B09ZTPTNY8 Solar Motion Sensor Light

GUYIS SOLAR MOTION SENSOR LIGHT USER MANUAL

Brief Introduction

The GUYIS Solar Motion Sensor Light is a green energy and
wireless solar light that can be used in various outdoor settings
such as front-doors, gardens, yards, garages, patios, platforms,
sheds, parks, porches, steps, fences, driveways, farms and more. It
comes with an adjustable bracket that can be adjusted to meet
different needs and a high-sensitivity remote control for easy
settings change. The light is easy to install and charges during
the daytime, providing bright light automatically at night.

Specification

• Waterproof level: IP65
• Functional switch:
  1. Press ON/OFF for 3 seconds to turn on.
  2. First pattern: Body induction + dim light pattern.
• Infrared remote control:
  1. ON
  2. OFF
  3. Mode switch button – 6 levels to adjust the brightness
  4. ON
  5. OFF
  6. Mode switch button – 7 levels color temperature adjustable
     (warm white 2700k–white 6500k)

Usage Instructions

1. Before installation and use, please charge the solar lamp in
   the sun for 6-8 hours.
2. Please install the device facing the south and make sure the
   solar panel can receive good sunlight directly.
3. Press the ON button for 3 seconds to turn on the light and
   press mode switch to choose one mode you like.
4. Punch two suitable holes on the place where will be installed,
   insert the expansion pillar-hinges, screw up then hang up the
   light. Ideal height is 3-12 feet.
5. The light can be adjusted up and down, adjust the bracket
   angle.

Attentions

• As the light is solar powered, it is connected closely with
  weather, angle and strength of sunlight. Recommended to use Mode 2
  on remote for energy saving during fall or winter and cloudy
  periods.
• The battery lifetime is more than 5 years, do not put the
  battery in the fire to avoid explosion.
• Please keep the solar panel clean, because the lamp is charged
  by the solar panel. It is recommended to clean the solar panels
  every 3 months for easy and fast charging.

GUYIS
SOLAR MOTION SENSOR LIGHT USER MANUAL
Before installation and use, please charge the solar lamp in the sun for 6-8 hours

Brief Introduction 1. This light is a green energy and wireless solar
light. 2. With adjustable bracket, flexible angle can meet
different needs. 4. There is a high-sensitivity remote control,
you don’t need to climb up if want to change the settings ,which is very convenient. 5. No wires, easy to install,charging in the daytime, bright at night automatically. 6. Great outdoor solar lights for your front-door, garden, yard, garage,patio,platform,shed,park, porch, step, fence and driveway, farm and etc.
Specification:
Solar Panel : 5.5V/2.5W Battery: Lithium 3.7V/2200MAH Output: 4.5W LED:SMD2835 Luminous flux: 550lumen Induction angle: 120°
Induction distance1-5M Remote angle: 120° Remote distance: 1-5M Charging time: 6-8
Waterproof level:IP65

Functional switch: 1.Press “ON/OFF” for 3 seconds to turn on. 2.First pattem: Body induction +dim light patten
(While people go through the sensing area, the brightness will be strong. The light turns to dim after the people leave the area). 3.Press again, change to body induction mode (While people go through the sensing area, the brightness will be strong. The light turns off after the people leave the induction area). 4.Press the switch again: Always-on mode. It will always on at night, with no induction function, (Used in special places). 5.Press again, then tum off. Induction lighting time: Extended for 15 seconds after inducted,if the light induction mode delay time isn’t finished that induction once again, the timing will restart.

Infrared remeote control
A

ON

OFF

Mode switch button

6 levels to adjust the brightness

B

ON

OFF

Mode switch button

7 levels color temperature adjustable (warm white 2700k–wihte 6500k)

Take out the clear insulation sheet first when you use the remote control.

Installation
1. Please install the device facing the south and make sure the solar panel can receive good sunlight directly.
2. Press the ON button for 3s turn on the light and press mode switch to choose one mode you like.
3. Punch two suitable holes on the place where will be installed, insert the expansion pillar-hinges, screw up then hang up the light .Ideal height is 3-12 feet.

Attentions:
1. As the light is solar powered, it is connected closely with weather, angle and strength of sunlight. Recommended to use Mode 2 on remote for energy saving during fall or winter and cloudy periods.
2. The battery lifetime is more than 5 years,do not put the battery in the fire to avoid explosion.
3. Please keep the solar panel clean, because the lamp is charged by the solar panel. It is recommended to clean the solar panels every 3 months for easy and fast charging.

The light can be adjusted up and down, adjust the bracket angle.