Ralph Lauren Northport Rl2566 32 Inch Linear Sconce Instruction Manual

Northport RL2566 32 Inch Linear Sconce

Product Information: Northport 32 Linear Sconce

The Northport 32 Linear Sconce (Item # RL2566) is a light
fixture designed for indoor and outdoor use. It should be installed
in accordance with all applicable, local installation codes, and by
a person familiar with the construction and operation of it, as
well as the hazards involved. The fixture comes with a mounting
plate (A & H), screws (D), and a fixture body (E).

Tools Required (not included):

  • Phillips Screwdriver
  • Slotted Screwdriver
  • Drill
  • Pencil
  • Hammer

Product Usage Instructions:

  1. Carefully remove all parts from the box. Place on a clean, soft
    surface.
  2. Remove mounting plate (A & H) from fixture (E) by removing
    screws (D).
  3. Install mounting plate (A) to junction box and secure with
    mounting screws (B).
  4. Using mounting plate (H) and fixture body as a guide, mark
    anchor locations on wall with a pencil.
  5. Drill pilot holes for anchors using a drill.
  6. Insert anchors into the holes and tap gently with a hammer
    until flush with the wall.
  7. Using screws (D), attach mounting plate (H) to wall
    anchors.
  8. Connect wires from fixture (E) to wires from junction box,
    following wiring diagram in the user manual.
  9. Secure wire connections with wire nuts and cover with
    electrical tape.
  10. Make sure all wire connections are tight, then carefully tuck
    into the junction box.
  11. Install fixture (E) to mounting plates (A & H) by securing
    with screws (D).

For Outdoor/Wet Location Installation:

Using silicon compound, apply a small bead where backplate meets
the wall to prevent water from entering. Note: Large gaps will need
to be corrected before applying silicon compound.

Care Instructions:

Clean only with a soft dry cloth or feather duster. Do not use
abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS

A BC D

E

Diagram 1

F

H GD

Northport 32″ Linear Sconce
Item # RL2566
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver

Slotted Screwdriver Drill

Pencil

Hammer

1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (A & H) from fixture (E) by removing
screws (D). 3. Install mounting plate (A) to junction box and secure with mounting
screws (B). 4. Using mounting plate (H) and fixture body as a guide, mark anchor
positions. NOTE: Carefully measure distance between mounting points for mounting plate (H) and junction box before moving to the next step. 5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (F) into the holes using hammer. 6. Install mounting plate (H) to wall and secure with wood screws (G) to anchors (F). 7. Wrap supply ground wire (bare copper) around the green grounding screw. Tighten. (See diagram 1) 8. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (C). 9. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (C). CAUTION: Do not reverse the hot and neutral connections.

ASSEMBLY INSTRUCTIONS

A BC D

E

Diagram 1

Northport 32″ Linear Sconce Item # RL2566
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Make sure all wire connections are tight, then carefully tuck into the junction box.
11. Install fixture (E) to mounting plates (A & H) by securing with screws (D).
FOR OUTDOOR/WET LOCATION INSTALLATION: 12. Using silicon compound, apply a small bead where backplate meets
the wall to prevent water from entering. NOTE: Large gaps will need to be corrected before applying silicon compound.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

F

H GD

Documents / Resouces

Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.


Related Manuals