093068 Charlotte Beaded Chandelier
Product Information
The Charlotte Beaded Chandelier is a stylish lighting fixture
designed to add elegance to any room. It features a brass finish
and comes with a beaded design that adds a touch of sophistication.
The chandelier is suitable for direct-wired installation and
requires an electrical junction box in the ceiling to support its
weight. The fixture weighs 43lbs (19.5kg) and should be installed
by a licensed electrician.
Key Features
- Brass finish
- Beaded design
- Direct-wired installation
- Requires an electrical junction box
- Weighs 43lbs (19.5kg)
Parts Included
- Wire Connectors (Qty: 3)
- Mounting Bracket (Qty: 1)
- Ground Screw (Qty: 1)
- Mounting Screws (Qty: 2)
- Nipple (Qty: 1)
- Hex Nut (Qty: 2)
- Lock Washer (Qty: 1)
- Canopy (Qty: 1)
- Collar Loop (Qty: 1)
- Thread Ring (Qty: 1)
- Chain (Qty: 1)
- Fixture Loop (Qty: 1)
- Candle Sleeves (Qty: 6)
Product Usage Instructions
- Before starting, ensure that the main electrical supply is shut
off from the main fuse box or circuit breaker. - Remove all the parts from the carton and keep them safe.
- Attach the Fixture Loop (P) to the threaded tube at the top of
the Fixture Body. Screw it in until tightened. - Gently pull down the existing ground (D), hot (B), and neutral
(C) junction box wires from the ceiling junction box (A) and let
them hang. - Inspect the wires on the chandelier fixture. The neutral
fixture wire is ribbed, the hot fixture wire is smooth, and the
ground wire is copper. - Connect the neutral fixture wire to the neutral junction box
wire (C) using a plastic wire connector (E). Wrap the connection
with electrical tape, ensuring no wire strands are exposed. - Connect the hot fixture wire to the hot junction box wire (B)
using a plastic wire connector (E). Wrap the connection with
electrical tape, ensuring no wire strands are exposed. Do not
reverse the hot and neutral connections. - Tuck the wire connections neatly into the ceiling outlet
junction box (A). - Attach the mounting bracket (F) to the ceiling outlet junction
box (A) using the mounting screws (H). Tighten the screws securely
with a screwdriver. - Attach one hex nut (J) to the top and the other hex nut (J) to
the bottom of the nipple (I). - Put the lock washer (K) onto the nipple (I) from the bottom,
followed by the collar loop (M), thread ring (N), and canopy
(L). - Securely tighten the hex nut (J) at the bottom of the nipple
(I) to hold all parts in place. - Attach the chain (O) to the fixture loop (P) and adjust the
length as desired. - Install the desired lightbulb(s) following the bulb
specifications mentioned in the light fixture. Note that lightbulbs
are not included. - Turn on the main electrical supply and enjoy your Charlotte
Beaded Chandelier.
Charlotte Beaded Chandelier ASSEMBLY INSTRUCTIONS
093068 NAT
IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING.
We strongly recommend that all direct-wired lighting products be installed by a licensed electrician. Two people may be required for installation. DO NOT EXCEED the rated bulb wattage. Keep flammable materials away from bulbs. This light fixture is shipped with all internal wiring intact. Do not open the product or alter the wiring in any manner.
Installation requires an electrical junction box in the ceiling sufficient to support the weight of the light fixture. This fixture weighs: 43lbs. (19.5kg).
WARNING: Be certain that the power to the electrical junction box is turned off at the circuit breaker before installation. Turning the power off at a light switch is not sufficient to prevent electrical shock. CAUTION: Prior to installation, locate All INCLUDED PARTS before disposing of packaging materials.
TOOLS REQUIRED FOR INSTALLATION
Screwdrivers Electrical Tape
Pliers Wire Connectors
Wire Cutters
Adjustable Wrench
Note: Lightbulb(s) are not included. See light fixture for bulb specification. Additional wiring supplies may be required
Parts Not Included:
Part
Qty.
A
1
B
1
C
1
D
1
Description Ceiling Outlet Junction Box Hot Junction Box Wire Neutral Junction Box Wire Ground Junction Box Wire
Parts Included (Refer to figure):
Part
Qty. Description
E
3
Wire Connectors
F
1
Mounting Bracket
G
1
Ground Screw
H
2
Mounting Screws
I
1
Nipple
J
2
Hex Nut
K
1
Lock Washer
L
1
Canopy
M
1
Collar Loop
N
1
Thread Ring
O
1
Chain
P
1
Fixture Loop
Q
6
Candle Sleeves
Page 1 of 3
©2023 Ethan Allen Global, Inc
093068 NAT Charlotte Beaded Chandelier Brass Assembly Instructions, continued
ASSEMBLY PROCEDURES: 1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER. 2. Remove all the parts from the carton. Do not throw away any parts. 3. Attach the Fixture Loop (P) to the threaded tube at the top of the Fixture Body. Screw it in until tightened.
4. Gently pull existing ground (D), Hot (B), and Neutral (C) Junction Box Wires down from the Ceiling Junction Box (A) and allow these to hang.
5. Carefully inspect the wires on the chandelier fixture. The Neutral Fixture Wire is ribbed. The Hot Fixture Wire is smooth, and the Ground Wire is copper.
6. Attach the Ground Wire from the fixture to the Ground Junction Box Wire (D); it usually has green insulation around it or is bare wire. Fasten these together with a Wire Connector (E) and wrap the connection with electrical tape. Make sure no wire strands are exposed. If your Ceiling Outlet Junction Box (A) does not have a Ground Junction Box Wire (D), insert the Ground Screw (G) into the Mounting Bracket (F) where it is marked “Ground” and wrap the bare ground wire from the chandelier around the Ground Screw (G). Tighten the screw to clamp the Ground Wire between the Ground Screw (G) head and the Mounting Bracket (F). IT IS IMPERATIVE THAT THE CEILING JUNCTION BOX (A) IN YOUR HOME BE PROPERLY GROUNDED.
7. Connect the Neutral Fixture Wire to the Neutral Junction Box Wire (C); it usually has white insulation around it. Fasten these together with a plastic Wire Connector (E) and wrap the connection with electrical tape. Make sure that no wire strands are exposed.
8. Connect the Hot Fixture Wire to Hot Junction Box Wire (B); it usually has black insulation around it. Fasten these together with a plastic Wire Connector (E) and wrap the connection with electrical tape. Make sure that no wire strands are exposed. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
9. Gently tuck the wire connections neatly into the Ceiling Outlet Junction Box (A). 10. Attach the Mounting Bracket (F) to the Ceiling Outlet Junction Box (A) using the Mounting Screws (H). Tighten
screws with a screwdriver until secure. 11. Attach one Hex Nut (J) to the top and the other Hex Nut (J) to the bottom of the Nipple (I). Put the Lock
Washer (K) in before attaching the Collar Loop (M) to the bottom end of the Nipple (I). 12. Secure the top of the Nipple (I) to the Mounting Bracket (F) with the Hex Nut (J), exposing approximately 2″ of
the thread. Then secure the Collar Loop (M) to the bottom end of the Nipple (I) with the Hex Nuts (J) and Lock Washer (K). 13. Slide the Canopy (L) and the Threaded Ring (N) up the Chain (O). 14. Place the Canopy (L) over the Ceiling Outlet Junction Box (A) and secure it in place by screwing the Threaded Ring (N) onto the Collar Loop (M). 15. Place the Candle Sleeve (Q) over the sockets of the fixture body. 16. Insert Six (6) 60-Watt maximum Type B Candelabra incandescent light bulbs (not included) or six (6) 13-watt maximum compact fluorescent light bulb (not included) or six (6) 9-watt maximum LED light bulb (not included) into the sockets. Do not exceed the specified wattage.
Page 2 of 3
©2023 Ethan Allen Global, Inc
093068 NAT Charlotte Beaded Chandelier Brass Assembly Instructions, continued
CARE INSTRUCTIONS 1. Wipe with a soft, dry cloth. 2. AVOID cleaners, harsh chemicals, scouring pads, etc. as these may cause damage to the pendant finish.
After troubleshooting, if the light fixture still does not work, contact your local Ethan Allen Design Center. SAVE THESE INSTRUCTIONS
Page 3 of 3
©2023 Ethan Allen Global, Inc
