PLED-DNBF5 6 Inch 12W LED Recessed Downlight
Product Information:
The 6 Inch 12W LED Recessed Downlight – 5CCT|Baffle Trim
(PLED-DNBF5/612W5CCTDIM) is a versatile lighting fixture designed
for residential and commercial use. It features a color temperature
selector switch that allows you to choose between five different
color temperatures: 2700K Warm White, 3000K Soft White, 4000K Cool
White, 5000K Day Light, and 6000K Bright White. The downlight is
compatible with various dimmer models, providing flexibility in
adjusting the brightness level.
For more information and details about the product, you can
visit our website www.parmida.com or contact our
customer support team at [email protected].
Product Usage Instructions:
- Before starting the installation process, ensure that the power
is turned off at the source. - Remove any existing trim from the installation area before
proceeding. - If you are using a traditional can, screw the E26 base adapter
included in the installation kit into the can. - If you are using a 6-inch housing can, rotate the three
aluminum tabs on the back of the light to their most extended
position. If using a 5-inch housing can, do not rotate the aluminum
tabs. - Connect the male connector of the E26 base adapter with the
female connector of the light. - Arrange the wires and push the light inside the housing can for
a secured installation. Please note that once the light is pushed
inside the can, avoid rotating it as it may change the position of
the aluminum tabs and compromise the installation.
If you are using a Title 24 Can, follow these additional
steps:
- Remove the E26 base adapter from the light by detaching the
male and female connectors. - Insert the male connector from the Title 24 Can into the female
connector of the light. - If you are using a 6-inch housing can, rotate the three
aluminum tabs on the back of the light to their most extended
position. If using a 5-inch housing can, do not rotate the aluminum
tabs. - Arrange the wires and push the light inside the housing can for
a secured installation. Again, avoid rotating the light once it is
pushed inside the can to maintain the position of the aluminum
tabs.
Please remember to consult the Dimming Control Manufacturer’s
instructions for proper installation of all dimming controls. For a
list of compatible dimmers and more details, refer to our website
or contact our customer support team.
INSTALLATION GUIDE
6 INCH 12W LED RECESSED DOWNLIGHT – 5CCT|BAFFLE TRIM
PLED-DNBF5/612W5CCTDIM
IMPORTANT: Please read carefully and save these instructions, as you may need them at a later date. When using electrical equipment, basic safety precautions should always be followed as below: READ AND FOLLOW BELOW SAFETY INSTRUCTIONS GENERAL: All electrical connections and wiring must be performed by a qualified electrician and must be in accordance with local and National Electrical Code (N.E.C). LED Retrofit Kit installation requires knowledge of luminaire electrical systems. Install this kit only in luminaire that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. 1. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. 2. To prevent wiring damage or abrasion do not expose wiring to edges of sheet metal or other sharp objects. 3. Suitable for wet locations. 4. Supply conductors (power wires) connecting the light must be rated minimum 194°F (90°C). If uncertain consult an electrician. 5. Suitable for Type IC or suitable for Type non-IC. 6. This device is not intended for use with emergency exits. 7. This light is dimmable. Dimming range is 10%-100%. Please refer to our website for the most up-to-date compatible dimmer list. NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. UNPACKING: Thoroughly inspect the light for freight damage. Freight damage should be reported to the delivery carrier.
SELECTING COLOR TEMPERATURE
To avoid risk of damage, ensure wall switch connected to the light is turned to off position before changing or selecting desired color temperature (CCT) on the selector switch. Select the color temperature via the CCT switch located on the side of the light. Using the color (CCT) selector switch, select the desired color temperature (2700K Warm White, 3000K Soft White, 4000K Cool White, 5000K Day Light, or 6000K Bright White).
COMPATIBLE DIMMER LIST
DIMMING
Dimming performance may depend on the dimmer, the dimmer range adjustment setting (for dimmers with brightness range adjustments), the wiring method, and/or the number of LED modules installed onto the dimmer circuit.
For best results, it is recommended to install a minimum of four LED modules onto one dimmer.
Before turning on the LED lights, set dimmer position at maximum before adjusting to a lower light level.
Please follow the Dimming Control Manufacturer’s instructions for the installation of all dimming controls.
NOTE: The table shows dimmers that have been tested and have demonstrated proper operation under normal conditions.
The absence of a dimmer from this chart does not necessarily imply incompatibility.
Please visit our website www.parmida.com or contact our customer support team for more details.
LUTRON PD6WCL MSCL-OP153M CN-600P DVCL-153P2.1 SCL-600P SLV-600P MACL-153M DV-600P
LEVITON IPL06 DSL06 IPI06 6674 6631
www.parmida.com
STEPS FOR INSTALLATION TRADITIONAL RECESSED CAN
1. Ensure power is turned off at the source before installing the light.
2. Remove any existing trim prior to installation of this light.
3. Screw the E26 base adapter included in the installation kit into the traditional can.
4. For 6″ housing can rotate the 3 aluminum tabs on the back of the light to their most extended position. If using a 5″ housing can, do not rotate the aluminum tabs.
5. Connect the male connector of the E26 base adapter with the female connector of the light.
6. Arrange the wires and push the light inside the housing can for secured installation.
Note: Be careful not to rotate the light once it’s pushed inside the can, because it may change the position of the aluminum tabs which in turn will not ensure a secured installation.
STEP 1 & 2 COMPATIBLE HOUSING CAN
STEP 4 ALUMINUM TABS
STEP 3 E26 ADAPTER 5-6″
STEP 5
STEP 7
STEPS FOR INSTALLATION TITLE 24 CAN
1. Ensure power is turned off at the source before installing the light.
2. Remove any existing trim prior to installation of this light.
3. When using a Title 24 Can, remove the E26 base adapter from the light by detaching the male and female connectors.
4. Insert the male connector from the Title 24 Can into the female connector of the light.
5. For 6″ housing can rotate the 3 aluminum tabs on the back of the light to their most extended position. If using a 5″ housing can, do not rotate the aluminum tabs.
6. Arrange the wires and push the light inside the housing can for secured installation.
Note: Be careful not to rotate the light once it’s pushed inside the can, because it may change the position of the aluminum tabs which in turn will not ensure a secured installation.
STEP 1 & 2 TITLE 24 CAN
SUPPLY WIRE
STEP 4
WARNING
RISK OF FIRE OR ELECTRIC SHOCK.
DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE LIGHT.
DO NOT PLACE YOUR HAND UNDERNEATH SPRING CLIPS DURING REMOVAL PROCESS. SNAPPING OF THE CLIPS CAN CAUSE INJURIES TO THE HAND.
DO NOT USE ANY OTHER DRIVER EXCEPT PARMIDA LIGHTING DRIVER THAT IS INCLUDED WITH THE LIGHT.
STEP 3 MALE CONNECTOR FEMALE CONNECTOR
STEP 5 ALUMINUM TABS
STEP 6
www.parmida.com
Parmida LED - Energy Efficient LED Lighting Solutions — Parmida LED Technologies
