Jl Audio Xdm200-2 200w 2-channel Amplifier Owner's Manual

XDM200-2 200W 2-Channel Amplifier

Product Information:

The M20/200W 2-CHANNEL AMPLIFIER is a high-quality audio
amplifier designed for automotive or marine installations. It
features advanced S.WITHNG technology for efficient power delivery
and comes with various controls and connections for versatile
usage.

Product Usage Instructions:

Before using the amplifier, please consider the following
installation and safety considerations:

Installation Considerations:

• Ensure proper power connection by connecting the positive
  (+12V) power wire and negative (GND) ground wire.
• Connect the positive (+12V) activation wire to control the
  amplifier’s power.
• Make appropriate connections for input signals using the
  provided RCA cables.
• If desired, connect a remote level controller (HD-RLC or
  MHD-RLC) for easy adjustment of the amplifier’s volume.
• Connect the speaker outputs according to your setup, either
  using CH. 1 (L) and CH. 2 (R) outputs or bridging them
  together.

Safety Considerations:

• Ensure the amplifier is powered off during installation.
• Avoid short circuits by properly connecting the power and
  ground wires.
• Do not exceed the recommended power specifications of the
  amplifier.

Controls:

The amplifier features several controls for configuring its
operation:

• Status LED: Indicates the operating status of the
  amplifier.
• Turn On Mode: Configures the activation method of the
  amplifier.
• Input Filter: Configures the input filter application for
  optimal performance.
• Input Sensitivity: Adjusts the input stage sensitivity of each
  channel pair.
• Filter Mode: Configures the filter mode of CH. 1&2 for
  frequency attenuation.
• Filter Frequency: Adjusts the cutoff frequency of the active
  filter.

Appendix A: Input Sensitivity Level Setting

To achieve overall system balance, follow the steps below to
adjust the input sensitivity of each amplifier channel pair:

Necessary Equipment:

• Speaker(s)
• Source unit
• Processors (if used)

The Nine-Step Procedure:

1. Disconnect the speaker(s) from the amplifier’s speaker output
   connectors.
2. Turn off all processing (bass/treble, loudness, EQ, etc.) on
   the source unit, processors (if used), and amplifier.
3. Set the fader control to the center position and the subwoofer
   level control to 3/4 of maximum, if used.

)< M20/
200W 2-CHANNEL AMPLIFIER
OWNER’S MANUAL MANUEL D’ UTILISATION MANUAL DEL PROPIETARIO BEDIENUNGSANLEITUNG MANUALE DEL PROPRIETARIO
N e x o··
S.WIT(H NG TECHNOLOGY

xl

2.5mm xl

xl

– – – – – – – – – – – — – -=====~ 2 I JLAudio·-XCXDWM~20~0/-;;2

INSTALLATION CONSIDERATIONS
· Installation requires appropriate tools and safety equipm ent. Professional installation is recommended.
· This product is water-resistant. Do not submerge or subject to high-pressure water spray.
· Before installation, turn off the audio system and disconnect the battery system from the audio system.
· When possible, install in a dry, well-ventilated location that does not interfere with factoryinstalled systems. If a dry environment is not available, a location that is not exposed to heavy splashing may be used.
· Do not install in the engine compartment, any areas of extreme heat or where it will be directly exposed lo the elements.
· Before cutting or drilling, check for potential obstacles behind mounting surfaces.
· Carefully route all system wiring away moving parts and sharp edges; secure with cable ties or wire clamps and use grommets and loom where appropriate to protect from sharp edges.

SAFETY CONSIDERATIONS
· Only use this product with 12 volt, negativeground electrical systems. This product is not certified or approved for use in aircraft.
· Mount this product securely to prevent damage or injury in severe conditions.
· An appropriate fuse (or circuit breaker) at the main power wire is vital for vehicle/vessel safety and must be installed within 18 inches (45 cm) of the positive battery connection.
· For ABYC and NMEA applications, circuit protection is required within 7 inches (18 cm) of the battery, unless the cable is in an enclosure or conduit.
· Listen to your audio system at levels appropriate for operating conditions and hearing safety.

I

3

CONNECTIONS

.,.__….,.__.,voe ._ –
XDM200/2

I I Connection

Description

+12VDC

Positive(+12V) Power Connection

0

Ground

Negative (GND) Ground Connection

Remote

Positive (+12V) Activation Connection

I

Notes

· 4 AWG wire (8 AWG minimum) · Install 20A fuse at(+) battery post

· 4 AWG wire (required)

· 18 – 12 AWG wire capacity
O · See Turn On Mode for more info

f)

CH. 1 Input CH . 2 Input
Preout 1 Preout 2

Left Input Signal, Black RCA Right Input Signal, Red RCA Left Pass-Through Preamp Signal, Black RCA Right Pass-Through Preamp Signal, Red RCA

· Accepts 200mV – 4V input voltage
O · See Input Mode for more info
· Same signal that is connected to CH. 1&2 inputs
· Unaffected by the amplifier’s filters

e

Remote Level Control

Remote Level Controller Connection (optional) (HD-RLC or MHD-RLC)

· Operates as an attenuator only: Fully counter-clockwise= Level Muted Fully clockwise= Level Unaffected Multiple amplifiers can be controlled from a single HD-RLC using a nonduplex phone line splitter and multiple phone cables.

e

CH. 1 (L) Speaker Output
CH.2 (R) Speaker Output

(±) (+) Positive Speaker Output
= (-) Negative Speaker Output

I CH. 1&2 Bridged (+)

(±) (+) Positive Speaker Output
= I (-) Negative Speaker Output CH. 1&2 Bridged (-)

· Minimum impedance load: Stereo mode 2:2 ohms Bridged mode 2:4 ohms
· 16 – 8 AWG wire capacity

4 I JL Audio· – XDM200/2

CONTROLS

JLAUDIO.
XOM200/2
2 (KANN(lAMl’l.lU
©
– – (~ @ (@] ·UWOC
m

e8 I
·–_,I_Cr_!,]… mar =0
— ~-~- l~l,d-l

·E)u 0
8· ·0

,….. , . . . (H,j
©
(©©©©)
®C:.,’ 0 @c;.,io

@~

I Control (Function) I Setting I

Description

Flashing Green

Amplifier Powering Up, Audio Output Muted

Green On-Normal Operation, Active Audio Output

e

Status LED (indicates operating status)

Red
Amber (yellow)

On-Safe Mode, Over-Temperature Condition, Audio Output Reduced · Reverts to normal operation when temperature returns to a safe level
On-Safe Mode, Over-Current Condition, Audio Output Muted May exhibit repetitive, audible ticking or thumping noise in the output
· Inspect for speaker/wire short circuit or low impedance

LEDs Off Remote

Amplifier Turns Off (unexpectedly), Low-Voltage Condition Occurs when battery or remote turn-on voltage drops below 10V
· Reverts to normal operation when voltage rises above 1lV
+ 12V Remote Turn-On (Preferred} Controlled by a switched+12V circuit or turn-on output of your source unit/OEM interface

e

Turn On Mode (configures activation method}

Offset Signal

DC Offset-Sensing (Automatic} · Turns On by detecting the presence of small DC
signal in OEM audio outputs and turns Off after the signal is removed
Signal-Sensing (Automatic} · Turns On by detecting full-range OEM audio
signals and turns OFF after the signal is removed (within 30 seconds}

Designed for high-level (speaker} signals only Detects input signal from CH. 1 (L} only Using DC Offset or Signal Sensing methods will turn the “Remote” terminal into a + 12V turn-on output.

Input Filter (configures input filter application}
Input Sens. (adjusts each channel pair’s input stage}
Filter Mode (configures the filter of CH. 1&2}

Car Boat

Select for most installations (automotive or marine} Select if experiencing interference from high-current mechanical switches/devices

Variable

Use to match the source unit’s output voltage with the inputs of each pair of amplifier channels. See Appendix A for detailed information.

Off

Filter defeated; passes full range of frequencies present at the inputs

HP

Attentuates frequencies below the CH. 1&2 “Filter Freq. (Hz}” dial, at a rate of 12d8/octave

Filter Freq. (Hz} (adjusts filter cutoff frequency}

LP Variable

Attentuates frequencies above the CH. 1&2 “Filter Freq. (Hz)” dial, at a rate of 12d8/octave
Use to adjust the cutoff frequency of channel 1&2’s active filter, from SO Hz – 500 Hz/ 12d8 per octave

I

5

APPENDIX A: Input Sensitivity Level Setting Follow the steps below to adjust the input sensitivity of each amplifier channel pair to achieve overall system balance.
Necessary Equipment
· Digital AC Voltmeter · Sine-wave test tone recorded at OdBfs reference level in the frequency range to be amplified.
Do not use attenuated test tones (-10 dB, -20 dB, etc.). Full range channel/amplifier applications: 1 kHz Subwoofer channel/amplifier applications: 50 Hz · Depending on your type of source unit, the sine-wave may be played via a CD, USB thumb drive, portable media player or Bluetooth· audio source. Make sure to disable any EO/DSP modes on your portable media player during level setting.
The Nine-Step Procedure
1. Disconnect the speaker(s) from the amplifier’s speaker output connectors.
2. Turn off all processing (bass/treble, loudness, EQ, etc.) on the source unit, processors (if used) and amplifier. Set the fader control to center position and the subwoofer level control to 3/4 of maximum, if used.
3. Turn all “Input Sens:’ controls all the way down.
4. Set the source unit volume to 3/4 of full volume. This will allow for reasonable gain overlap with moderate clipping at full volume.
5. Using the chart below, determine the target voltage for input sensitivity adjustment according to the nominal impedance of the speaker system connected to the amplifier outputs.
6. Verify that you have disconnected the speakers before proceeding. Play a track with an appropriate sine wave (within the frequency range to be amplified) at 3/4 source unit volume.
7. Connect the AC voltmeter to the speaker output terminals of the amplifier. If the channel pair is operating in stereo, it is only necessary to measure one channel. If bridged, make sure you test the voltage at the correct terminals (L+ and R-).
8. Increase the”lnput Sens.” control until the target voltage is observed with the voltmeter.
9. Once you have adjusted each channel section to its maximum low-distortion output level, reconnect the speaker(s). The “Input Sens.”controls can now be adjusted downward if the amplifier requires attenuation to achieve the desired system balance.
IMPORTANT!
· Do not increase any “Input Sens:’ setting for any amplifier channel or channel pair in the system beyond the maximum level established during this procedure. Doing so will result in audible distortion and possible speaker damage.
· It will be necessary to re-adjust the”lnput Sens:’ if any equalizer boost is activated after setting the”lnput Sens:’ with this procedure. This applies to any EQ boost circuit, including source unit tone controls or EQ circuits. EQ cuts will not require re-adjustment.

~ Nominal
Impedance
sn
40 20

17.3 V 17.3 V 14.1 V

34.6V 28.2V not recommended

6 I JL Audio· – XDM200/2

SPECIFICATIONS

Amplifier Section

Amplifier Topology NexDTMUltra-High Speed Class D

Power Supply Type Unregulated MOSFET Switching

Minimum Copper 8AWG Power/ GND Wire (Note: (CA/ Copper Clad Aluminum wire is not recommended.)

Recommended Fuse 20A

Rated RMS Power @ 14.4V, < 1% THD+N

7SWx2 @40 1SOW x 1 @ 8 0 Bridged

lOOW x 2 @2 0 200W x 1 @4 0 Bridged

Rated RMS Power @ 12.SV, < 1% THD+N

60Wx2 @40 120W x 1 @8 0 Bridged

Frequency Response 12 Hz – 22 kHz (+0, -1dB)

S/ N Ratio (A-weighted, 20 Hz- 20 kHz
noise bandwidth)

> 104 dB (Referred to rated power), >84 dB (Referred to 1W)

90Wx 2@ 20 180W x 1 @4 0 Bridged

Damping Factor > 150 / SO Hz @4 0 , > 7S / SO Hz @ 2 0

Input Section Number of Inputs 2 (One Stereo Pair) lnputType Differential-Balanced with RCA jack inputs
Input Voltage Range 200mV – 4V RMS Signal Processing
Active, 12dB/ octave, High-Pass or Low-Pass Filter Type (SO – 5,000 Hz), defeatable Remote Level Control HD-RLC or MHD-RLC (optional). Full mute to O dB range.

I

Due to o ngoing product development, all specifications are subject to change w ithout notice. 7

Printed in China

XDM200/2 MAN-05272022

USA Limited Warranty
FOR CAR AUDIO PRODUCTS SOLD AT RETAIL:
JL Audio warrants these products to be free of defects in materials and workmanship from the original date ofpurchasefor these periods:
One (1) year from the original date ofpurchase:CarSpeakers and Subwoofers
Two (2) years from the original date of purchase: Car Amplifiers, Electronlcs, Enclosed Subwoofers, Stealthbox and Connection Products
Note: The Car Amplifier Warranty Period Is extended to three (3) years when accompanied with the purchase of a qualifying JL Audio Amplifier Power Connection System and with installation by an authorized JL Audio dealer.
This warranty is not transferable and applies only to the original retail purchaser from an authorized JL Audio dealer in the USA. Should service be necessary under thiswarranty for any reason due to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge.
Note: Products purchased from unauthorized dealers are not covered under warranty.
Damage caused by the following is not covered under warranty: accident, misuse, physical abuse, product modification or neglect, failure to follow Installation instructions, unauthorized repair attempts, misrepresentations by the seller. loudspeakers with thermal or over-excursion damage are not covered under warranty. This warranty does not cover incidental, accidental or consequential damages and does not cover the cost of removing or reinstalling products. Cosmetic damage due to improper handling, accident or normal wear and tear or exposure to harsh chemicals is not covered under warranty. Jl Audio will not be responsible for restoring or maintaining custom finishes or cosmetic treatments applied toproducts.
This warranty is void If the product’s serial number has been removed, altered or defaced.
Any applicable implied warranties are limited in duration tothe period ofthe express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you.This warranty gives you specific legal rights, and you mayalso have other rights which vary from state to state.
If you need service on your JL Audio product:
All USA retail warranty returns should be nnt to JLAudio freight prepaid through an authorized JL Audio dealer and must be accompanied by proofofpurchase (a copyof the original retail sales receipt.) Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized by Jl Audio with avalid return authorization number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated asthisdate is prior to purchasedate.Return only defective components. (If one speaker fails in asystem, return only that speakercomponent, not the entire system.)Non-defective itemsreceived will be returned freight-collect. Customer is responsible for shipping charges and insurance in sending the product to Jl Audio. Freight damage on returns is not covered under warranty.

JL Audio Customer Service: 1-954-443 -1100 9:00 AM – 5:00 PM (Eastern Time Zone)
JL Audio Technical Support: www.jlaudio.com/support
Original Equipment Warranty
For JL Audio products installed as original equipment by a boat or vehicle manufacturer, warranty coverage Is provided within the boat or vehicle manufacturer’swarranty program.Please contact your boat dealeror manufacturer.
International Warranty
JL Audio Car Audio products are warrantied against defects in materials and workmanship for a minimum time period as stated in the USA warranty above, beginning on thedate of purchasefrom aDealerauthorized by aJL Audio Distributor. The warranty is only valid within the country of purchase and products are covered by each country’s JL Audio Distributor warranty program. To find your country’s Distributor please visit this link:www.jtaudio.com/pages/dealer-locator
Consumers In the EEA countries and the Russian Federation are protected by local consumer law and benefit from local statutory warranties. Jl Audio reserves the right to change or modify any of the terms and conditions
contained in this Warranty Statement, at any time and in our sole discretion.
Any changes or modification will be effective immediately upon posting of the
revisions on the JL Audio website at www.jlaudlo.com/warranty,and you waive any right you may have to receive specific notice of such changes or modifications.