Solidrun Srg0400-wbt Solidsense Installation Guide (+ PDF)

The SolidRun SolidSense SRG0400-WBT module uses a 50-ohm line
design. Fine tuning of return loss and other parameters can be
performed using a matching network. However, it is required to
check Class1 change and Class2 change as defined by the
authorities.

The concrete contents of the check are as follows:

The antenna type should be the same as the specified antenna
type.
The antenna gain should be lower than the specified gain.
The emission level should not get worse.

The recommended antenna for the SRG0400-WBT module is the
ANT16244DT Loop antenna by TDK Corporation with a gain of +2.1 dBi
at 2442 MHz and +3.5 dBi at 5150 MHz.

4. Supply Voltage

Parameter	Min.	Typ.	Max.	Unit
Operating Temperature*1	-30	25	+85	Deg.C
Supply voltage VBAT	3.2	3.3	4.8	V
Supply voltage VIO*2	1.62	3.63	V

5. Theory of Operation-Channel List

The operating frequency of the SRG0400-WBT module is 2.4 GHz. It
supports the following modes:

Frequency of operation	Mode
2.4 GHz	11b/g/n (HT20)
BT	W52
5 GHz	11a/n ((V)HT20)
5 GHz	11a/n ((V)HT20)

Note: End users cannot modify the software because the firmware
and driver are installed in the device.

6. Theory of Output Power List

This specification is limited to use with the following output
power settings:

Frequency	Output Power Setting [dBm]
2.4GHz WLAN	—
5GHz WLAN	—

User Manual for FCC

This section provides information regarding the FCC modular
approval of the SRG0400-WBT module.

Model Name: LBEE5HY1MW

Model Number: SRG0400-WBT

FCC ID: 2BA24LBEE5HY1MW

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.

View Fullscreen

SolidRun SolidSense SRG0400-WBT
SRG0400-WBT Installation Manual
Model name: LBEE5HY1MW Model number (HVIN): SRG0400-WBT Product description: Communication Module
FCC identifier of this product is as follows. FCC ID: 2BA24LBEE5HY1MW ISED certification number of this product is as follows. IC: 12107A-LBEE5HY1MW

SolidRun SolidSense SRG0400-WBT
1. Land Pattern (Recommended)

SolidRun SolidSense SRG0400-WBT
2. PIN Layout

SolidRun SolidSense SRG0400-WBT

3. Antenna
It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check “Class1 change” and “Class2 change” which the authorities define then.

The concrete contents of a check are the following three points. 1) It is the same type as the antenna type of antenna specifications. 2) An antenna gain is lower than a gain given in antenna specifications. 3) The emission level is not getting worse.

50-ohm line(microstrip line length)

Antenna Antenna type: 50-ohm feed line length:

Loop antenna We test it at 0mm as a representative

SolidRun SolidSense SRG0400-WBT

Recommended antenna

This Antenna Specification is based on Keyence’s requirement..

Model name SRG0400-WBT

· Antenna Model Name :

ANT16244DT

· Antenna type :

Loop antenna

· Antenna manufacture :

TDK Corporation

· Antenna gain :

+2.1 dBi @ 2442 MHz

+3.5 dBi @ 5150 MHz

· Frequency :

24002483.5 MHz, 51505850 MHz

SolidRun SolidSense SRG0400-WBT
Recommended antenna characteristics

SolidRun SolidSense SRG0400-WBT

4. Supply Voltage

Parameter

Operating Temperature*1

Supply voltage

VBAT VIO*2

Min.

Typ.

Max.

Unit

-30

+85

Deg.C

3.2

3.3

4.8

1.62

3.63

*1: Surface temperature of the shield case Functionality is guaranteed but specifications require derating at extreme temperatures *2: VIO don’t influence the RF characteristic. Tolerance of 1.8V and 3.3V is ±10%.

5. Theory of Operation-Channel List
Theory of Operation-Software Security and Channel List

Frequency of operation

2.4 GHz

11b/g/n (HT20)

W52

11a/n ((V)HT20)

W53

11a/n ((V)HT20)

24122462 MHz 24022480 MHz 51805240 MHz 52605320 MHz

Scan Active N/A Active Passive

Ad-hoc mode Yes N/A Yes No

* This specification is limited to use in the above frequency bands and modes. Notes: End users cannot modify the software because F/W & driver are installed in device.

SolidRun SolidSense SRG0400-WBT
6. Theory of Output Power List This specification is limited to use with the following output power settings. Limited output power setting. [dBm] 2.4GHz WLAN
5GHz WLAN

SolidRun SolidSense SRG0400-WBT

User Manual for FCC
Regarding FCC modular approval of SRG0400-WBT
Model Name: LBEE5HY1MW Model Number: SRG0400-WBT FCC ID: 2BA24LBEE5HY1MW

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: 2BA24LBEE5HY1MW or Contains FCC ID: 2BA24LBEE5HY1MW

SolidRun SolidSense SRG0400-WBT
The following statements must be described on the user manual of the host device of this module;
FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
Frequency Tolerance: ±20 ppm
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.
When installing it in a portable equipment. Please describe the following warning to the manual. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. SRG0400-WBT has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth V5.0(BDR/EDR/LE)). Class II permissive change application is necessary using the SAR report. Please contact SolidRun. Portable equipment: Equipment for which the spaces between human body and antenna are used within 20 cm. Mobile equipment: Equipment used at position in which the spaces between human body and antenna exceeded 20 cm.

SolidRun SolidSense SRG0400-WBT
SRG0400-WBT User Manual for ISED
PMN: LBEE5HY1MW HVIN: SRG0400-WBT ISED certification number: 12107A-LBEE5HY1MW
Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure).
The following information must be indicated on the host device of this module. Contains IC: 12107A-LBEE5HY1MW
The following statements must be described on the user manual of the host device of this module;
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B).
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempt de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Cet appareil numérique de la Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
*When is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.
In case of the final product which can be carried around to outdoor. The following indication is necessary to the final product. When the AP function is used in W52; At the time of a channel setting of W52, please indicate “for indoor use only”. During connecting, please show the channel number which connects.

SolidRun SolidSense SRG0400-WBT
And please indicate that the end user may find out “for indoor use only channel”. When the STA function is used in channel 52, 54, 58, at the time of the channel 52 or 54 or 58 setting, please indicate “for indoor use only channel”. During connecting, please show the channel number which connects. And please indicate that the end user may find out “for indoor use only channel”. If the antenna of the end product is removed, please describe the follow warning on the manual of the end product which contains this module.
This radio transmitter (IC Number: 12107A-LBEE5HY1MW) identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. : 2.4GHz Loop Gain: +2.1 dBi : 5GHz Loop Gain: +3.5 dBi
Le présent émetteur radio (IC Number: 12107A-LBEE5HY1MW) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur. Type d’antenne : 2.4GHz Loop Gain: +2.1 dBi : 5GHz Loop Gain: +3.5 dBi
If the final product use the following frequency, please note that there is a limit.
For indoor use only (5150-5250MHz band and channel 52, 54, 58)
Pour usage intérieur seulement (5150-5250MHz band and channel 52, 54, 58)
The following statements must be described on the user manual of the host device of this module; Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
La transmission des données est toujours initiée par le logiciel, puis les données sont transmises par l’intermédiaire du MAC, par la bande de base numérique et analogique et, enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le MAC. Ce sont les seuls moyens pour qu’une partie de la bande de base numérique active l’émetteur RF, puis désactive celui-ci à la fin du paquet. En conséquence, l’émetteur reste uniquement activé lors de la transmission d’un des paquets susmentionnés. En d’autres termes, ce dispositif interrompt automatiquement toute transmission en cas d’absence d’information à transmettre ou de défaillance.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.

SolidRun SolidSense SRG0400-WBT
When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux radiations ISED CNR-102 établies pour un environnement non contrôlé. Une distance de séparation d’au moins 20 cm doivent être maintenue entre l’antenne de cet appareil et toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.