Emaux Fsp350-6w Filter And Pump Combo Instruction Manual

FSP350-6W Filter and Pump Combo

Product Information: FSP350-6W / FSP400-6W / FSP450-6W /
FSP500-6W / FSP650-6W FILTER & PUMP COMBO

The FSP Filter & Pump Combo is a versatile filtration system
designed for pool water cleaning. It includes a filter tank, a
multiport valve, and a pump assembly. The system uses filter sand
media to remove dirt particles from the pool water.

Installation Instructions:

1. Ensure that the installation is performed by an approved and
   correctly rated contractor.
2. Provide a gate valve in the suction piping.
3. When connecting the pump suction and discharge, do not screw
   the pipes beyond the molded-in thread stops.
4. Loading the sand media in the filter tank and multiport valve:
   • Loosen the plastic clamps from the tank neck.
   • Cap the internal pipe with a plastic cap to prevent sand from
     entering it.
   • We recommend filling the tank approximately halfway with water
     to provide a cushion effect when pouring in the filter sand. This
     protects the under-drain laterals from excessive shock.
   • Carefully pour in the correct amount and grade of filter sand,
     ensuring that the center pipe remains centered.

Usage Instructions:

1. Ensure that the correct amount of filter media sand is in the
   tank and that all connections are secure.
2. Depress the control valve handle and rotate it to the BACKWASH
   position. Always depress the handle before turning to prevent
   damage to the control valve seal.
3. Prime and start the pump. Fill the pump with water before
   starting the motor, ensuring that all suction and return lines are
   open. This allows the filter tank to fill with water. Run the pump
   for at least 1 minute until water is flowing out of the waste line.
   This initial backwashing helps remove impurities or fine sand
   particles in the sand media.
4. Turn off the pump and set the valve to the RINSE position.
   Start the pump and operate until the water in the sight glass is
   clear, which usually takes about 1/2 to 1 minute.
5. Turn off the pump and set the valve to the FILTER position.
   Restart the pump. The filter is now operating in the normal filter
   mode, effectively removing dirt particles from the pool water.
6. Adjust the pool suction and return valves to achieve the
   desired flow.
7. Check the system and filter for water leaks and tighten
   connections, bolts, and nuts as required.

Replacement Parts of Filter:

FSP350-6W / FSP400-6W / FSP450-6W / FSP500-6W / FSP650-6W
FILTER & PUMP COMBO
Installation & Operating Instruction
INSTALLATION
* Install filtration system including pump,filter tank and multiport valve. * The filter system should be installed as close as possibie to the swimming pool and preferably at a level of 0.50 metres below the surface of the water in the swimming pool. Make sure there is drainage available at the place where the filter is to be installed. * PUMP 1) Only qualified,licensed personnel should install pump and wiring. 2) Electrical Contractors Please Note:All 220 volt 50Hz pump must be wired to the main power supply
trough an approved and correctly rated contractor. 3) Allow for gate valve in suction piping. 4) Pump suction and discharge connections have moulded in thread stops,do not try to screw pipe in
beyond these stops. * FILTER TANK and MULTIPORT VALVE 1) Loading the sand media.Filter sand media is loaded through the top opening of the filter.
a) Loosen the plastic clamps from tank neck. b) Cap internal pipe with plastic cap to prevent sand from entering it. c) We recommend filling tank approximately 1/2 way with water to provide a cushion effect when the
filter sand is poured in. This helps protect the under-drain laterals from excessive shock. d) Carefully pour in correct amount and grade of filter sand.Be sure center pipe remains centered in
opening. Sand surface should be leveled and should come to about the middle of the filter tank.Remove plastic cap from internal pipe. 2) Assemble filter control valve to filter tank. a) Insert filter control valve(with O’ring in place)into the tank neck,taking care that the center pipe slips into the hole in the bottom of the valve. b) Place two plastic clamps around valve flange and tank neck and tighten just enough so that the valve mayBe rotated on tank for final positioning. c) Carefully screw pressure gauge(with O’ring in place)into tapped hole in valve body.Do not overtighten. d)Connect pump to control valve opening marked PUMP with hose.After connections are made, tighten clamps with screwdrive,tapping around clamp with screwdrive handle to help seat valve flange clamp. 3) Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary plumbing connections,suction lines to pump,waste,etc. 4) To prevent water leakage,be sure all pipe connections are tight.
EMFS18111971
1

INSTALL/START-UP OF FILTRATION
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure. 2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always
depress handle before turning.)
3) Prime and start pump. Never tun pump dry! Running pump dry may damage seals,causing leakage and flooding!
Fill pump with water before starting motor. (be sure all suction and return lines are open), allowing the filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial backwashing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2
to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher than the initial “clean” pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control valve functions). NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually heavy initial dirt load in the water.
REPLACEMENT PARTS OF FILTER

Item

Part No.

Description

Qty

1

88280105

1.5″Top Mount Valve

1

2

89280101

1.5″ union with sight glass,O-Ring

1

3

89280102

1.5″ Union Set With O-Ring

1

06021013

Plastic Pressure Gauge With O-Ring (40psi)

1

4

01111048

Connector for pressure gauge

1

5

89030204

Hose adaptor with O-Ring

1

6

02011026

Sleeve for Hose

2

89031501

FSP350-6W Plastic Hose with Nut

1

89031601

FSP400-6W Plastic Hose with Nut

7

89031701

FSP450-6W Plastic Hose with Nut

1

1

2

1

35 6

89031801

FSP500-6W Plastic Hose with Nut

1

89031901

FSP650-6W Plastic Hose with Nut

1

8

01013049

Hose adaptor with nut

1

9

02011104

O-Ring for pump

1

08030006

SS020(220V/50Hz)

1

7

08030007

SS033(220V/50Hz)

1

08030008

SS050(220V/50Hz)

1

10

08030009

SS075(220V/50Hz)

1

4

08030010

SS100(220V/50Hz)

08030011

SS120(220V/50Hz)

11

89032001

Pump Assembly Screw

89010119

M6*50 Screws With Nut

12

01271010

Clamp Lock

1

1

2

12

2 2

13

P350

6

15

8

9

13

02011134

O-Ring for Filter Neck

01331005

P350 Filter Tank

01331006

P400 Filter tank

1

1

14

1

11

10

14

01331007

P450 Filter tank

01331008

P500 Filter tank

1 1

16

01331010

P650 Filter tank

15

89011602

P350 Lateral Assembly with Center Pipe

89011603

P400 Lateral Assembly with Center Pipe

1

17

1

1

18

89011604

P450 Lateral Assembly with Center Pipe

16

89011605

P500 Lateral Assembly with Center Pipe

1

19

1

89011606

P650 Lateral Assembly with Center Pipe

1

01172007

P400-P450 Laterals (115mm)

8

17

01172008

P500-P650 Laterals (126mm)

8

18

89011601

Water Drain Set

1

01111056

FSP350 Combo Base

1

19

01111053

FSP400-FSP650 Combo base

1

2

SS PUMP REPLACEMENT PARTS
PRIMING PUMP
Release all air from filter and piping system. In a flooded suction system (water source higher than pump), pump will prime itself when suction and discharge valves are opened. If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water. Clean and inspect Ring; re-install on trap cover. Replace trap cover on trap; turn clockwise to tighten cover. NOTICE: Tighten trap cover by hand only .Pump should prime now. Priming time will depend on vertical length of suction lift and horizontal length of suction piping.
3

VALVE REPLACEMENT PARTS

Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Part No. 01013003 03018008 01181001 89280107 01013004 02011002 01181002 03014001 02011022 01021001 02311002 E190147 02011001 02020013 01013015 02011003 01171153 01013017 01041002 01172026 89280120 89021307 06021013

Description

Qty

Handle (Big)

1

Pin for Handle

1

Washer for Handle

1

M6 x 30 Screw with Nut for Standard Lid

6

1.5″ Top/Side Mount Valve Standard Lid (Black) 1

O-Ring for 1.5″ Valve Lid

1

Washer for Spring

1

Spring for 1.5″ Top/Side Mount Valve

1

O-Ring for Valve Rotor

2

1.5″ Valve Rotor

1

Spider Gasket

1

1.5″ Body with Diffuser (Black)

1

O-Ring for Diffuser

1

O-Ring for 1.5″Connector

3

1.5″ Connector (Black)

3

O-Ring for 1.5″ Adaptor

3

1.5″ Union (A/E)(Black/White)

2

1.5″ Union Nut (Black)

3

1.5″ Union with Sight Glass (Short)

1

1.5″ Union with Sight Glass Holder(Black/White) 1

Drain Plug Fitting with O-ring

1

Drain Plug with O-ring

1

Plastic Pressure Gauge with O-ring

1

20 18 19 16 15 14 21
22 23

1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18
13

Valve Position FILTER BACKWASH RINSE WASTE RECIRCULATE CLOSED

Function Normal Filtration and Vacuuming Cleaning Filter by reversing the flow Used after backwash to flush dirt from valve By-passes filter, used for vacuuming to waste or lowering water level By-passes filter for circulating water to pool Shuts off all flow to filter or pool

WARNING
! THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE.
! TURN PUMP OFF BEFORE CHANGING VALVE POSITION. ! TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM.CLEAN PUMP
STRAINER AND SKIMMER BASKETS REGULARLY. ! DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.

4

References

• Webmail: access your OVH emails on ovhcloud.com | OVHcloud