
Flow Adjustments
Figure 1: Data Plate Image
Adjust valves located before the pump, see Figure 2.
Vacuuming Pool
Remove deck lid and skimmer basket. If there is a float valve, remove it and plug equalizer port that is closest to the pool. Replace basket and place vacuum plate on top of basket. Fill the vacuum hose with water and then place your hand over the end of the hose as you bring it through the skimmer throat, or over the deck to attach it to the vacuum plate (Figure 3). Follow instructions in vacuum owner’s manual for vacuuming operation. After vacuuming, remove hose, vacuum plate and basket, unplug equalizer port and reinstall float valve, basket and deck lid.
Cleaner Hose
Regulator Valve Skimmer Cone Plug Equalizer and Remove Float Valve
Optional Equalizer Line (AquaStar’s Float Valve Is Not NSF Certified)
To Pump Suction
Figure 3: Vacuuming pool; float and check valves removed, equalizer port plugged.
P 877-768-2717 F 877-276-POOL [email protected] www.aquastarpoolproducts.com
MAINTENANCE
Periodically check weir for free operation. Replace if damaged or worn. Check strainer basket as often as needed for accumulated leaves, debris, etc. Empty basket as required.
Skimmer deck lid is made of impact and weather resistant materials, but extended use (5-10 years) may lead to reduced strength. Regularly check condition of skimmer lid. Look for cracks, chips, deterioration of plastic, etc. If any sign of damage or deterioration is found, replace the deck lid and fasteners.
To winterizing, drain pool until level is below skimmer inlet. Remove cover, basket and float. Plug bottom port(s). Cover skimmer to prevent rainwater or snow from entering the skimmer where it could freeze.
WARNING! LOW WATER LEVEL CAN MAKE IT DIFFICULT TO EXIT POOL AND MAY DAMAGE PUMP AND OTHER POOL EQUIPMENT. Note: An equalizer line is a way to bypass the skimmer and it is intended to inhibit damage to the pump when pool water level is below the throat of the skimmer or the basket is full. You must check your local code as some require equalizer lines, others don’t allow them and others leave it to the pool designer. When equalizer line is used the cover inside the pool must be VGBA compliant, and have a flow rating higher than the skimmer’s configuration-specific flow rating.
SKIMMER LAYOUT AND SUCTION LINE SIZING
Skimmers are critically important for removing floating contaminants, oils, and debris; for this reason modern pool building codes require that the number of skimmers installed are capable of handling 100% of the filtration flow rate.
1. The minimum number of skimmers needed is based on
facility type (See Table 1).
2. When selecting the location for skimmers, at least one
should be placed so that the prevailing wind blows towards the skimmer.
3. Size suction pipe based on the design flow rate such that
the water velocity in the pipe will not exceed six feet per second. To increase system flow capacity for long pipe runs, use multiple pipes (both ports) or larger pipe (2.5” spigot, or 3”/4” adapter bushing #BFB101). See figures 5 and 7 piping layout.
Table 1: Skimmers Required Per Square Foot Area
Facility Type
Public Pool Residential Pool Public and Residential Spa
Area Per Skimmer (sq. ft.)
500 800
150
Example: A public pool that is 1000 sq. ft. requires at least two skimmers.
INSTALLATION
See section “Dimensions and Parts list” and “Skimmer Head Loss and Installation Dimensions” for basic dimensions. Top cover frame has 1″ vertical height adjustment. NOTICE: Skimmer MUST be surrounded by at least 4″ of structural concrete in a monolithic pour.
PIPE CONNECTIONS AND TESTING Connect pump inlet line to rear port in bottom manifold. Skimmer manifold is PVC, and comes in a variety of configurations. For threaded connections inside skimmer manifold, do not use pipe dope; to seal joint use RTV Silastic #732 (preferred), Teflon tape or Plasto-Joint Stik. For slip connections, apply PVC primer to PVC pipe only. Then apply PVC to PVC solvent cement to both pipe and slip connections. Consult distributor for correct solvent cement for pipe used. Assemble joint per cement manufacturer’s instructions, allowing recommended set time before pressure testing.
WARNING! PLASTIC CEMENTS AND PRIMERS CAN BE FLAMMABLE, POISONOUS OR BOTH. CLOSELY FOLLOW CEMENT MANUFACTURER’S INSTRUCTIONS.
WARNING! FALLING AND TRIPPING HAZARD. THE DECK LID MUST BE INSTALLED FLUSH WITH THE DECK LEVEL.
P 877-768-2717 F 877-276-POOL [email protected] www.aquastarpoolproducts.com
DIMENSIONS AND PARTS LIST
FlowStar® Skimmer with Water Stop Face
10-7/32
5-1/2
1-1/4
12-29/32 10-1/4
Part # SKR1xx,
19-21/32
8-11/16
2
2-1/2″ Spigot x 2″ Socket x 2″ NPT
1. Skimmer Body
2. 2″ Port Plug 3. Float Assembly 4. Basket 5. Basket Rod
6. Collar 7. Lid 8. Plaster Shield 9. Weir Assembly 10. WeirClip, Qty 2
8 9
10
7 Part Numbers/Colors
6
4
SKR101 – White
5
SKR102 – Black
3
SKR103 – Lt. Gray
SKR105 – Dk. Gray
1
SKR108 – Tan
Float valve and deck lid are not NSF certified.
FlowStar® Skimmer with Water Stop Face and 9” Ultra Basket (Optional Water Bond)
Part # SKR1xx-L, SKR15xxx-L (Bonded)
~10-7/32
~5-1/2
~1-1/4 ~8-11/16
~12-29/32 ~10-1/4
~23-23/32
2
2 1/2″ SP. X 2″ SOC. X 2″ NPT
1. Deep Skimmer Body with Water Stop Face 2. 2” NPT Port Plug
9
7
8
3. Float Valve Assembly
7. Plaster Shield
4. 9`’ Ultra Skimmer Basket
8. Weir Door Assembly
5. Skimmer Collar
9. Weir Door Clips
6. Skimmer Lid
6
Part Numbers/Colors
5
4
SKR101-L – White
SKR102-L – Black
3
SKR103-L – Lt. Gray
SKR105-L – Dk. Gray
1
SKR108-L – Tan
Float valve and deck lid are not NSF certified.
FlowStar® Skimmer with Water Stop Face and Water Bond
Part # SKR15xxx
10-7/32
5-1/2
1-1/4
19-21/32
8-11/16
12-29/32 10-1/4
2
2-1/2″ Spigot x 2″ Socket x 2″ NPT
1. Skimmer Body 2. 2″ Port Plug 3. Gasket 4. Float Assembly 5. Basket 6. Basket Rod 7. Collar
8. Lid 9. Plaster Shield 10. Weir Door 11. Weir Clip, Qty 2 12. Bonding Plate Assembly
10 9 11
8
Part Numbers/Colors
7
5
SKR15101 – White
6
4
SKR15102 – Black
3
SKR15103 – Lt. Gray
1
SKR15105 – Dk. Gray
12
SKR15108 – Tan
Float valve and deck lid are not NSF certified.
P 877-768-2717 F 877-276-POOL [email protected] www.aquastarpoolproducts.com
DIMENSIONS AND PARTS LIST
FlowStar® Skimmer with Flush Face
14-15/16 10-7/32
19-21/32
1-1/4
10-3/16
7-7/16
Part # SKR2xx
2-1/2″ spigot x 2″ socket x 2″ NPT
1. Skimmer Body
2. 2″ Port Plug 3. Float Assembly 4. Basket 5. Basket Rod
6. Collar
7. Lid 8. Paster Shield 9. Weir Assembly 10. Weir Clip, Qty 2
8 9 10
7
Part Numbers/Colors
6
4
SKR201 – White
5
SKR202 – Black
3
SKR203 – Lt. Gray
2
SKR205 – Dk. Gray
1
SKR208 – Tan
Float valve and deck lid are not NSF certified.
FlowStar® Skimmer with Flush Face and 9” Ultra Basket (Optional Water Bond)
Part # SKR2xx-L SKR17xxx-L (Bonded)
~10-7/32
~4-23/32
~1-7/32
~7-31/32
~11-3/16 ~10-7/32
~23-23/32
2
2 1/2″ SP. X 2″ SOC. X 2″ NPT
1. Deep Skimmer Body 2. 2” NPT Port Plug 3. Float Valve Assembly 4. 9`’ Ultra Skimmer Basket
7 8 9
5. Skimmer Collar 6. Skimmer Lid 7. Plaster Shield 8. Weir Door Assembly 9. Weir Door Clips
6
Part Numbers/Colors
5
4
SKR201-L – White
SKR202-L – Black
3
SKR203-L – Lt. Gray
SKR205-L – Dk. Gray
SKR208-L – Tan
1
Float valve and deck lid are not NSF certified.
FlowStar® Skimmer with Flush Face and Water Bond
14-15/16 10-7/32
1-1/4
10-3/16
19-21/32
7-7/16
2
Part # SKR17xxx
2-1/2″ Spigot x 2″ Socket x 2″ NPT
1. Skimmer Body 8. Lid
2. 2″ Port Plug 9. Plaster Shield
3. Gasket
10. Weir Door
4. Float Assembly 11. Weir Clip, Qty 2
5. Basket
12. Bonding Plate Assembly
6. Basket Rod
7. Collar
10 9 11
Part Numbers/Colors
8
7
SKR17101 – White
5
6
SKR17102 – Black
4
3
SKR17103 – Lt. Gray
SKR17105 – Dk. Gray
1
SKR17108 – Tan
12
Float valve and deck lid are not NSF certified.
P 877-768-2717 F 877-276-POOL [email protected] www.aquastarpoolproducts.com
DIMENSIONS AND PARTS LIST
FlowStar® Skimmer with Flush Face 4” Extension
10-7/32
8-3/4
1-5/32
10-11/32 8-15/32
19-21/32
7-19/32 2
Part # SKR14xxx,
2-1/2″ Spigot x
2″ Socket x 2″ NPT 8
1. Skimmer Body With 6. Collar
9
4″ Extension
7. Lid
2. 2″ Port Plug
8. Weir Assembly
3. Float Assembly
9. Weir Clip, Qty 2
4. Basket
5. Basket Rod
7 Part Numbers/Colors
6
4
SKR1401 – White
5
SKR1402 – Black
3
SKR1403 – Lt. Gray
SKR1405 – Dk. Gray
SKR1408 – Tan
1
Float valve and deck lid are not NSF certified.
FlowStar® Skimmer with Flush Face 4” Extension with 9” Ultra Basket
~10-7/32
~8-3/4
~1-5/32
~10-11/32 ~8-15/32
~23-23/32
~7-19/32
2 1/2″ SP. X 2″ SOC. X 2″ NPT
8
7
9
Part # SKR14xxx-L Part # SKR32xxx-L (Bonded)
1. Deep Skimmer Body With 4″ Extension
2. 2″ NPT Port Plug 3. Float Assembly 4. 9″ Ultra Skimmer Basket
5. Skimmer Collar 6. Skimmer Lid 7. Plaster Shield 8. Weir Door Assembly 9. Weir Door Clips
6
Part Numbers/Colors
5
SKR1401-L – White
4
SKR1402-L – Black
3
SKR1403-L – Lt. Gray
2
SKR1405-L – Dk. Gray
1
SKR1408-L – Tan
Float valve and deck lid are not NSF certified.
FlowStar® Skimmer with Flush Face 4” Extension and Water Bond
10-7/32
8-3/4
1-5/32
10-11/32 8-15/32
19-21/32
7-19/32 2
2-1/2″ Spigot x
8
2″ Socket x 2″ NPT
9
1. Skimmer Body With 4″ Extension
2. 2″ Port Plug
3. Float Assembly 4. Basket 5. Basket Rod
10
6. Collar 7. Lid 8. Plaster Shield 9. Weir Assembly 10. Weir Clip, Qty 2 11. Bonding Plate Assembly
7 Part Numbers/Colors
6
4
SKR3201 – White
5
SKR3202 – Black
3
SKR3203 – Lt. Gray
SKR3205 – Dk. Gray
1
SKR3208 – Tan
11
Float valve and deck lid are not NSF certified.
P 877-768-2717 F 877-276-POOL [email protected] www.aquastarpoolproducts.com
WATER STOP FACE INSTALLATION
AquaStar’s Flow Star Skimmer with Water Stop Face provides extra protection against leaks and features 135 degree and bottom flat ledge guides for consistent mouth construction.
To install cover the outer-most flange of the water stop in gunite. Keep 135 degree and flat ledge guide exposed. Apply thin-set directly on top of the water stop 135° and flat ledge guides. Cover in thin-set and tile over if desired.
INSTALLATION DIMENSIONS
TOP VIEW
CONCRETE
18″
SIDE VIEW
1″ VERTICAL ADJUSTMENT OF FRAME TO ACCOMODATE MISALIGNMENT.
18 ”
11-1/4″ 1″
7-1/2″
TILE
20 ”
10″
18″
EARTH
TO SUCTION PUMP
ALTERNATE MAIN DRAIN LINE
2″ MIN. WATER LINE
TILE
EQUALIZER LINE
CONCRETE PLASTER
LIMITED WARRANTY
Skimmers manufactured by AquaStar are warranted to be free of defects in material and workmanship for one year from date of installation. The foregoing warranties relate to the original consumer purchaser (“Purchaser”) only. AquaStar shall have the option to repair or replace the defective product, at its sole discretion. Purchasers must pay all labor and shipping charges necessary to replace the product covered by this warranty. Requests for warranty service must be made through the installing dealer. This warranty shall not apply to any product that has been subject to negligence, misapplication, improper installation or maintenance, or other circumstances which are not in AquaStar’s direct control. This warranty sets forth AquaStar’s sole obligation and Purchaser’s exclusive remedy for defective products. AQUASTAR SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL OR CONTINGENT DAMAGES WHATSOEVER. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICABLE EXPRESS WARRANTIES PROVIDED HEREIN. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Supersedes all previous publications.
©2021 AquaStar Pool Products
Rev 052721.1
P 877-768-2717 F 877-276-POOL [email protected] www.aquastarpoolproducts.com
AquaStar Pool Products
