Lasko 754201 Electric Ceramic Space Heater
Specifications
- BRAND: Lasko
- SPECIAL FEATURE: Manual
- COLOR: Dark Gray
- FORM FACTOR: Tabletop
- INDOOR/OUTDOOR USAGE: Indoor
- MODEL: 754201
- SPEEDS / SETTINGS: 2 heat setting, plus fan only
- THERMOSTAT: Adjustable thermostat
- POWER / WATTS: 1500 / 900
- CORD LENGTH: 8 ft.
- HEIGHT:2 in.
- ITEM WEIGHT:93 Pounds
- HEAT OUTPUT: 1500 Watts
- PRODUCT DIMENSIONS: 6″D x 7″W x 9.2″H
Introduction
You can pick how much heat you want with the Lasko Ceramic Space Heater with Thermostat and Tip Switch’s high and low heat settings as well as the fan-only mode. You can keep your desired temperature setting with the changeable thermostat, making it ideal for your busy home office or other living space. This heater is an excellent option for virtually any place that needs some additional warmth because it is small and appropriately proportioned for tabletop or floor use. This space heater has a tip-over switch, a cool-touch exterior, and overheat protection because it was made with safety in mind. Additionally, the heater has a handy carry handle for convenience. The heater may be put exactly where it is needed and yet be directly plugged in thanks to the 8-foot cord.
WARNING
- Plug heaters directly into a 120v wall outlet/receptacle only. Never use with an extension cord. Do not plug heater into any other cord connected device, such as a power strip, surge protector, multiple outlet
- Adapter, cord reel or outlet-type air freshener. The use of such devices may create a fire hazard. Do not plug multiple devices in the same outlet or on same circuit as heater.
- faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug fits tightly into outlet before each use. During use, check to make certain the heater plug is not overheating. If necessarily have a qualified electrician check and/or replace the wall outlet. Do not use this heater with any solid-state speed control devices.
- Make certain that the power source conforms to the electrical requirements of the Heater.
- Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended. Never leave children unattended when the Heater is on or plugged in.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
- DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.
- Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
- Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
- Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
- Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the Heater. Always unplug the power cord.
CAUTION
- Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
- This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
- This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
NEVER locate a Heater where it may fall into a bathtub or other water container.
- DO NOT use Heater outdoors.
- This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings.
THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
- This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
PARTS INCLUDED
CONTROLS
HEAT SETTINGS
Turn the Power Knob to the desired setting.
(
) – Fan Only (NO HEAT)
- Low Heat
- for High Heat (1500 Watts)
- OFF
THERMOSTAT
- Allow the Heater to warm up the room before setting the thermostat.
- To adjust the thermostat, turn the Thermostat Knob towards the (+) to increase the desired temperature and towards the (-) to decrease the desired temperature.
- When the desired temperature is reached, lower the thermostat until the Unit shuts off. This is done by turning the Thermostat Knob towards the (-).
- The Heater will now automatically maintain the set temperature by cycling the unit on and off. To prevent the Heater from cycling, adjust the thermostat.
SAFETY FEATURE
- A Tip-Over Switch is built in to prevent operation if the Heater is tipped over.
- A thermal overload protector is built in to prevent overheating.
- If an overheat temperature is reached, the Heater will automatically shut off. It can only resume operation when the user resets the unit.
TO RESET HEATER:
- Unplug the Heater and wait 10 minutes for the Heater to cool down.
- After the Heater has cooled down, plug the unit into a 120V~ electrical outlet and follow the operation instructions described in this manual.
TROUBLESHOOTING TIPS
If your Heater shuts off unexpectedly or fails to operate, the previously mentioned safety feature may have been activated to prevent overheating.
- Be sure the power cord is plugged into a working electrical outlet.
- Check your Temperature setting. The Heater may be off because it has reached the desired temperature setting.
- If your Heater runs for several minutes and shuts off repeatedly, your Heater may require cleaning. See Maintenance section below.
SERVICING: For servicing, other than general user maintenance, please contact Customer Service at (800) 233-0268, Monday through Friday, from 8am-5pm Eastern.
STORAGE: Store the Heater with these instructions in the original carton in a cool, dry place.
DISPOSITION: Corrugated packaging materials are recyclable. For environmentally responsible disposal of this product, contact your local waste service provider or visit www.1800recycling.com.
FAQs
If it’s on carpet, it will not work. I had to put a small board underneath of mine when it’s on my carpet to get the button to press in. Any other hard floor surface works fine.
I’ve found the thermostat inconvenient. At the very lowest setting, it turns on at about 59° and off at about 65°.
Divide the wattage by 120 and you will have the amps.
No, no filter. It does have to be plugged directly into the wall outlet though. You cannot use an extension cord or a surge protector.
We never looked into getting a replacement know. By the time it broke it was already like 14 years old.
We have one in each bedroom that are approx. 13 x 13 feet and it warms up nicely if door kept closed. I also have one in my bathroom which is 6 x 9 and after heating up, I turn it down low because too warm.
If the heater noted here reaches the temperature setting you have desired on the unit, it will cycle itself on and off automatically. If the unit shuts off due to overheating or blockage of airflow, the unit would need to be manually turned back on if the safety feature is engaged.
China.
I measured the cord to be 8 feet. The unit is working well.
The heater has a handle built into the back of it. I am using it in my master bathroom and it is very powerful. Great little heater.
For safety reasons, this unit should not be used in wet or damp locations. It is not rated for bathroom use because the internal components are not sealed and the plug is not grounded. If you want a heater that is approved for bathroom use, we recommend checking out the Lasko CD08200.
In addition to the surface level being flat, it also must be solid for the tip switch to work. Please try relocating the product to a different area/surface to see if that helps to resolve the issue.
Yes, there is. If you check the left turn knob, it starts with 0, then next to 0, shows a little fan, then numbers 1 and 2. So, turn the left knob to the 0 position. That turns it off. The red light will stay on because there’s power connected to it. Just like all appliances.
The 754201 draws 12.5 amps on HIGH and 7.5 amps on LOW.
All four have the same watt ratings, so likely all will heat the same.
