Mixcder X1 Tws Bluetooth Earphones User Manual

mixcder X1 TWS Bluetooth Earphones

For more information, please visit our official website www.mixcder.com
Your valuable comments and suggestions on improving Mixed er products are welcome!

Product Overview

Package Contents

-1 x Pair of Wireless Earphones -1 x Charging Case -1 x Type-C Cable -1 x User Manual

Charging

Prior to the first use, please make sure both the earphones and charging case are fully charged.

Charge the Charging Case
Please use the supplied charging cable to connect the charging case to a charger or PC to charge. While charging, the lED digital display will show the current battery capacity.

Charge the Earphones
Put the earphones back into the charging case, and the earphones will power off and be charged automatically. During charging, the earphone LEO 1urns solid red; after fully charged, LED turns off. When the battery is low, the LED indicator flash red.

Operating Instructions

Pairing Single Earphone with Your Device

1. Take out the L or R earphone from the charging case, tt will automa1ically power on (LED flashes Red and Blue alternately).
2. Turn on the Bluetooth on your device and choose Mlxcder X1 1o pair. The LED turns off when the earphone pairs with the device.

Pairing the L&R Earphones with Your Device

1. Take out the L&R earphones from the charging case, and they will automatically power on (LED flashes Red and Blue alternately) and pair with each other.
2. Once they are successfully paired with each other, LED of one earphone goes off and the other flashes Red and Blue alternately.
3. Please tum on the Bluetooth on your device and choose Mixcder X1 to pair. The LED tums off when the earphones pair with the device.
   Note: If you have previously paired the earphones with a device, they will reconnect with the 4. device automatically when you tum them on.

Control Instructions

Safety Precautions

Mixcder X1 are of excellen1 quality, and in order to extend its lifespan, please refer to the instructions below:

1. Please keep the earphones out of extreme heat, humility, and a corrosion environment.
2. Please prevent the earphones from being struck, falling, warped, soaked, etc.
3. Please don1 dismantle the earphones or the charging case.
4. Please don, overcharge the earphones for quite a long time, otherwise, It will decrease lifespan.
5.  Please use DC5V/500mA chargers/adapters certified by a regulated manufacturer.
6. Please stop using the earphones if it causes any discomfort or pain.

Troubleshooting

Q: What to do if the earphones crash?
A: Please put them back into the charging case and then take them out. Touch and hold the touch control for about Bs.

Q: What if the earphones doest work properly?
A: Please put them into the charging case and 1hen take them out Touch Lor R earphones twice, and the earphone will enter the pairing mace again.

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the uses authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hannful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radiofTV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Specifications

Warranty

The MixcderX1 is covered by a 1-year manufacturer warranty. For more information, visit: www.mixcder.com