LA2328-2W Outdoor Wall Light
Product Information
The product is a wall-mounted light fixture called “La Plus
Belle”. The user manual provides instructions for assembling and
installing the fixture. The product is made in China.
Product Usage Instructions
Step 1: Shut off the power at the circuit
breaker box and remove the old fixture and all hardware from the
junction box.
Step 2: Fix the mounting plate D on the
junction box with the box screw. The side of the mounting plate
marked GND must face out.
Step 3: Attach the back plate (D) of the lamp
body (B) onto the junction box and lock it securely with the
mounting screw.
Step 4: Follow wiring instructions carefully.
Connect the black wire from the fixture to the black house (hot)
wire. Connect the white wire from the fixture to the white
(neutral) house wire. If your outlet box has a ground wire (green
or bare copper), connect the fixture’s ground wire to it.
Otherwise, attach the bare copper fixture wire to the green ground
screw on the mounting plate.
Step 5: Install the light bulbs (not included)
in accordance with the fixture’s specifications. DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!
Step 6: Attach the decorative bend (F) to the
siding and tighten with the mounting cap (E).
Note: To prevent moisture from entering the
outlet box and causing a short, use clear caulking (i.e.
Indoor/Outdoor Silicone Sealant) to outline the outside of fixture
back plate where it meets the wall leaving a space at bottom to
allow moisture a means to escape.
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT
BREAKER.
ATTENTION: COUPER LE COURANT AU FUSIBLE OU UN
DISJONCTEUR.
ASSEMBLING & INSTALLATION INSTRUCTIONS FIG.1
La Plus Belle
The drawing shown may not exactly match the product enclosed. However, the installation instructions do apply to this product.
To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. Indoor/Outdoor
***WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. ***ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
Silicone Sealant) to outline the outside of fixture back plate where it meets the wall leaving a space at bottom to allow moisture a means to escape.
Caulking
1.Shut off the power at the circuit breaker box. Remove old fixture
and all hardware from Junction Box. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation. 2.Fix mounting plate D on junction box with Box Screw . The side of
Mounting Screw Supply Wire
Supply Ground Wire
F E
the mounting plate marked “GND” must face out. The junction
Junction Box
box is not included.
(Not included)
3. Attach the back plate(D) of the lamp body (B) onto the junction box, and lock it securely with the Mounting Screw.
Supply Wire
B
4.Follow wiring instructions carefully.(see fig.2) 5.Attach the decorative bend (F) to the siding and tighten with the
Mounting Plate D
Box Screw
mounting cap (E) 6.Install the light bulbs(not included) in accordance with the fixture’s
Fixture Wire
specifications. NOTE: DO NOT EXCEED THE MAXIMUN
Bulb(Not included)
WATTAGE RATING!
CONNECTING THE WIRES (Fig.2) 1. Connect the electrical wires as follows. Connect the Black wire
from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise attach the bare copper fixture wire to the green ground screw on the mounting plate. 2. Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test the fixture.
FIG.2 FIXTURE WIRES Black or Smooth
HOUSE WIRES Black(Hot)
FIXTURE WIRES White or Ribbed
HOUSE WIRES White (Neutral) MADE IN CHINA
FIXTURE WIRES Bare Copper (Ground)
HOUSE WIRES Green or Bare Copper(Ground)
LA2328-2W
