Luca Rectangular Wall Sconce
Product Information
The Luca Wall Mount is a light fixture designed for wall or
ceiling installation. It comes with all the necessary components
for installation, including a backplate, wago clips, hex key,
bulbs, mounting screws, and canopy set screws.
Please note that the following tools are not included and will
be required for installation: standard wire stripper and Phillips
head screwdriver.
Before starting the installation process, it is essential to
turn off the electrical power source to avoid any electrical shock
risk. We recommend consulting a qualified electrician for
assistance.
Product Usage Instructions
- Step 1: Turn off electrical power at the main fuse box or
circuit panel before beginning installation. - Step 2: Mount the backplate (A) to the junction box using a
Phillips head screwdriver to tighten the mounting screws (E). - Step 3: Use the wago clips (B) to connect the fixture’s wires
to the corresponding wires from the junction box in the wall or
ceiling. The white wire is neutral, the black wire is live, and the
green/yellow wire is ground. One ground wire should be attached to
the backplate (A), and the other should come from the junction box.
If needed, use a wire stripper to remove 3/8 of the insulation from
each wire before inserting them into the corresponding wago
clip. - Step 4: Align the holes of the backplate with the holes of the
canopy cover attached to the fixture (G) and secure the set screws
(F) by tightening them using the included L-shaped hex key
(C). - Step 5: Gently screw in the included lightbulb (D) into the
sockets of the fixture (G).
Luca Wall Mount
How to Install Your New Light Please check that you received all of the components pictured in this guide. Reach out to us if anything is missing. It’s very rare, but it happens. Don’t forget to turn off the electrical power source.
Tools you will need that aren’t included: standard wire stripper, Phillips head screwdriver.
CAUTION Electrical shock risk. Turn off electrical power at the main fuse box or circuit panel before beginning installation, servicing the light, or installing accessories. We recommend working with a qualified electrician familiar with the type of work you’d like done.
ATTENTION Risque de choc électrique. Coupez l’alimentation électrique au niveau de la boîte à fusibles principale ou du panneau de circuits avant de commencer l’installation, l’entretien de la lumière ou l’installation d’accessoires. Nous vous recommandons de travailler avec un électricien qualifié familier avec le type de travail que vous souhaitez effectuer.
Contents
Part A Backplate
Part B Wago Clips (x3)
Part C Hex Key
Part D Bulb (x2)
Part E Mounting Screws (x2)
Part F Canopy Set Screws (x2)
Part G Luca Fixture
Assembly Guide
1 of 3
incommonwith.com
Luca Wall Mount
Step 1: Turn off electrical power at the main fuse box or circuit panel before beginning installation.
Step 2: Mount the backplate (A) to the junction box using a phillips head screwdriver to tighten the mounting screws (E).
A
E
!
Step 3: Use the wago clips (B) to connect the fixture’s wires to the corresponding wires from the junction box in the wall or ceiling. White is neutral; Black is live; Green/ Yellow is ground. One ground wire will be attached to the backplate (A), the other ground wire should come from the junction box. If needed use a wire stripper to remove 3/8″ of the insulation from each wire before inserting them into the corresponding wago clip.
Step 4: Align the holes of the backplate with the holes of the canopy cover attached to the fixture (G) and secure the set screws (F) by tightening using the included L-shaped hex key (C).
C F
B
G A
Assembly Guide
2 of 3
incommonwith.com
Luca Wall Mount
Step 5: Gently screw in the included lightbulb (D) into the sockets of the fixture (G).
G D
Assembly Guide
3 of 3
incommonwith.com
In Common With
