honoto Chorus 1 True Wireless Earbuds
Operation
| Item | Cooperation | LED |
| Power On | Take out the earphones from the charging case | Red and blue lights flash alternately |
| Power Off | Put back to charging case | Red light on |
| Pairing | After take out from the charging case, it will be in pairing mode(it will automatically enter the single ear pairing state after 10 seconds) | Red and blue lights flash alternately |
| Connection | Choose the Chorus 1 when you search it | Blue light flashes every 5 seconds |
| Disconnection | Disconnect between phone and earphones, it will enter the pairing mode | Red and blue lights flash alternately |
| Re-connection | Earphones paired automaticly | / |
| Turn off automatically if no connection | If no connection in 10 minutes, it will turn off automatically | LED light off |
| Charging | Put earphones back to charging case | Red light on |
| Finish charged | Earphones in charging case | LED light on |
| Low power alarm | Voice alarm occurs when power is below 3.3V | Red light flashes once every 5 secones |
| Clear pairing | Press and hole the touch button for 8 seconds when the earphones enters pairing mode | Red light flashes 2 times |
Earplug Selection
The sound quality will be affected by whether the earplugs are selected at right size, and the correct wearing will make you feel comfortable. Since different person’s ear type is different, we offer several different sizes of earplugs. Please choose the earplugs that are suitable for your ear type. We recommend you to try the smallest earplugs first and then try the bigger ones until you find the best and ensure the earplugs are not easily fall off.
Earplugs Cleaning
- It is important to keep the earplugs clean for safe and healthy use.
Important notice: please remove the earplugs from the earphones first and then try cleaning the earplugs. - Tightly hold the earplugs with one hand, tightly hold the earphones with the other hand, and remove the earplugs from the earphones carefully.
- Use a piece of wet cloth with warm water and soft soap to clean the dirt on the earplugs. Do not use powerful detergent.
- Rinse the earplugs and put them back to the earphons until they are completely dry.
- Carefully push the earplugs back to the earphones to ensure they are completely reset.
Maintenance And Storage
It is important to keep the earbud clean for safe and healthy use.
- Do not wear the in-ear earbuds that are dirty.
- When the earbud are out of use, please always store it in the clean dry environment.
- Do not store it with other articles, to avoid contamination.
- Avoid storing it in the environment that is too hot or too cold.
- Avoid contact with liquid, and avoid extreme temperature or high humidity environment.
- Do not dismantle the earbud in an unprofessional and nonstandard manner, to avoid sound bias of the earbud.
Frequently Asked Questions
Bad sound quality
- Please confirm if the earplugs are tightly fit in the ear.
- Please try to change a player or music sources.
Bad noise cancellation effect
- Please confirm if the earplugs cannot be tightly plugged . If so, please replace with the silicone cover of a different size delivered.
- Plearse confirm if the earphones are correctly worn.
No sound or sound change
- Please confirm if the current device supports this product.
- Please try to change a player or music sources.
Specification
- Model number: Chorus 1
- Bluetooth version: V5.0
- Wired Charging Input: 5V 1000MA
- Wireless Charging Input: 5V 300MA
- Frequency response range: 20Hz-20KHz
- Earphones battery capacity: 3. 7V /35mAh
- Charging case battery capacity: 3.7V/400mAh
- Working time: About 3 hours
- Earphones charging time: About 1 hour
- Charging case charging time: About 1 hour
- Bluetooth transmission distance: 10 meters (unobstructed enviroment)
- Bluetooth protocol: A2DP/AVRCP/HFP/SDP/SPP
Customer Support
[email protected]
www.honoto.com
FCC statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
