dji Action 2 GoPro Hero 10 Dual Screen Combo Camera Instructions

dji Action 2 GoPro Hero 10 Dual Screen Combo Camera Instructions

Safety at a Glance

  Please read this entire document and visit http://www.dji.com/action-2 to view the user manual, other documents, and the tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may result in personal injury, damage to your DJI OSMOTM product, or other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of DJI OSMO.

By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of this document. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. This product is not intended for use by children without direct adult supervision.

WARNING

1. DJI ActionTM 2 contains magnets. Keep the camera unit away from magcards, IC cards, hard disks, RAM chips, implantable medical devices such as pacemakers, and other devices to avoid interference.
2. All the holes on the camera unit have built-in waterproof material. DO NOT poke the holes. Clean the camera unit with a clean, dry cloth after using under water.
3. DO NOT attach the camera unit to the front touchscreen module when there is any dust or water on the expansion ports. Otherwise, the camera unit may corrode or short-circuit.
4. Put out any product fire using water, sand, fire blanket, or a dry powder fire extinguisher.
5. The product should be used in temperatures from 0º to 40º C (32° to 104° F). Use of the product in environments above 40º C (104° F) can lead to a fire or explosion. Use of the product below 0º C (32° F) can lead to permanent damage.
6. Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
7. DO NOT drop or strike the product. DO NOT place heavy objects on the product.
8. DO NOT heat the product. DO NOT put the product in a microwave oven or in a pressurized container.
9. DO NOT leave the product near heat sources such as a furnace or heater. DO NOT leave the product inside of a vehicle on hot days. The ideal storage temperature is 22º C to 28º C (72° to 82° F).
10. DO NOT store the product fully discharged for an extended period. Otherwise, it will over discharge, which will lead to permanent damage.

CAUTION

1. Intricate components inside DJI Action 2 may be damaged upon impact and cause the camera unit to malfunction.
2. Keep the lens glass clean. Sand and dust may damage the lens glass. Clean DJI Action 2 with a clean, dry cloth.
3. Make sure to be careful if the lens glass breaks.
4. Keep DJI Action 2 away from sand and dust. Wash the camera unit if the holes are blocked by sand, dust, or any other substance.
5. DO NOT poke the USB-C port or microSD card slot
6. DO NOT expose DJI Action 2 to extreme cold or hot temperature. Otherwise, the operating time and functionality may be negatively affected.
7. DO NOT use DJI Action 2 during lightning storms.
8. DO NOT disassemble or repair DJI Action 2 by yourself.
9. DO NOT use DJI Action 2 inside hot springs. DO NOT allow DJI Action 2 to come into contact with corrosive or unknown liquids.
10. When attaching DJI Action 2 to the roof or window of a car, the camera unit may fall off if the car travels too fast, the surface is not clean, or there is bad weather such as high winds or a thunderstorm.
11. The front touchscreen module is not waterproof. The waterproof case is required when using the front touchscreen module with the camera unit under water.
12. Charge DJI Action 2 when the battery level is low. Storing the camera unit for more than four months with low battery will reduce the battery life.

Specifications

Compliance Information

FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI Action 2
Model Number: MC211
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above
mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; where applicable, antenna type(s), antenna models(s), and worst case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Action 2) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance

EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Action 2) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.

A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

This device is restricted to indoor use when operating in the 5150-5250MHz frequency range in all EU/EFTA member states and Turkey.

Brazil Warning message

To view the full compliance information, slide down on the camera view, tap the settings icon, and scroll through to select Compliance Info.

This content is subject to change without prior notice.
OSMO is a trademark of DJI OSMO.
Copyright © 2021 DJI OSMO All Rights Reserved.

Read More About This Manual & Download PDF:

Documents / Resources

dji dji Action 2 GoPro Hero 10 Dual Screen Combo Camera [pdf] Instructions Action 2, GoPro Hero 10 Black Camera, Action 2 GoPro Hero 10 Black Camera, Hero 10 Black Camera, Camera, dji Action 2 GoPro Hero 10 Dual Screen Combo Camera, Dual Screen Combo Camera