RunFree Lite Open Ear Headphones
User Manual
Pairing
- Long Press the power button for 3 seconds to turn on the headset. After the white light is on once, the headset enters the pairing mode, and the red and white lights flash alternately.
- Turn on the bluetooth of your device, then select“SOUNDPEATS RunFree Lite” from the bluetooth list to complete the pairing.
Reset
- Please insert the charging cable into the charging port to make the headset enter the charging status.
- Long press the power button for 3 seconds, the red and white lights will fash alternately twice, a total of 4 seconds to restore factory settings.
- Unplug the charging cable and turn it on, the headset reset is complete.
Wearing
- Identifty the left and rightearphones and wear .
- Rotate the headset and find the most comfortable position.
Product Diagram
Control
| Power on | Manually: Long Press the power button for 3 seconds when the headset is turned off |
| Power Off | Automatically: No device connection for 3 minutes, the headset will automatically shut down Manually: Long Press the power button for 3 seconds when the headset is turned on |
| Play/Pause | Short press the power button |
| Volume- | Short press the volume “-” button |
| Volume+ | Short press the volume “+” button |
| Play Previous | Long press the volume “-” button |
| Play Next | Long press the volume “+” button |
| Enter/Exit Game Mode | Triple tap the power button |
| Answer/Hang up phone call | Short press the power button |
| Reject phone call | Long press the power button for 1.5 seconds |
| Switch between two calls | Double tap the power button |
| Activate voice assistant | Double tap the power button |
Q&A
– 1. Connect with a Type-C charging adapter to charge .(Charging current is not greater than 1A).
– 2. When not using for a long time, please charge it once every three months at least.
– Method 1. Long press the volume button “+” and “-” at the same time for 3 seconds (long press the volume button “+” and “-” in the music and call state is invalid).
– Method 2. Turn off the Bluetooth of mobile phone , the headset will disconnect.
– Step 1. Turn on the headset, and connect device A to the headset.
– Step 2. Disconnect device A , and the headset enters pairing mode.
Step 3. Connect device B to the headset.
– Step 4. Manually connect device A to the headset again.
– After manually connecting two devices for the first time, they will connect automatically the second time.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC ID
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference thatmay cause undesired operation of the device.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
