T0661 Lavage Aluminum 2 Light Black Contemporary Outdoor Wall Lamp
Product Information
The product is a light fixture with a maximum capacity of 40W
Type A bulb (not included). It comes with a hardware package that
includes a mounting plate unit, mounting screw, wire connector, and
set screw. The product also has a cover and a spare parts list that
includes the mounting plate unit, mounting screw, wire connector,
assembly kit, and set screw. The product is intended for indoor use
only.
Product Usage Instructions
Before installing the light fixture, turn off the main power at
the circuit breaker. Also, consult local electrical codes for
wiring and grounding requirements.
- Unscrew the two set screws (D) and remove the mounting plate
unit (A) from the backplate. - Attach the mounting plate unit (A) to the outlet box by using
two mounting screws (B). Ensure that two set holes are lined up
horizontally to make the fixture level. - Attach the backplate of the fixture to the mounting plate unit
(A) by aligning holes, secure the two set screws (D) from the side
hole of the backplate into the hole in the side of the mounting
plate unit (A). Use silicone caulk compound to caulk completely
around where the backplate meets with the wall surface to prevent
water from seeping into the outlet box. - Remove the cover from the fixture.
- Install the bulbs (not included). See relamping label at socket
area or packaging for maximum wattage allowed. - Attach the cover back to the top of the fixture carefully.
- Turn on the power at fuse or circuit box.
If any parts are missing or damaged, refer to the spare parts
list for re-ordering. Note that the product is intended for indoor
use only.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
T0661
WWARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C)
Set screw (D)
Max. 40W Type A Bulb (not included)
Cover
Wire Connector (C) House Ground Wire Mounting Plate Unit(A) Green Ground Screw Outlet Box
Backplate Fixture Wire
Fixture
Mounting Screw (B)
Set Screw (D)
Max. 40W Type A Bulb (not included)
Page 1 / 2
221024
T
Installation Steps
Turn off the power at fuse or circuit box
1. Unscrew the two set screws (D) and remove the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Note: Make sure that two set holes are lined up horizontally to make the fixture level.
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wires (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wires (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with the green ground screw then depending on local code, connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Attach the backplate of the fixture to the mounting plate unit (A) by aligning holes, secure the two set screws (D) from the side hole of the backplate into the hole in the side of the mounting plate unit (A). Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.
5. Remove the cover from the fixture.
6. Install the bulbs (not included). See relamping label at socket area or packaging for maximum wattage allowed.
7. Attach the cover back to the top of the fixture carefully.
Turn on the power at fuse or circuit box
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Plate Unit (A)
Mounting Screw (B)
Wire Connector (C)
Assembly Kit 6594MM (1 SET)
Set screw (D)
A: 14″
A
B: 4-3/4″
C: 5-1/2″
B
C
Page 2 / 2
221024
