2835 220V High Voltage Led Strip
Product Information
The High Voltage LED Strip is a lighting product designed to
provide bright and efficient illumination. It is suitable for
various applications, including indoor and outdoor use. The strip
is powered by high voltage and offers excellent durability and
flexibility.
Product Usage Instructions
- Before installing the light strip, ensure that the power is
switched off to prevent any accidents or electrical shocks. - If you need to cut the strip to fit a specific length,
carefully cut it along the designated cutting line at the back of
the strip. Take caution not to damage the LED bulbs or other
components. - After cutting, seal the newly cut ends with end-caps and glue.
This will protect the strip from moisture and ensure proper
functionality. - Insert the pins of the power cable into the head end of the
strip, ensuring that they make good contact with the strip pads. It
is crucial to connect the power cable to the correct end of the
strip; otherwise, the strip will not work even when powered
up. - Securely fasten the lid to ensure that the strip remains in
place and does not fall off. - Use brackets or clips with screws to fix the strip in the
desired position. This will provide additional support and
stability. - Finally, connect the power cord to a power source to start
using the LED strip for your lighting needs.
If you have any further questions or require assistance, please
contact the importer, Prima Group 2004 LTD, in Bulgaria at the
following address: 1784 Sofia, Mladost 1, bl. 144, Ground Floor;
Phone: +359 2 988 45 72.
USER MANUAL
HIGH VOLTAGE LED STRIP
1. Please switch off the power before installation. Do not cut, connect or install the strip light when the power is on. 2. Please don’t plug in the LED strips to power more than one minute when thestrips are in a roll, as heat concentrated will cause safety accident. 3. LED strips should be cut at the point printed with the mark of scissors.Never cut the led strips at any other point to avoid damage which willmake the strips unable to work. During the cutting, make sure the cuttingpoint is vertical to the strip, never tilt it. 4. When install the strips, Please follow the instruction provided by usstrictly. 5. To avoid safety accident, don’t plug in the strips to power during installation. 6. When install and fix the strips, please don’t use metal material to lockthe strip, as metal material will easily cause short circuit, which will causesafety accident and damage the strips. 7. Please do not fold or twist the strip light during installation. The maximum bending angle of the strip is 70°, so do not bend it to 90°. 8. lf you find the strips damaged or some LEDs cannot work, just cut offthis unit to avoid safety accident. 9. Strips cannot be installed in the inflammable and explosive environment,the environment should be ventilated waterproof, moistureproof andanti-corrosion. Please don’t use anything to encase and cover the strip to ensure good heat dissipation. 10. The strips must be used together with our company’s special controllersor current DC power supply, and cannot be plugged in AC current directly,otherwise it could cause damage of the product. 11. The strips has both positive pole and negative pole. Attentions must bepaid when connect LED strips to the power. lf connected to the wrong pole.the LED strips will not work, then you have to correct it immediately, otherwise it will cause damage of the product. 12. Only the strip part is IP65, not the power adapter. The connection between the power supply and the strip light and the end-caps needs to take a waterproof adhesive before it can be used in outdoor environments. 13. Only strips with the same standard and same applying voltage can beconnected, the length of connection cannot over the max usage length,otherwise it could bring danger and burn the strip. 14. The strips is easy to cause children’ attention, please install them tothe place where children can not touch.
Installation:
1. Please make sure switch off power before installing the light strip.
2. If you need to cut the strip, please cut it along the cutting line at the back of the strip.
3. The newly cut ends need to be sealed with end-caps and glue.
4. Insert the pins of the power cable into the head end of the strip and ensure that the pins contact with the strip pads well. (If the other end of the strip inserted into the pins, the strip won’t work even power up).
5. Fasten the lid firmly to avoid the strip falling off.
6. Fix the strip with brackets or clips with screw to the position where it will be used
7. Connect the power cord to power for use. IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144, Ground Floor; Phone: +359 2 988 45 72;
