How can we help you with your Shark HydroVac today?
The three water droplets light will flash blue when you need to refill the Clean Solution Tank.
The Area Rug and Three Water Droplets lights will flash red alternatingly when the brushroll is blocked. Remove the nozzle cover, brushroll, and Dirty Water Tank. Check the air path for any blockages. If these two symbols are blinking at the same time then that means the brush roll garage door is removed. Ensure that the bottom latches of the garage door are properly inserted in the slots.
The Shark HydroVac™ Cordless Pro vacuums, mops and cleans itself with powerful suction & hydro mopping at the same time. It deep cleans hard floors and cleans area rugs. Includes a continuously self-cleaning, antimicrobial brushroll; 2-tank system to separate clean & dirty water; LED display and multi-surface concentrate with odor neutralizer technology. The VacMop is meant for hard floors only, and requires individual usage of the vacuum and mop feature.
Yes, the Hydrovac is designed to clean your area rugs, as well as your hard floors.
No, it does not. The brushroll is designed to clean your hard floors and area rugs without damaging them. It is recommended to test the unit on a sensitive area during first time use.
The Hydrovac can be used on hard floors such as sealed woods, tile, vinyl, as well as low pile area rugs.
The Hydrovac can not be used for dry vacuuming. There must be fluid in the Clean Solution Tank for the unit to run. The unit will turn off and indicate when you have run out of cleaning solution.
It is not recommended that you use third party cleaning solutions with the Hydrovac. The Hydrovac Multi Surface Cleaning Solution is specifically designed for this system to optimize cleaning performance. Third party cleaning solutions will lead to foaming, streaking and false triggering of the dirty water sensors
The Hydrovac weighs approximately 8 lbs.
The dimensions of the Hydrovac are11.06 in L x 9.81 in W x 43.73 in H
The Hydrovac runs at a wattage of 5.5
The Clean Solution Tank capacity is 0.36L or 0.5L depending on the version of the Hydrovac you buy.
The Dirty Water Tank capacity is 0.36L.
The temperature can be between 40 degrees F and 95 degrees F. Normal tap water is good to use for cleaning. Please do not use boiling water as this may damage internal parts.
You can adjust the flow by changing between Everyday mode and Area Rug mode. Each mode is optimized for the corresponding surface type.
Yes, the Hydrovac can pick up animal hair and move it to the Dirty Water Tank.
Normally, this will not happen due to the brushroll diameter and the general length of pet hair. If there is a tangle around the brushroll, take out the brushroll and remove the hair wrapped around it. Be careful not to damage the brushroll if you use any sharp tools.
We do not recommend using bleach as it may damage the unit.
The warranty is 3 years long.
Generally self-clean cycle will take care of all internal cleaning of the unit. It is a good practice to check for debris stuck behind the brushroll. To do this please open the brushroll cover and remove the brushroll from it’s slot. If there is debris present, please clean with a paper towel. Be careful to not use any rough cleaning tool that could damage parts during cleaning.
1. Dirty Water Tank should be empty.
2. Clean Solution Tank should be at least ½ full.
3. i. battery level should be at least (1 solid bar on battery icon)
ii. charging dock should be connected to a power outlet, and the HydroVac™ should be docked properly (make sure the HydroVac™ is seated on the 2 metal contacts on the dock post).
4. Once you’re ready, press and release the Power button to initiate the Self-Clean Cycle.
If it doesn’t proceed to the cycle, and the
i. blue water droplets flash, it is indicating you don’t have enough water in the Clean Solution Tank. Fill the Clean Solution Tank, andretry running the Self-Clean Cycle.
ii. red water droplets flash, it is indicating the dirty water tank is full. Remove and empty the Dirty Water Tank. Remount the Dirty Water Tank, and retry running the Self-Clean Cycle.
5. Once Cleaning Cycle is complete (should take about 2 full minutes), remove and empty the Dirty Water Tank. It’s recommended to also rinse the [dirty water tank, solid parts trap, and the foam filter] and dry before reinstalling onto the HydroVac™.
While the charging dock is plugged in, place the unit onto the dock. The battery icon will illuminate, indicating that it is charging.
On a full charge, the Hydrovac will run for 20 minutes.
The Hydrovac takes about 4 hours to fully charge.
Yes, you can leave the unit on the charging dock even after it has fully charged. The charging will turn off once the battery is completely charged.
6 months
6 months
