01_21-682 Solar Wild Boar

Product Information: Solar Wild Boar

Solar Wild Boar is a basic solar DIY toy that is ideal for a
do-it-yourself science fair, after-school, or summer workshop
project. It provides the bonus gift of learning mechanical
transmission and electrical motor theory. With only 47 assembly
parts, it is a wonderful instrument for beginners aged 8 years and
up, and serves as a gateway to ignite opportunities in fun
learning.

Tools You May Need:

• Diagonal Cutter
• Hammer

Mechanical Parts List:

Note: The product contains functional edges and
sharp points. Please exercise caution during assembly and
usage.

Product Usage Instructions:

It’s time to have some FUN! Follow the steps below to use the
Solar Wild Boar:

1. Take the Solar Wild Boar outside under direct sunlight for best
   results. It operates most effectively on a sunny day.
2. If you want to have indoor fun, use a 50 watt halogen light.
   The product will not run on a cloudy day, shaded locations,
   indirect sunlight, or under a fluorescent light.

Please Note: Do not connect the wires to the
mains.

This information is taken from the user manual of the Solar
Wild Boar product.

GREEN ENERGY
M a n u a l Assembly & Instruction

SOLAR WILD BOAR
Solar Wild Boar is a basic solar DIY toy, it is ideal for a do-it-yourself science fair, after-school, or summer workshop project with the bonus gift of learning mechanical transmission and electrical motor theory. With only 47 assembly parts, it’s a wonderful instrument for the beginner enthusiast 8 years and up, and a gateway to ignite opportunities in fun learning.
Tools You May Need

Diagonal Cutter

Hammer

Mechanical Parts List

Product contains functional edges and sharp points.

P1

Solar Panel With Motor

P2

Pinion Gear (Yellow)

P3 Gear(Red)

QTY

QTY

QTY

1

1

Don’t connect the wires to the mains.

P4 Gear(Orange)

P5 Gear With Shaft(Blue) P6

QTY

QTY

1

1

1
Sponge QTY 1

P7

Hex Shaft

P8 Round Shaft(Short) P9 Round Shaft(Long)

QTY

QTY

QTY

2

1

2

1

66

5

2 7
3 4
4

Plastic Parts
Cut the plastic parts when they are required. Do not cut them in advance.

88

2

1

4

1

B

C3

35

11

8

6

9

10

7

A

3

2

1

Hints

Cut off the burrs before assembly. burr
burr

2

Mechanical Assembly

1

2

P1

P2
C4
Correct Incorrect

P6
2
1

3

4

P3(Red)

A1 P8(Short)

2 1

Side View
Correct

Incorrect

3

5

Correct

Incorrect

P5
2
1
P4

P3

P5

P4

Cut off B4 burrs before assembly.

A11

B4

6 Ensure parts facing the right direction (see below).
Correct

B4
2 1
B1

Incorrect

Incorrect Incorrect

B7
4

7 Use your finger to hold the parts ( as shown below ), it may help you assemble the parts smoothly.
1
Side View

2

A10

8

Cut off the

two burrs before

A2

assembly.

2
A2

1

Incorrect

Use your finger to hold the parts ( as shown above ), it may help you assemble the parts smoothly.

9

Incorrect 5

10
C2

11
A4

12 B8x3

13

A5
Slightly hammer P7 into A5.

P7

2

The open -side – face up ( as per the pic).
6

14 < Note > Step 14~19 Have the parts assemble on the desk/or platfrom, it may help to
install smoothly.
B3
P9x2 (Long)

15
C3x2

Very Important ! Press C3 to the bottom.
Incorrect
Correct
7

16

17

B2

Very Important !
Please point the feet in the direction illustrated above before inserting B2 part.

18
A3
B5

19
C1

8

20 A6

B6x3

21

Very Important !

Please point the feet in the direction illustrated before inserting into the shaft.

2

22

23 Running

Incorrect

Cut off A7 & A8 burrs before assembly.
A8 A7
R
L
A9
9

It’s time to have some FUN !
1. Take outside under direct sunlight. Best results are obtained when operated on a sunny day. 2. For indoor fun, use a 50 watt halogen light. The product will not run on a cloudy day, shaded
locations, indirect sunlight, or under a Fluorescent light.
10

Copyright © 2017 CIC. All rights reserved

4350006821