SPARK10 Pro Smartphone
Product Information
TECNO SPARK 10 Pro
The TECNO SPARK 10 Pro is a smartphone featuring a 6.78-inch
HD+V/MDT Panda/BlackINCELL assembly display. It comes with a front
camera, volume keys, power key with a side fingerprint sensor,
earphone jack, USB port, and NFC functionality.
The device is powered by HiOS, which runs on AndroidTM OS. It
meets the government’s requirements for Specific Absorption Rate
(SAR) and complies with Part 15 of the FCC Rules.
Features:
- 6.78-inch HD+V/MDT Panda/BlackINCELL assembly display
- Front camera
- Volume +key and Volume -key
- Power key with side fingerprint sensor
- Earphone jack
- USB port
- NFC functionality
- HiOS running on AndroidTM OS
Product Usage Instructions
SIM/SD Card Installation
- Power off the mobile device.
- Refer to the picture provided in the user manual for SIM/SD
card installation.
Charging the Phone
You can charge your TECNO SPARK 10 Pro using a charger or by
connecting it to a computer using a USB cable (included with the
phone).
Note: Only use TECNO charger and cables to
avoid damaging the device and invalidating the phone warranty.
FCC Caution
The TECNO SPARK 10 Pro complies with Part 15 of the FCC Rules.
Please note the following:
- This device may not cause harmful interference.
- This device must accept any interference received, including
interference that may cause undesired operation. - Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
Trademark: AndroidTM is a trademark of Google
LLC.
TECNO SPARK 10 Pro
User Manual
Explosion diagram specification
1 6.78HD+V/MDT Panda/BlackINCELL assembly
3 LCM CONDUCT FOAM 1 5 FRG FRAPHITE 7 P_SENSOR MYLAR 9 FCAM SEAL FOAM 1 11 PL GUIDE 13 SIDEKEY FPC CONDUCT 15 ADHESIVE FLASH 17 WATERPROOF FOAM 19 SIDEKEY FPC 21 REC FOAM 23 CONDUCTIVE SPONGE 25 AD9 H831 FCAM 27 Receiver 29 REC FPC 31 SCREW 33 FRO CAM PRESS FOAM 35 VICE CAM
2 LCM CONDUCT FOAM 2
4 REC DECO 6 FLASH MYLAR 8 FCAM SEAL FOAM 1 10 FCAM SEAL FOAM 1 12 SIDEKEY FPC CONDUCT 14 PL RUBBER 16 ADHESIVE P SENSOR 18 WATERPROOF MEMBRANE 20 SIDEKEY FPC 22 REC FOAM 24 SIM FOAM 26 BAT ADHESIVE 1 28 COAXIAL 30 PCBA 32 Main Back cam 34 VICE CAM 36 CARD DOO
37 MAIN CAM FOAM 39 FLA GUIDE 41 FLA GUL FOAM 43 VICE CAM LENS ADHESIVE 45 MAIN CAM LENS 47 BAT PORON 49 FLA PCB GRAPHITE 51 SCREW 53 CHARGER SHIELD GRAPHITE 55 BAT GRAPHITE 57 FG BTB PRESS FOAM 59 VICE CAM BTB PRESS FOAM 61 BATTERY BTB PRESS FOAM 63 ANT MAIN 65 FINGER 67 MOTO 69 SCREW 71 LCM FPC ADHESIVE 73 SCREW 75 SPEAKER FOAM 77 JACK RUBBER 79 SPEAKER RUBBER 81 SPEAKER CONDUCT FOAM 83 MIC FOAM 85 FRP HSG
38 FLA GUL ADHESIVE 40 REAR CAM COPPER FOIL 42 MAIN CAM LENS ADHESIVE 44 FLA LENS ADHESIVE 46 MAIN CAM LENS 48 RF SHIELD GRAPHITE 50 FLA PCB GRAPHITE 52 CHARGER SHIELD GRAPHITE 54 CHARGER SHIELD GRAPHITE 56 PEAR 58 VICE CAM BTB PRESS FOAM 60 VICE CAM SUPPORT FOAM 62 BATTERY BTB PRESS FOAM 64 FINGER 66 SPK FPC 68 SUB PCBA 70 SCREW 72 BAT ADHESIVE 3 74 BOX 76 JACK RUBBER 78 USB RUBBER 80 USB CONDUCT FOAM 82 MIC RUBBER 84 SPEAKER NET 86 WATERPROOF MALAR
Know your phone
1. Front camera 2. Volume +key 3. Volume -key 4. Power key & side fingerprint sensor 5. Earphone jack 6. USB port 7. NFC
SIM/SD card installation
1. Power off mobile. 2. Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Information to user. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information: This mobile phone meets the government’s requirements for
exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: KI7 (FCC ID: 2ADYY-KI7) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.320W/kg and when properly worn on the body is 0.603W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
HiOS runs on AndroidTM OS. Android is a trademark of Google LLC.
