JF4025X-WX Wireless Fast Chargingpad
Product Information
The Wireless Fast Charging Pad is a device that enables wireless
charging for mobile phones. It has an output of 10+5W and can be
mounted on magnetic surfaces or permanently mounted using built-in
screw holes. This device complies with Part 15 of the FCC Rules and
is made by Ningbo Weijia Electronics Technology Co., Ltd. in
China.
Product Usage Instructions
- Place the Wireless Fast Charging Pad on a flat surface.
- If you want to mount it on a magnetic surface, attach the
magnet (B) to the back of the pad and then stick it onto the
surface. - If you want to permanently mount it, use the built-in screw
holes to attach it to the surface. - Connect the device to a power source using the TYPE-C cable
(E). - Place your mobile phone on the mobile phone support (D) with
the screen facing up and make sure it is aligned with the charge
coil (C). - The indicator light (A) will turn on to show that the phone is
charging. - If you want to charge wireless series lights, place them on the
pad as well.
Note: To ensure compliance with FCC/IC RF exposure requirements,
maintain a separation distance of 20 cm or more between the antenna
of this device and persons during device operation.
WIRELESS FAST CHARGING PAD USER MANUAL
Supplied Accessories: · FCC ID:2BAZE-JF2117 · REF : JF2117 · Input5-12VDC, 20W
OutputMax. 10+5W
Features: · Charges two devices simultaneously · Works with compatible mobile phones · IK08 shock resistance · Strong magnets on the rear allow for easy
mounting on magnetic surfaces as well as built-in screw holes for permanent mounting
Specifications: · Material:
Ultra tough nylon, Aluminium,Rubber , PC& TPE · If charging by wireless pad: Charging time: Approx 3.0-8.0 hours depending on battery pack – the environmental temperature will affect the charging and discharging period of the battery · Operating temperature: -5°C to +30°C · Charging pad measurements: 265 x 110 x 29 mm · Net weight: 330g (packaging not included)
Disposal and environmental protection · Do not dispose of charging pad with domestic
waste · Please check with local recycling plants for the
best way to recycle · This charging pad contains substances that may
be harmful to the environment and humans if disposed of inappropriately
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1Reorient or relocate the receiving antenna. 2Increase the separation between the equipment and receiver. 3Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4Consult the dealer or an experienced radio/ TV technician for help.
MPE caution To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.
Ningbo Weijia Electronics Technology Co., Ltd.
Made in China
JF2117
WIRELESS FAST CHARGING PAD USER MANUAL
How to use the lamp ?
A: Indicator light
B: Magnet
C: Charge coil
D: Mobile phone support E: TYPE-C F: Magnet G: hanging hole
1 Wireless fast charging pads can be sucked onto iron plates 2 Wireless series lights can be charged 3 Support to charge your cell phones(induction charging allowed).
Ningbo Weijia Electronics Technology Co., Ltd.
Made in China
JF2117
