750 Luma Glow LED Lights
Product Information:
The Luma Glow LED Lights are a bathroomware product designed and
manufactured by Newtech. These lights are intended to create a back
lighting effect under a vanity or mirror cabinet. The lights come
in various models with different lengths and wattages, allowing
customers to choose the one that best suits their needs. The lights
are equipped with a transformer that can be plugged into an
isolating power socket or hardwired in with an isolating switch. It
is recommended to have a registered electrician install the lights
to ensure compliance with wiring regulations and safety
standards.
Product Usage Instructions:
To install the Luma Glow LED Lights, follow these steps:
- Remove the end caps of the lights.
- Press lightly on the inside of the translucent cover to remove
it. - Choose the appropriate mounting location on the under face of
the cabinet (vanity or mirror) as close to the wall as possible for
the best effect. - If necessary, mount the transformer inside the cabinet away
from the contact area. - Use recommended screws (4g x 16mm) to secure the aluminum
extrusion and avoid damage to the translucent cover channel. - If using a power socket, plug the Luma-Glow transformer into an
isolating power socket located inside the cabinet. - If hardwiring, ensure that it is wired in with an isolating
switch by a registered electrician.
Note: It is important to comply with all
relevant Australian/New Zealand Standards (AS/NZS) and wiring
regulations when installing the Luma Glow LED Lights. Newtech
recommends having a licensed and registered tradesperson carry out
the installation. Newtech cannot be held responsible for any issues
arising from the installation and use of the lights not carried out
in accordance with these instructions or for materials not supplied
by Newtech.
BATHROOMWARE DESIGN & INNOVATION
Head Office & Distribution Warehouse | 30 Mill Road, Wanganui Phone: 06 349 0194 or 0800 728 662, [email protected]
Auckland Concept Showroom | 525 Great South Road, Penrose, Auckland Phone: 09 930 6200, [email protected]
newtech.co.nz
Installation Instructions
Luma Glow LED Lights
Remove end caps and press lightly on inside of translucent cover to remove it.
Newtech recommends that a registered electrician install this product and that it is installed to the current wiring regulations and in particular to those regulations that include the installation of appliances and accessories in damp environments such as bathrooms. It must be installed in accordance with relevant Australian/New Zealand Standards (AS/NZS).
This electrical appliance is intended to create a back lighting effect under a vanity or mirror cabinet.
ELECTRICAL
The Luma-Glow transformer is designed to be plugged into an isolating power socket located inside the cabinet. If the Luma-Glow is going to be hard wired in, it must be wired in with an isolating switch by a registered electrician.
MOUNTING
The Luma-Glow should be mounted on the under face of cabinet (vanity or mirror) as close to the wall as possible to get best effect. The transformer is best mounted inside the cabinet away from contact area. Recommended screw for aluminum extrusion is 4g x 16mm to avoid damage to translucent cover channel.
SPECIFICATIONS & DIMENSIONS
Model 750 900 1200 1500 1800
Length (mm) 700 850 1150 1450 1750
Width (mm) 16 16 16 16 16
Lumens 670 820 1100 1400 1680
Wattage 5W 6.1W 8.3W 10.5W 12.6W
Figure 1.0
Drill Ø3mm hole approx 100mm from each end of Luma-Glow in middle of upper flat face
Figure 2.0 Drill Ø8mm hole through bottom of cabinet to thread wires and locate wiring grommet.
INSTALLATION
· Remove translucent cover from extrusion (see Figure 1.0)
· Drill holes to suit screw being used. Recommended 4g x 16mm (see Figure 2.0)
· Mark and drill Ø8mm hole in bottom of cabinet for wires to thread through. Hole location needs to take into account any back panel in the cabinet. The white wiring grommet should locate into this hole (see Figure 3.0)
· Remove Luma-Glow wiring from transformer, fit Luma-Glow in place under cabinet. Fit transformer in cabinet. Reconnect Luma-Glow wires to transformer, taking into account the positive and negative terminals. Pin or tape wires to avoid any entanglement.
· Refit the Luma-Glow translucent cover by squeezing back into extrusion channels
Figure 3.0
Disclaimer: Products in these installation instructions must by regulation be installed by a licensed and registered tradesperson. Newtech cannot be held responsible if the installation and use of the towel rails is not carried out in accordance with these instructions or for materials not supplied by Newtech. The manufacturer/distributor reserves the right to vary specifications without prior notification.
Newtech | Innovative Bathroomware Products & Design in New Zealand
