Aroindia Sr-m 031 Ken Kou Shoe Cover Dispenser Instruction Manual

Aroindia Sr-m 031 Ken Kou Shoe Cover Dispenser Instruction Manual

AROINDIA logoOperating Instruction Manual
Ken Kou – Shoe Cover Dispenser
Model: SR-M (031) AROINDIA SR-M 031 Ken Kou Shoe Cover Dispenser

Product Introduction

The shoes film machine is very practical and has a wide range of application. It is not only suitable for families, but also widely used in hotels, real estate, hospitals, electrical; exhibition halls, dust-free workshops of factories, animal and plant breeding research sites, etc. This product does not require any power supply. Safe and reliable, exquisite shape, no need to take off shoes, easy and convenient to change the film

  1. Correct demonstration of film cuttingAROINDIA SR-M 031 Ken Kou Shoe Cover Dispenser - film cutting
  2. Shoe film Installation stepsAROINDIA SR-M 031 Ken Kou Shoe Cover Dispenser - Shoe film Step 1: Lift the cover and put it a side
    Step 2:
    Pick up a roll, align the small
    testers on both sides with the card slots on both sides of the machine and put it down (the left and right sides must be placed in the card slot)AROINDIA SR-M 031 Ken Kou Shoe Cover Dispenser - rough seabedStep 3: Put the shoes out and spread them evenly on the rough seabed.
    Note: the glued side of the shoes faces up, and the non -finished side sticks to the sponge pad, so that the most precious scroll cover will stick to it cover.
  3. Shoe film machine using steps
    Step 4:
    Frist use one foot to step on the paved shoe film with a little force, pull the foot that is stuck to the toe back, and pull it to the black cover of the reartraining (be careful not to cast too long, so as not cut it) set is the best way to stick to the machine and push it down a little bit, and it will be changed and cut off

AROINDIA SR-M 031 Ken Kou Shoe Cover Dispenser - Shoe film machine

Precautions of use

In order for you to use this product better, please use it according to the following precautions:

  1. When installing the shoe film, put the glued side up, and the non-stick side look at the sponge pad on one side, don’t reverse it, so that it can stick to the sole.
  2. When sticking the shoe film, pull it back slowly, and the length of the shoe should not exceed pass the black pedal so as not to effect the cutting film.
  3. Because the film cutting blade is sharp, don’t touch it with your hands, and be careful not to let children hold it.

After-Sales Service
Every shoe film machine of our company has been strictly tested and generally will not fail. If there is a problem with the during use , you can also contact our company directly, it best to avoid damage to the machine.

Specification:

Product size60x26x8cm (23.62*10.24*3.15inch)
Product weight2.65kg (5.84lb)
Place of usehome/hotel/office building, etc.
Working methodpedal type
Product materialABS plastic
Product featureseasy to use, no space
Shoe mold sizelength 90m*width 15cm (35.43*5.91inch) (outer diameter of shoe mold roll 10cm/3.94inch)
Applicable maximum shoe sizeUS shoe size 11/China shoe size 47 (length 28.5cm/11.22inch)

Aroindia Electromech Pvt Ltd.
Address: A-117, 1st Floor, Near Metro Pillar -783, Sewak Park
Dwarka Mor, New Delhi – 110059
Phone: +91 9818366017, 9599591802
E-mail: [email protected]
www.aroindia.com

References

Documents / Resouces

Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.


Related Manuals