Ryobi Rll10rd Red Cross Line Laser Instruction Manual

RLL10RD Red Cross Line Laser

Product Information

Product Usage Instructions

1. Before assembling, operating, and maintaining the product, it
   is essential to read the instructions in the user manual.
2. The product is intended for determining and verifying
   horizontal and vertical lines only. Do not use it for any other
   purpose.
3. Ensure that you are an adult who has read and understood the
   instructions and warnings in the user manual before using the
   product.
4. Avoid direct eye exposure to the laser beam. Do not stare into
   the beam or direct it towards other people.
5. Keep the product away from children and do not allow them to
   operate the laser.
6. Avoid using the product on reflective surfaces as the laser
   beam may be reflected and cause harm to the operator or other
   persons.
7. Store the product indoors, away from dust, liquids, high
   humidity, substantial knocks, continuous vibration, and extreme
   temperatures.
8. In case the laser beam hits your eye, immediately close your
   eyes and turn your head away from the beam.
9. Position the laser beam in a way that it does not
   unintentionally blind you or others.
10. Avoid looking into the laser beam using magnifying optical
    devices such as binoculars or a telescope as it increases the risk
    of eye injury.
11. If you use laser goggles to enhance visibility, note that they
    will not protect your eyes against laser radiation.
12. Do not remove or deface warning labels on the product.
13. Do not disassemble the product or subject it to heavy impact or
    dropping. Check the accuracy of the laser if it has been dropped or
    subjected to mechanical stresses.
14. Do not operate the product in explosive areas or extreme
    environments.

RLL10RD RLL15GN

IMPORTANT! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product.
Subject to technical modifications.
INTENDED USE
The cross line laser is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.
The product is intended for determining and verifying horizontal and vertical lines.
Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.
CROSS LINE LASER SAFETY WARNINGS
Laser radiation. Do not stare into beam. Class 2 laser product.
Risk of severe eye injury if the laser beam is directed at persons or animals. Avoid direct eye exposure.
Do not direct the laser beam towards other people.
Do not operate the product around children or allow children to operate the laser.
Avoid using the product on reflective surfaces. The laser beam may be reflected at the operator or other persons.
Store the product indoors and avoid substantial knocks, continuous vibration or extreme temperatures.
Always keep the product away from

dust, liquids and high humidity. They may damage internal components or affect accuracy.
If laser beam hits your eye, you must close your eyes and immediately turn your head away from the beam.
Do not position the laser beam so that it unintentionally blinds you or others.
Do not look into a laser beam using magnifying optical devices such as binoculars or a telescope. This will increase the level of eye injury.
If you use laser goggles to enhance the visibility of the laser beam, note that they will not protect your eyes against laser radiation.
Do not remove or deface warning labels on the product.
Do not disassemble the product.
Avoid heavy impact to or dropping of the laser. The accuracy of the laser should be checked before use if it has been dropped or subjected to other mechanical stresses.
Do not operate the product in explosive areas or in extreme environments.

SELF-LEVELLING LED INDICATOR

LED indicator Explanation

Green

Self-leveling is complete.

Self-leveling is not

Red

successful; laser line blinks. Place the product in a

horizontal position of +/-3°.

MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be

2 Original Instructions

damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
For greater safety and reliability, all repairs should be performed by an authorised service centre.

SYMBOLS ON THE PRODUCT

V

Volts

Direct current

Regulatory Compliance Mark (RCM). Product meets applicable regulatory requirements.

Please read the instructions carefully before starting the machine.

Class 2 laser beam. Do not stare into the laser beam.

Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be coll ected separately. Waste batteries, waste accumulators, and light sources have to be removed from the equipment. Check with your local authority or retailer for recycling advice and collection point. According to local regulations, retailers may have an obligation to take back waste batteries and waste electrical and electronic equipment free of charge. Your contribution to the reuse and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw materials. Waste batteries, in particular containing lithium, and waste electrical and electronic equipment contain valuable and recyclable materials, which can adversely impact the environment and the human health if not disposed of in an environmentally compatible manner. Delete personal data from waste equipment, if any.
SYMBOLS IN THIS MANUAL

Note

Do not stare into the laser beam.
Original Instructions 3

4 Know your product

Exit window for laser beam Self-levelling LED indicator Battery door
On/off switch
1/4″ tripod mount Clamp Battery
Operator’s manual

1

2

3

3

Getting started 5

1
2

2
2 3

3

2

6 Operation

PRODUCT SPECIFICATIONS

Cross Line Laser Model Accuracy Laser wavelength Fan angle Colour Working range Laser class Projection Self-Leveling Time Self-Leveling Angle Operating Time Battery technology Supply voltage Operating temperature range Storage temperature range Dimensions

RLL10RD ±0.5 mm/m 635nm ± 5nm >100° Red 10 m 2, <1mW Cross Line 2s ~ 5s ± 3° 24 h 2 x AA LR6 Alkaline 2 x 1.5V 0°C ~ 40°C -20°C ~ 70°C L69 x W63 x H72 mm

RLL15GN ±0.5 mm/m 520nm ± 10nm >100° Green 15 m 2, <1mW Cross Line 2s ~ 5s ± 3° 6 h 2 x AA LR6 Alkaline 2 x 1.5V 0°C ~ 40°C -20°C ~ 70°C L69 x W63 x H72 mm

Imported by: Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia
Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
20230303v1