Wireless Towing Interface
Wireless Towing Interface
Operation & Installation Guide
Australia’s Most Advanced Anti-Theft System for Caravans and
Trailers
Warnings & Safety Instructions
Do not operate WiTi unless you have read and understood this
manual and WiTi is installed as per the instructions.
WiTi Wireless Towing Interface
WiTi replaces the cables connecting a tow vehicle and trailer or
caravan with an advanced Wireless Towing Interface. WiTi transmits
all lighting and braking signals from the tow vehicle to the
caravan or trailer wirelessly. WiTi complies with Australian Design
Rules when installed as directed.
WiTi Wireless Towing Interface supports CanBus vehicles and
vehicles with advanced electronics. WiTi supports vehicle specific
towing modes and features for example, disabling reverse sensors
when hitched. These features will be enabled when the WiTi Wireless
Towing Interface is in range and paired with the WiTi Anti Theft
unit in the caravan or trailer. Please refer to your vehicle hand
book for vehicle specific towing modes.
WiTi supports all third party electric brake controllers as well
as the WiTi Wireless Electric Brake Controller (sold
separately).
Note: Transmission of lighting signals is disabled when the
alarm is activated on the trailer.
Specification
- Nominal System Voltage: 12V
- Operating Voltage: 9V – 15V
- Operating Current: 38mA
- Standby Current – low power mode: 2mA
- Operating Temperature: -20C – 60C
- FCC ID: 2AC7Z-ESP32
- Weight: 120g
Installation
The wiring on the 12 pin socket on the tow vehicle must follow
Australian wiring guidelines as shown below:
| Pin No. | Circuit | Colour |
|---|---|---|
| 1 | Left-hand turn | Yellow |
| 2 | Reversing signal | Black |
| 3 | Earth return | White |
| 4 | Right-hand turn | Green |
| 5 | Service brakes | Blue |
| 6 | Stop lamps | Red |
| 7 | Rear lamps, clearance & Brown side marker lamps | |
| 8 | Battery charger / winch | Orange |
| 9 | Auxiliaries / Ignition Feed | Pink |
| 10 | Earth return | White |
| 11 | Not used | Grey |
| 12 | Not used | Violet |
WiTi Wireless Towing Interface and Communication Module
Indicator Lights:
There are two LEDs embedded in the WiTi Logo on the Wireless
Towing Interface. When the unit is powered LED 1 (Amber) will
illuminate. When the unit is paired and linked then LED 2 (Red)
will illuminate.
Pairing a new WiTi Wireless Towing Interface and Communication
Module
- Ensure the WiTi Wireless Towing Interface is plugged in and
powered on (LED 1 is lit) and in range of each other – within 10
meters. - On the WiTi Wireless Towing Interface unit press and hold the
PAIR Button. - Whilst still depressing the PAIR button, press the RESET Button
for half a second and then let go of the RESET button. - When the RESET button is released, you will notice LED2
flashing rapidly while LED 1 is still solid. Let go of the PAIR
button. The WiTi Wireless Towing Interface is now in PAIRING mode.
The unit will stay in pairing mode for five minutes while searching
for the Anti-Theft System. - Repeat the Pairing Process on the Anti-theft in the Caravan or
Trailer. - On successful pairing the WiTi LEDs will flash simultaneously
for 5 seconds on both units to indicate that they have successfully
paired with each other. Once the LED’s stop flashing both units
will exit PAIRING Mode and return to normal operation. Both LED1
and LED2 will now be illuminated when they are in range and
powered.
Wireless Towing Interface
Operation & Installation Guide
Australia’s Most Advanced Anti-Theft System for Caravans and Trailers
Warnings & Safety Instructions
Do not operate WiTi unless you have read and understood this manual and WiTi is installed as per the instructions.
· WiTi Wireless Towing Interface requires WiTi Anti-Theft to be installed in the caravan or trailer
· WiTi automatically pairs when in range but it is always good practice to check the lights before towing to ensure they are all operating.
WiTi Wireless Towing Interface
WiTi replaces the cables connecting a tow vehicle and trailer or caravan with an advanced Wireless Towing Interface. WiTi transmits all lighting and braking signals from the tow vehicle to the caravan or trailer wirelessly. WiTi complies with Australian Design Rules when installed as directed.
WiTi Wireless Towing Interface supports CanBus vehicles and vehicles with advanced electronics. WiTi supports vehicle specific towing modes and features for example, disabling reverse sensors when hitched. These features will be enabled when the WiTi Wireless Towing Interface is in range and paired with the WiTi Anti Theft unit in the caravan or trailer. Please refer to your vehicle hand book for vehicle specific towing modes.
WiTi supports all third party electric brake controllers as well as the WiTi Wireless Electric Brake Controller (sold separately).
Note: Transmission of lighting signals is disabled when the alarm is activated on the trailer.
Specification
Nominal System Voltage Operating Voltage Operating Current Standby Current – low power mode Operating Temperature FCC ID Weight
12V 9V – 15V 38mA 2mA -20C – 60C 2AC7Z-ESP32 120g
2
Contents 1. WiTi Wireless Towing Interface
Installation
The wiring on the 12 pin socket on the tow vehicle must follow Australian wiring guidelines as shown below:
Pin No. Circuit
Colour
1 Left-hand turn
Yellow
2 Reversing signal
Black
3 Earth return
White
4 Right-hand turn
Green
5 Service brakes
Blue
6 Stop lamps
Red
7 Rear lamps, clearance & Brown side marker lamps
8 Battery charger / winch Orange
9 Auxiliaries / Ignition Feed Pink
10 Earth return
White
11 Not used
Grey
12 Not used
Violet
12 11 10 9 8
4723561
WiTi Wireless Towing Interface
8 9 10 11 12
1653274
12 Pin Socket
3
Pin 8 must be connected to a permanent power supply from the battery in the tow vehicle. It does not have to be a high current supply as the WiTi Wireless Interface will draw very little current. Pin 9 is optional and can be connected to an ignition source in the tow vehicle. This circuit works in conjunction with the ignition output on the Anti-Theft unit. When the units are paired and the ignition is on in the tow vehicle then the ignition output on the Anti-Theft Unit will provide 12V. The best way to describe this is as a wireless relay. This connection can be used for any device on the caravan that requires an ignition trigger for example, a DCDC charger device in the caravan. This circuit is optional and does not have to be connected if you are not using the ignition output on the Anti-Theft Unit. NB. Not all vehicles are wired to Australian Standard VSB1 section 14 please test Pin 8 is 12V+ and Pin 9 is Ignition 12V+ before installing WiTi. To operate simply plug the WiTi Wireless Towing Interface into the 12 pin socket on the tow vehicle.
4
WiTi Wireless Towing Interface and Communication Module Indicator Lights
There are two LEDs embedded in the WiTi Logo on the Wireless Towing Interface.
When the unit is powered LED 1 (Amber) will illuminate. When the unit is paired and linked then LED 2 (Red) will illuminate.
Pairing a new WiTi Wireless Towing Interface and Communication Module
Ensure the WiTi Wireless Towing Interface is plugged in and powered on (LED 1 is lit) and in range of each other – within 10 meters.
On the WiTi Wireless Towing Interface unit press and hold the “PAIR” Button.
Whilst still depressing the “PAIR” button, press the RESET Button for half a second and then let go of the RESET button.
When the RESET button is released, you will notice LED2 flashing rapidly while LED 1 is still solid. Let go of the PAIR button. The WiTi Wireless Towing Interface is now in PAIRING mode. The unit will stay in pairing mode for five minutes while searching for the Anti-Theft System.
Repeat the Pairing Process on the Anti-theft in the Caravan or Trailer.
On successful pairing the WiTi LEDs will flash simultaneously for 5 seconds on both units to indicate that they have successfully paired with each other. Once the LED’s stop flashing both units will exit PAIRING Mode and return to normal operation. Both LED1 and LED2 will now be illuminated when they are in range and powered.
If either unit did not detect a PAIRING partner during the pairing sequence, then LED 1 and LED 2 will flash in an alternating sequence for 5 seconds (LED1-LED2LED1- LED2) this indicates that pairing has failed and the unit will then return to normal operation mode with just LED 1 illuminated. Repeat the pairing process.
5
Operation Guide
WiTi Wireless Towing Interface replaces the traditional cables between a tow vehicle and caravan / trailer with an advanced wireless connection. WiTi transmits all lighting and braking signals using the latest WiFi technologies for fast, secure and stable communication. Although wireless, WiTi is not dependant upon the Internet and communication is point to point between the vehicle unit and trailer unit. The signal is also encrypted for security and other wireless devices will not interfere with the WiTi Wireless Towing Interface (mobile phones, bluetooth, wifi devices, etc.)
No more cables to damage or rip out, no more corroded terminals and no more loose connections.
Low Power Mode
WiTi Wireless Towing Interface will enter low power mode if there is inactivity for 24 hours. In this mode power draw is less than 2 milliAmps. WiTi will exit Low Power Mode when it detects an input from the driving light circuit.
Limited Warranty
If Leisure Technologies determines that you are covered by a warranty as set in the Australian consumer law the company shall at its expense: (a) repair the product or replace the product with a new unit (which may have used refurbished parts of similar quality); (b) ship the repaired or replaced unit back to you; (c) warrant the repaired or replaced product for a reasonable period; and/or (d) refund money paid for the product. The Company has the discretion as to which remedy applies.
Warranty period The warranty period starts on the date of purchase and ends 24 months later. For the purpose of this limited warranty, the date of purchase is the date indicated on the original bill of sale or receipted invoice for the product from the vendor from which you acquired this product.
How to get warranty service During the warranty period, if you wish to return a defective product you may contact us via www. witi.com.au. You may then return the defective product to the address given accompanied by an acceptable proof of purchase (a bill of sale or receipted invoice).
What is not covered
The limited warranty does not cover a product:
·
for which you are not the original purchaser;
·
that is damaged by using in a way that was unreasonable or unintended;
·
that is returned after the applicable warranty period set out above has expired;
·
that has been installed other than per the product installation guidelines;
·
6
that has been maintained, altered or modified, opened or repaired, other than by the company or by a company authorised service centre;
·
that has been physically damaged, other than by the company or a company authorised
service centre.
·
To the extent permitted by law, Leisure Technologies, its directors, officers, employees,
suppliers and agents, shall not be liable for injury to persons or property, or for any indirect,
special, incidental or consequential, punitive or exemplary damages and liability and shall
be limited to the amount you paid for the product.
Disclaimer
·
WiTi products are designed for installation by reasonably competent consumers.
Consumers are taken to have sufficient knowledge of the intended caravan or trailer unit
and its appropriateness for the installation of any WiTi products.
·
Installation of WiTi products may require consumers to have knowledge and experience
using powered tools and electrical wiring. Consumers without such knowledge are to
refrain from attempting any installation of WiTi products and to consult their nearest WiTi
specialist or qualified Auto Electrician.
·
Prior to the installation of any WiTi product consumers are taken to have comprehensively
read and understood the appropriate WiTi operation and installation guide included with
the product.
·
It is the consumer’s sole responsibility to have WiTi products properly installed on their
vehicle and/or trailer units along with any modifications necessary for the proper
installation of WiTi products.
·
Consumers are solely and completely responsible for evaluating their trailer units to ensure
that the trailer units, and each part thereof, is appropriate, adapted and applicable for
installation and use of WiTi products.
·
Any and all WiTi unit damages caused by a consumer’s failure to modify the caravan or
trailer properly for installation and use of one or more WiTi products not covered by this
disclaimer is the sole responsibility of the consumer.
·
Leisure Technologies Pty Ltd and their distributors and resellers also expressly disclaims
all liability for direct, indirect, special, incidental, or consequential damages, including but
not limited to, damage or loss of property or equipment, injury to person whether physical
or not, loss of profits or revenue, cost of purchase or replacement of goods, or claims of
customers of the purchaser that result from the incorrect installation of any WiTi Anti-Theft
unit or subunit.
Other important notices To the extent permitted by law, this limited warranty constitutes the entire agreement on the subject matter and supersedes any prior agreement or understanding, written or oral. Where used herein, the company shall mean Leisure Technologies Pty Ltd and its subsidiaries and associates.
Our goods come with guarantees that cannot be excluded under the Australian consumer law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits under your warranty are in addition to other rights and remedies under the law in relation to the product.
7
Scan to discover more
8
witi.com.au
WiTi Anti-Theft, Wireless Towing, Wireless Brake Controller
