PP-5000 MC Phono Pickup Cartridge
Product Information
Product Name: Phasemation PP-5000 MC Phono Pickup
Cartridge
Model Number: P500-1221-01
Electric Generation: Moving Coil
Impedance: 4 ohms
Appropriate Needle Pressure: 1.7 – 2.0g
Output Voltage: 0.3mV or more (1kHz 50mm/s
horizontally)
Frequency Range when Playing: 10Hz – 30kHz
Compliance: 8.5 /mN [8.5 x 10-6cm/dyne] (100Hz)
Separation: 30dB or more (1kHz)
Channel Balance: Within 1dB (1kHz)
Applicable Temperature Range: 20 – 26°C
Weight: 14.3g + 0.4
Stylus Chip: Natural Diamond
Cantilever: Synthetic %JBNPOE (Diameter 0.2mm)
Magnet: SamaliumDPCBMU
Magnetic Circuit Components Material: 1VSNFOEVS
Material of Base: Stainless (TiN treatment)
Material of Body: Duralumin (DLC treatment)
Dimensions: See Figure
Product Usage Instructions
Connection:
- The left upper terminal: Right channel Hot + (red)
- The right upper terminal: Left channel Hot + (white)
- The left lower terminal: Right channel Earth – (green)
- The right lower terminal: Left channel Earth – (blue)
Installation:
- The mounting hole of this cartridge is a through-type and it
may be pinched with the shell and screw or directly screwed to the
shell. - The recommended size of the screw is M2.6mm, P0.45mm.
Cautions:
- This cartridge is a low-impedance-moving-coil type. Please use
it with an MC low impedance step-up transformer or a head amplifier
(MC input of PHONO) in order to connect it to a phono
amplifier. - When cleaning the stylus chip, use a brush without touching the
coil or the wire and remove the dirty spots from the stylus chip.
Never use any moist cleaners when cleaning the stylus chip. It will
harm the glue and be the cause of damages. Also be sure to avoid
using solvents such as alcohol or it can cause trouble such as chip
skipping. - Do not apply heat to the cartridge directly such as soldering
the lead wire at the output terminal. It can cause trouble such as
breakage of the wire. - Use at a temperature from 20°C to 26°C. This cartridge will not
perform as well as it is designed if it is used at a temperature
out of the range. If the cartridge was stored in winter, make sure
to take enough warm-up time until the room temperature fits in the
range before using this cartridge. - When cleaning this cartridge, please use a dry clean cloth. Be
sure to avoid using solvents such as alcohol/thinner or moist
cleaners. - The included screws are made of steel for the sound quality and
strength. The included washers are made of resin to make it spin in
order to prevent over-tightening.
Needle Exchange:
When exchanging the cartridge needle, we will keep the unit and
exchange the needle-assembly. (The cartridge itself will stay as
before). When exchanging the needle, please bring the cartridge and
consult the dealer.
PP-5000
MC PHONO PICKUP CARTRIDGE
Owner’s Manual
P500-1221-01
Thank you for purchasing Phasemation PP-5000, MC phono pick up cartridge. Please read the following instructions carefully to follow the proper use of PP-5000 before setting it up in order to enjoy this product for many years.
Connection
Magnetic poles of each terminal are shown on the right.
Properly connect them in accordance with the colors of the lead wires.
The left upper terminal
: Right channel Hot + (red)
The right upper terminal
: Left channel Hot + (white)
The left lower terminal
: Right channel Earth – (green)
The right lower terminal
: Left channel Earth – (blue)
Red
White
R L
Green
Blue
Installation
The mounting hole of this cartridge is a through-type and it may be pinched with the shell and screw or directly screwed to the shell. The recommended size of the screw is M2.6mm, P0.45mm.
Cautions
1. This cartridge is a low-impedance-moving-coil type. Please use it with an MC low impedance step-up transformer or a head amplifier (MC input of PHONO) in order to connect it to a phono amplifier.
2. When cleaning the stylus chip, use a brush without touching the coil or the wire and remove the dirty spots from the stylus chip. Never use any moist cleaners when cleaning the stylus chip. It will harm the glue and be the cause of damages. Also be sure to avoid using solvents such as alcohol or it can cause trouble such as chip skipping.
3. Do not apply heat to the cartridge directly such as soldering the lead wire at the output terminal. It can cause trouble such as breakage of the wire.
4. Use at a temperature from 20 C to 26 C. This cartridge will not perform as well as it is designed if it is used at a tempertaure out of the range. If the cartridge was stored in winter, make sure to take enough warm-up time until the room temperature fits in the range before using this cartridge.
5. When cleaning this cartridge, please use a dry clean cloth. Be sure to avoid using solvents such as alcohol/thinner or moist cleaners.
6. The included screws are made of steel for the sound quality and strength. The included washers are made of resin to make it spin in order to prevent over-tightening.
12.7
Specifications
1. Electric Generation
Moving Coil
2. Impedance
4
3. Appropriate Needle Pressure 1.7 – 2.0g
4. Output Voltage
0.3mV or more (1kHz 50mm/s horizontally)
5. Freq. Range when Playing 10Hz – 30kHz
6. Compliance
8.5 /mN [8.5 x 10-6cm/dyne] (100Hz)
7. Separation
30dB or more (1kHz)
8. Channel Balance
Within 1dB (1kHz)
17
9. Applicable Temp. Range 20 – 26 C
10. Weight
14.3g + 0.4
11. Stylus Chip
Natural Diamond
(line contact / bending rate 0.03×0.003mm)
12. Cantilever
Synthetic %JBNPOE (Diameter 0.2mm)
13. Magnet
SamaliumDPCBMU
16
14. Magnetic Circuit
1VSNFOEVS
Components Material
15. Material of Base
Stainless (TiN treatment)
16. Material of Body
Duralumin (DLC treatment)
17. Dimensions
See Figure
*Dimensions and specifications are subject to change without notice due to improvements.
22
6
2
8
2.6 1.2
9.5
Figure with Dimensions (mm)
Needle Exchange
When exchanging the cartridge needle, we will keep the unit and exchange the needle-assembly.
(The cartridge itself will stay as before). When exchanging the needle, please bring the cartridge and consult the dealer.
Kyodo Denshi Engineering Co., Ltd.
8-40-17 Shinyoshidahigashi, Kohoku-ku, Yokohama, Kanagawa, 223-0058 Japan TEL 81-45-710-0975 / FAX 81-45-710-0976 / URL https://phasemation.com
RL
12
Phasemation
