AGT-BDRC48 Skid Steer Front Mount Cutter Adjustable
AGT Industrial Product Manual
Skid Steer Front Mount Cutter-Adjustable Model: AGT-BDRC48
Ver.1.1.3
https://www.agrotkindustrial.com/
Table of Contents
- TO THE OWNERS
- SAFETY PRECAUTIONS
- OPERATION INSTRUCTIONS
- STORAGE INSTRUCTIONS
- NOTES
To the Owners
General Comments
Congratulations for having this Front Mount Cutter! Your Front
Mount Cutter was carefully designed and manufactured to give you
years of dependable service. Your Front Mount Cutter will require
some minor maintenance to keep it in top working condition. Please
observe all safety precautions and maintenance procedures as
described in this manual.
Before Operation
Thoroughly read and understand the instructions given in this
manual before operation. Refer to the Safety Label section, read
all instructions noted on them.
Do not allow anyone to operate his equipment who has not fully
read and comprehended this manual and who has not been properly
trained in the safe operation of the equipment.
Service
Please remember to use only manufacturer replacement parts.
Substitute parts may not meet the standards required for safe,
dependable operation.
Safety Precautions
Before Operation
IMPORTANT:
- Operator should be familiar with all functions of the
unit. - Make sure all guards and shields are in place and secured
before operating implement. - Keep all persons away from equipment and work area.
- Dismounting from a moving unit can cause serious injury or
death. - Keep hands, feet, and clothing away from power-driven
parts. - Detach and store implement in an area where children normally
do not play. Secure implement by using blocks and supports.
Always wear proper safety glasses, goggles, or a face shield
when driving pins in or out, or when any operation causes dust,
flying debris, or any other hazardous material.
Operator Safety
Wear protective clothing and equipment appropriate for the job.
Clothing should be snug fitting without fringes and pull strings to
avoid entanglement with moving parts. Prolonged exposure to loud
noise can cause hearing impairment or hearing loss. Wear suitable
hearing protection such as earmuffs or earplugs. Operating
equipment safely requires the operators all attention, Avoid
wearing radio headphones while operating machinery.
Tool Safety
Inspect entire machine before each use. Replace damaged or worn
parts. Check for fuel leaks and make sure all fasteners are in
place and securely fastened.
Wear Protective Equipment
Transportation and Storing
Store machine and fuel where fuel vapors cannot reach sour
combustion like, water heaters, electric motors, switches,
furnaces, etc. Always secure the machine with tie downs or similar
restraints when transporting. The machine be stored in a manner
that prevents it from falling, rolling or tipping.
Operation Instructions
The Skid Steer Front Mount Cutter-Adjustable Model: AGT-BDRC48
is designed to be mounted on a skid steer and used for cutting
various types of vegetation. Before operation, please ensure that
all safety precautions have been taken and the machine is in good
working condition.
- Mount the cutter onto the skid steer according to the
instructions provided. - Start the skid steer engine and engage the cutter.
- Adjust the cutting height according to your needs.
- Slowly drive the skid steer forward, cutting the vegetation in
front of you. - When finished, disengage the cutter and turn off the skid steer
engine.
Storage Instructions
After use, the Skid Steer Front Mount Cutter-Adjustable Model:
AGT-BDRC48 should be stored in a dry, secure location away from
children. Follow these steps:
- Detach the cutter from the skid steer and clean any debris from
the blades. - Inspect the machine for any damage or wear and replace any
parts as necessary. - Store the machine in a manner that prevents it from falling,
rolling or tipping. - Secure the machine with tie downs or similar restraints when
transporting.
Notes
If you have any questions or concerns about your Skid Steer
Front Mount Cutter-Adjustable Model: AGT-BDRC48, please contact AGT
Industrial at [email protected] or visit our website at
https://www.agrotkindustrial.com/.
AGT INDUSTRIAL
PRODUCT MANUAL
Skid Steer Front Mount Cutter-Adjustable Model:AGT-BDRC48
Ver.1.1.3
https://www.agrotkindustrial.com/
TABLE OF CONTENTS
TABLE OF CONTENTS
2/17
TO THE OWNERS
3/17
SAFETY PRECAUTIONS
4/17
OPERATION INSTRUCTIONS
7/10
STORAGE INSTRUCTIONS
9/10
NOTES
10/10
P2
https://www.agrotkindustrial.com/
TO THE OWNERS
GENERAL COMMENTS
Congratulations for having this Front Mount Cutter! Your Front Mount Cutter was carefully designed and manufactured to give you years of dependable service. Your Front Mount Cutter will require some minor maintenance to keep it in top working condition. Please observe all safety precautions and maintenance procedures as described in this manual.
BEFORE OPERATION
Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.
Do not allow anyone to operate his equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.
SERVICE
Please remember to use only manufacturer replacement parts. Substitute parts may not meet the standards required for safe, dependable operation.
P3
https://www.agrotkindustrial.com/
SAFETY PRECAUTIONS
BEFORE OPERATION
1. The operator must read the operation manual carefully before installation, operation or maintenance. Improper operation will cause the machine damage or the operator death. 2. Read all the safe signs and safe declarations. Follow all the professional safe terms, local laws or the professional directions. 3. Familiar with the Front Mount Cutter about functions, specs and operation. Replace the to-be-damaged parts in time. Make sure all the hydraulic installations and couplings connect firmly, and all the safe signs stick on the suitable positions clearly.
IMPORTANT
1. Operator should be familiar with all functions of the unit. 2. Make sure all guards and shields are in place and secured before operating implement. 3. Keep all persons away from equipment and work area. 4. Dismounting from a moving unit can cause serious injury or death. 5. Keep hands, feet, and clothing away from power-driven parts. 6. Detach and store implement in an area where children normally do not play. Secure implement by using blocks and supports.
Always wear proper safety glasses, goggles, or a face shield when driving pins in or out, or when any operation causes dust, flying debris, or any other hazardous material.
P4
https://www.agrotkindustrial.com/
SAFETY PRECAUTIONS
Operator Safety
Wear protective clothing and equipment appropriate for the job. Clothing should be snug fitting without fringes and pull strings to avoid entanglement with moving parts. Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hearing protection such as earmuffs or earplugs. Operating equipment safely requires the operators all attention, Avoid wearing radio headphones while operating machinery.
Tool Safety
Inspect entire machine before each use. Replace damaged or worn parts. Check for fuel leaks and make sure all fasteners are in place and securely fastened.
P5
https://www.agrotkindustrial.com/
SAFETY PRECAUTIONS
Wear Protective Equipment
Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic lines or performing work on the system. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system. Use a piece of paper or cardboard, NOT BODY PARTS to check for suspected leaks. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. DO NOT DELAY. If an accident occurs, see a doctor familiar with this type of injury immediately. Any fluid injected into the skin or eyes must be treated within a few hours or gangrene may result.
Transportation and Storing
Store machine and fuel where fuel vapors cannot reach sour combustion like, water heaters, electric motors, switches, furnaces, etc. Always secure the machine with tie downs or similar restraints when transporting. The machine be stored in a manner that prevents it from falling, rolling or tipping.
P6
https://www.agrotkindustrial.com/
OPERATION INSTRUCTIONS
S/N
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART DESCRIPTION Part 1 Part 2 Part 3
Bolt M12*80 Bolt M16*140 Locking nut M12 Turing Pivot Lock Nut M16 Bolt M16*120
Pin Cover Lock Washer Bolt M8*25 Front pin Flip cylinder Oscillating cylinder
QTYS 1 2 3 2 1 2 1 2 1 1 1 1 1 1 1 1
NOTE
P789
https://www.agrotkindustrial.com/
OPERATION INSTRUCTIONS
Assembly instructions
All the bolts, spring washers, float washers, nuts, and pins required for assembly are installed in the parts to be assembled. 1.Unscrew 4,6,7 on P2, Join P1 and P2 by following the sequence of 7,4,6, make sure Joint at P1 and P2 can be free rotated steady. 2.unscrew 4610 on P2, connect Part2 and Part3 by following the sequence 10,4,6, make sure Joint at P2 and P3 can be free rotated steady. 3.Unscrew 11,12,13,14 on P2, screw P2 and P3 at point 16 by following the sequence 14,11,12,13. 4.Unscrew 5,8 on Part 1, 8 and 9 on part2, the hydraulic cylinder (15) in place showed as picture, screw 5 & 8 on part1 and 8 & 9 on part 2.
P8
https://www.agrotkindustrial.com/
STORAGE INSTRUCTIONS
Clean all the debris, all mud, dirt and grease. Replace all the blades at the same time and don’t try to weld or straighten damaged
blades; loss of integrity may result. Inspect the unit for bent, loose, cracked, damaged or missing parts, Order any parts
required, and make the necessary repairs to avoid delays when starting next season. Tighten all loose nuts, bolts, screws and hydraulic connections. Touch up all the unpainted and exposed areas with paint to prevent rust. Replace security labels and tags if damaged, or in unreadable condition. Connect the hydraulic couplers together or use the oil nuts to block the hydraulic
hoses. Check the motor for proper lubricant level. Apply a rust-preventive spray to all moving parts and to the bottom of the deck. Should put the device in the dry non-corrosive place. If in nude outside, will lessen
the lifetime of the unit.
P9
https://www.agrotkindustrial.com/
NOTES
P10
https://www.agrotkindustrial.com/
agrotkindustrial
