PS-C41RT Professional In-Ceiling Speaker
Product Information
PS-C41RT | PS-C61RT Professional Series In-Ceiling Speaker
Manual
The Sonance Professional Series In-Ceiling Speakers PS-C41RT and
PS-C61RT are designed for use in commercial environments and
deliver true full range fidelity, wide dispersion, and a smooth
power response. The speakers come with a polymer composite UL94V-0
sealed enclosure, a transformer tap and bypass selector, a tuning
port, a high excursion woofer, and a one-piece paintable grille
with magnetic retention. The speakers also feature seismic
attachment, an integrated back can connector cover, a Euroblock
connector with loop through, an inside cover cable and flexible
conduit clamp, and reversible Roto-LockTM toggle feet.
Product Usage Instructions
Before attempting to use the PS-C41RT | PS-C61RT In-Ceiling
Speakers, it is important to read the entire user manual and heed
all warnings and instructions. The product is intended to be
installed by professional AV integrators and installers only. It is
the installer’s responsibility to ensure that the product is
installed in accordance with local building codes and regulations.
Consult a local authority for specific requirements, regulations,
and building codes of the jurisdiction in which this product is to
be installed.
Product Preparation:
When selecting wire for your installation, refer to the wire
gauge chart (see Figure 1) provided in the user manual. It is
important to choose the appropriate wire gauge to prevent negative
effects on sound quality and maximum output level of the
system.
Amplifier Selection:
Choose an amplifier with an appropriate power rating for the
PS-C41RT | PS-C61RT In-Ceiling Speakers.
Wire Selection:
Select wire with the appropriate gauge as per the wire gauge
chart (see Figure 1) provided in the user manual.
70V/100V System:
When using a 70V/100V system, ensure that the transformer tap
and bypass selector is set according to the system
requirements.
8 Ohm System:
When using an 8 ohm system, ensure that the transformer tap and
bypass selector is set to bypass.
Speaker Placement:
Choose a suitable location for speaker placement. Refer to the
user manual for guidelines on speaker placement.
Grille Painting:
The one-piece paintable grille can be painted to match the
ceiling or wall color. Refer to the user manual for instructions on
grille painting.
Standard Installation:
Refer to the user manual for instructions on standard
installation of the PS-C41RT | PS-C61RT In-Ceiling Speakers.
Wiring:
Refer to the user manual for instructions on wiring the PS-C41RT
| PS-C61RT In-Ceiling Speakers.
Drop Ceiling Installation:
Refer to the user manual for instructions on drop ceiling
installation of the PS-C41RT | PS-C61RT In-Ceiling Speakers.
Technical Specifications:
Refer to the user manual for technical specifications of the
PS-C41RT and PS-C61RT In-Ceiling Speakers.
Certifications & Safety Agency:
The PS-C41RT | PS-C61RT In-Ceiling Speakers are certified by
various safety agencies. Refer to the user manual for a list of
certifications and safety agencies.
Technical Assistance & Service:
For technical assistance and service, refer to the user manual
for contact information.
Warranty:
The PS-C41RT | PS-C61RT In-Ceiling Speakers come with a
warranty. Refer to the user manual for warranty details.
PS-C41RT | PS-C61RT PROFESSIONAL SERIES IN-CEILING SPEAKER
MANUAL
PROFESSIONAL SERIES IN-CEILING SPEAKERS
PS-C41RT | PS-C61RT
TABLE OF CONTENTS
2 Important Safety Instructions & Box Contents 3 Product Description 3 Product Features 4 Product Preparation 4 Amplifier Selection 4 Wire Selection 4 70V/100V System 4 8 ohm System 4 Speaker Placement 5 Grille Painting 6 Standard Installation 6 Wiring 7 Drop Ceiling Installation 8 Technical Specifications PS-C61RT 9 Technical Specifications PS-C41RT 10 Certifications & Safety Agency 10 Technical Assistance & Service 11 Warranty
IMPORTANT SAFETY INSTRUCTIONS
This product is intended to be installed by professional AV integrators and installers only. This product manual is intended to serve as a general guideline for most applications. It is the installer’s responsibility to ensure this product is installed in accordance with local building codes and regulations. Consult a local authority for specific requirements, regulations, and building codes of the jurisdiction in which this product is to be installed.
READ THIS DOCUMENT IN ITS ENTIRETY BEFORE ATTEMPTING USE.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near a heat source such as radiators, heat registers, stoves, fireplaces, or other apparatus (including amplifiers) that produce heat.
8. To be installed in indoor locations only.
9. Only use attachments/accessories specified by Sonance.
10. Refer all servicing to qualified service personnel.
BOX & CONTENTS
(2) PS-C41RT, or PS-C61RT (2) Speaker Grille in White (Black Optional) (4) Tile Support Rails (2) C-Ring (1) Cutout Template
2
PRODUCT DESCRIPTION
From Sonance, the company that created the architectural audio category, comes a range of professional loudspeakers that set a new benchmark in sound quality and aesthetics for commercial environments.
Sonance Professional Series includes a range of InCeiling, Pendant and Surface Mount speakers that deliver true full range fidelity, extremely low distortion, wide dispersion and a smooth power response. The range also shares consistent voicing, ensuring seamless sonic integration when used together throughout a space.
The In-Ceiling speakers feature a one-piece bezel-less grille that is magnetically secured and allows for a one-step painting process to simplify installation and minimize visual distraction. The optional Square Grille Adapter allows the speakers to match the aesthetic of square downlights and HVAC grilles. Sealed UL94V-0 polymer composite enclosures, cable and flexible conduit clamping, seismic attachment and connecter cover allow them to be installed in commercial environments where UL 1480A and UL 2043 are required by code. Available in 4″, and 6.5″ – all shipped with white grille. Optional round and square black grilles are also available.
PRODUCT FEATURES
Polymer Composite UL94V-0 Sealed Enclosure
Transformer Tap and Bypass Selector Tuning Port High Excursion Woofer
One Piece Paintable Grille with Magnetic Retention
Seismic Attachment Integrated Back Can Connector Cover Euroblock Connector with Loop Through Inside Cover Cable and Flexible Conduit Clamp
Reversible Roto-LockTM Toggle Feet
3
PRODUCT PREPARATION
AMPLIFIER SELECTION When choosing an amplifier, the maximum number of speakers and the output level of each speaker must be known. The sum of the tap settings should never exceed 80% of the amplifier’s rated output. For example, if there are 5 speakers and the taps are set at 15 watts, the load would be 75 watts (5 x 15 watts = 75 watts). To arrive at the needed power for this number of speakers, simply divide the total load by 0.8. In this case, 75 / 0.8 = 93.75 watts. Therefore, a standard 100 watt amp would safely drive this load. To calculate the amount of usable power an amp offers, simply multiply the rated output by 0.8, i.e., 100 watts x 0.8= 80 watts.
WIRE GAUGE 70V/100V SYSTEM The most common wire used on commercial 70 volt systems is 18 gauge, 2 conductor, stranded, and jacketed without a shield. The wire starts at the amplifier location and is paralleled at each speaker location.
Wire length using 18 gauge is appropriate up to 700 feet with a 100 watt load. If you double the load (sum of your tap settings), you will reduce the footage by half, to 350 feet. Conversely, if you halve the load, you may double the acceptable wire length, i.e., a 50 watt load is safe over 1400 feet of 18 gauge. Stepping up to 16 gauge wire extends the allowable run length by approximately 35%. For example, a 100 watt load can go 700 feet on 18 gauge; the same load may be placed on 1100 feet of 16 gauge.
WIRE GAUGE 8 OHM SYSTEM When using Sonance Professional Series loudspeakers in an 8 Ohm system, the total wire resistance should be less than 10% of the speaker impedance. The speakers are nominally 8 Ohms impedance, so your total wire resistance should be no more than 0.8 Ohms.
In simple terms, the extra resistance from the wire will have a very negative affect on the sound quality of the speaker. The sound can be less dynamic, definition of bass frequencies can be reduced, and in extreme cases, the high frequencies can be attenuated. Amplifier power is also wasted in the wire, reducing the maximum output level of the system.
Please refer to the following chart (see Figure 1) when deciding on the appropriate wire gauge for your installation.
Wire Resistance in Ohms vs. Length of Cable Run
Distance in Feet 50′ 100′ 150′ 200′ 250′ 300′
20 Gauge
0.86 1.73 2.59 3.45 4.32 5.18
18 Gauge
0.65 1.30 1.94 2.59 3.24 3.89
16 Gauge
0.43 0.85 1.28 1.71 2.14 2.56
14 Gauge
0.27 0.54 0.81 1.08 1.35 1.62
12 Gauge
0.17 0.34 0.51 0.68 0.85 1.02
Figure 1: Wire Resistance
SPEAKER PLACEMENT
Sonance Professional Series speakers possess extremely smooth and predictable off-axis frequency response. The chart below (see Figure 2) shows how far apart the speakers can be placed in a distributed audio system. The calculations are based on +/- 45 degrees of coverage from the speaker, and listener ear heights of 62″ for standing and 40″ for seated.
SPEAKER SPACING
COVERAGE AREA
COVERAGE AREA
Speaker Spacing in Feet for a Distributed Audio System
8′ Ceiling
Standing Listener Seated Listener 5.7′ (1.7m) Apart 9.5′ (2.9m) Apart
10′ Ceiling
9.7′ (3.0m) Apart 13.5′ (4.1m) Apart
12′ Ceiling
13.7′ (4.2m) Apart 17.5′ (5.3m) Apart
14′ Ceiling
17.7′ (5.4m) Apart 21.5′ (6.6m) Apart
Figure 2: Speaker Spacing
4
GRILLE PAINTING
Before You Begin Sonance Professional Series In-Ceiling speaker grilles completely cover the exposed speaker frame, so only the grilles (not the speakers themselves) require painting. IMPORTANT: Mask the front flange of the speaker before painting the wall or ceiling (see Figure 3).
MASK ENTIRE FLANGE
Mask the Flanges of Installed Speakers Before
Painting the Ceiling Figure 3: Mask the Flanges of Installed Speakers
Before Painting the Ceiling
Carefully remove the scrim cloth from the underside of the grille. The scrim cloth is held in place with a light tacking glue. Use a heating agent such as a heat gun or hair dryer to soften the glue and carefully remove the cloth, since you will need to replace it when you’re done painting the grille. Be careful not to deform the cloth’s to properly replace the cloth on the grille. Remove any adhesive residue from the back of the grille before beginning painting.
Painting The Grilles
1. Prime the grille with a metal primer/bonder in a spray can. Carefully follow the manufacturer’s directions on the can.
2. We recommend using water-based latex paint on the grilles. Thin the paint with a proper thinning agent to a ratio of 1:1 paint-to-thinner, and strain it through a standard mesh strainer to remove any lumps.
3. Use a small touch-up gun or cap-spray gun with a #3 tip for painting.
A. Set the nozzle with a medium to wide fan. B. Set the pressure regulator to 60psi. C. Lightly spray the front of the grille in three
quick strokes from approximately 10″ away. D. Let the paint set for a minute, then turn the
grille 90º and lightly spray the grille again in three quick strokes. Repeat this step until all four sides of the grille have been evenly painted.
4. While the paint is still wet, inspect the grille and make sure that excess paint has not collected underneath the grille frame, and that none of the grille perforations are filled with paint. If any are, use compressed air to blow the paint out of the perforations.
IMPORTANT: If you find any grille perforations that are plugged with paint after the paint has dried, use a straight pin or sewing needle to carefully remove the paint.
5. Once the paint has thoroughly dried, replace the scrim cloth on the back of the grille and mount the grille on the speaker.
5
STANDARD INSTALLATION
STEP 1 Cut a hole in the drywall using the supplied cutout template (see Figure 4).
NOTE: For drop-ceiling instructions refer to page 7.
Figure 4: Cut-out Template
STEP 2 Connect the wires from your amplifier to the Euroblock connector (see Figure 5).
Pin 1 + Positive In Pin 2 – Negative In Pin 3 + Positive Out Pin 4 – Negative Out
IN
+
_
+OUT_
Figure 5: Euroblock Connector
Strip approximately .1875″ (5mm) of the insulation
opening on the connector. Use a small flat head screwdriver to tighten the corresponding screw to secure the wire (see Figure 6).
From Power Amplier
To Next Speaker
Figure 8: Loop Through Connection
NOTE: If square grilles are being used, the adapter frame must be installed at this time.
STEP 3 Once all the wires are terminated. Plug the black Euroblock connector into the back of the speaker (see Figure 9).
Figure 6: Secure the Wire
When using multiple speakers you can connect the speakers either in parallel or in the loop through method as shown (see Figure 7 and 8).
Figure 9
The included conduit clamp/wire strain relief can be installed on the side of the terminal cover. Once the clamp is installed, route the wires through the strain relief fitting. Tighten the screws on the clamp to secure the conduit/ wires the wires. Make sure not to over-tighten the screws and damage the wire.
CAUTION: Connections shall not be made with rigid conduit but with flexible conduit or wiring only.
From Power Amplier Figure 7: Parallel Connection
To Next Speaker
6
STEP 4 Make sure the Roto-Lock Clamps are in the full clockwise position so that all the clamps are tucked within the cutout border. Insert the speaker into the hole in the ceiling (see Figure 10).
Note: The maximum clamp thickness 2″ (50mm). To achieve maximum thickness, unscrew and reverse the foot of the Roto-Lock Clamps.
Note: For details on flex bracket go to www.sonance.com
DROP CEILING INSTALLATION
STEP 1B The included C-bracket and tile support rails should be used in all suspended ceiling installations. The C-bracket and tile support rails can also be used in installations when the speakers are mounted into material that will not support their weight. Insert the two tile support rails and C-bracket through the hole you have cut, placing them as shown. Using the two screws that are supplied,
(see Figure 13). After the C-bracket and tile support rails are installed, follow Step 2 through Step 7 in the standard installation instructions.
Figure 10: Insert Speaker into Hole
SAFETY PRECAUTION: Attaching the seismic tab to a support line is recommended for additional safety.
STEP 5
Roto-Lock Clamps will rotate into position automatically and begin clamping. When you notice resistance on the four screws, the speaker has been clamped successfully. The flange is designed to flex and conform to any small imperfections in the ceiling surface. Do not overtighten as this could damage the clamps.
STEP 6 At this step in the installation, the transformer tap selector can be set. Depending on your installation, you may wait to set the volume of each speaker until the system is completely installed (see Figure 11).
Figure 11
STEP 7 After the speaker is installed, and transformer tap adjustments are made, the grille can be installed. The grille is held in place by powerful magnets on the speaker frame. Place the grille against the speaker and the magnets will hold it firmly in place. When properly installed, the grille should make contact with the wall all the way around the speaker (see Figure 12).
Figure 12: Grille Installation
Figure 13: Screw C-Bracket to Tile
Support Rails
Figure 14: Insert Speaker into Hole and Secure Roto Lock Clamps
SAFETY PRECAUTION: Attaching the seismic tab to a support line is recommended for additional safety.
7
PS-C41RT SPECIFICATIONS
Frequency Range (-10dB) Frequency Range (-3dB) Power Capacity
Nominal Sensitivity Nominal Coverage Angle Directivity Factor (Q) Directivity (DI) Rated Maximum SPL Rated Impedance Transformer Taps Crossover Point Overall Dimension Cut Out Dimension Net Weight Shipping Weight Unit of Measure Grille LF Driver HF Driver Input Connectors Knockouts Safety Agency
Ceiling Thickness Range Suspension Points Back Enclosure
70Hz 25kHz 95Hz 20kHz 60 Watts Continuous Program Power 30 Watts Continuous Pink Noise 87dB 120 degrees conical coverage 7.6 8.1dB 102dB @ 1 meter (3.3 feet) average, 108dB peak 8 Ohms nominal 25W, 12.5W, 6.3W, and (3.2W @70V) 3000Hz 6.3″ x 6.5″ Deep (160mm x 165mm) 5.875″ Diameter (149mm) 3 lbs (1.36kg) Each 14 lbs (6.35kg) Pair 40165 Pair, 45165 Each Supplied with bezel-less white grille, black grille optional 4″ (100mm) Polypropylene Cone, Butyl Rubber Surround 0.75″ (19mm) Cloth Dome, Ferrofluid Cooled Four pin, Euroblock with loop output connections Side mounted 0.75″ (19mm) UL-1480A, UL-2043, CSA-C22.2 No.205, NFPA-70, NFPA-90A and EN54-24
0.125″ – 2″ (3mm – 50mm) One, on top surface Sealed, Polymer Composite UL94V-0
INCLUDED ACCESSORIES (PER SPEAKER)
(1) C-Ring (2) Tile Support Rails (1) Cutout Template (1) Euroblock Connector (1) White Grille
OPTIONAL ACCESSORIES
40152 Replacement Round Grille White x 1 Pair 40155 Round Grille Black x 1 Pair 40158 Square Adaptor w/ Grille White x 5 Pair 45158 Square Adaptor w/ Grille White x 1 Pair 40161 Square Adaptor w/ Grille Black x 5 Pair 45161 Square Adaptor w/ Grille Black x 1 Pair 92443 New Drywall Construction Flex Bracket x 5 Pair 40177 Metal Pre-construction Bracket x 6 Pair 40172 Tile Support Rails w/ C-Ring x 1 Pair 40175 Replacement RotoLock Toggle Feet x 1 Bag
8
PS-C61RT SPECIFICATIONS
Frequency Range (-10dB) Frequency Range (-3dB) Power Capacity
Nominal Sensitivity Nominal Coverage Angle Directivity Factor (Q) Directivity (DI) Rated Maximum SPL Rated Impedance Transformer Taps Crossover Point Overall Dimension Cut Out Dimension Net Weight Shipping Weight Unit of Measure Grille LF Driver HF Driver Input Connectors Knockouts Safety Agency Ceiling Thickness Range Suspension Points Back Enclosure
60Hz 25kHz 83Hz 20kHz 100 Watts Continuous Program Power 50 Watts Continuous Pink Noise 91 dB 120 degrees conical coverage 7.8 8.2dB 108dB @ 1 meter (3.3 feet) average, 116dB peak 8 Ohms nominal 32W, 16W, 8W, and (4W @ 70V) 2750Hz 9.13″ Diameter x 8.86″ Depth (232mm x 225mm) 8.25″ Diameter (210mm) 5 lbs (2.27kg) Each 19 lbs (8.61kg) Pair 40166 Pair, 45166 Each Supplied with bezel-less white grille, black grille optional 6.5″ (165mm) Polypropylene Cone, Butyl Rubber Surround 0.75″ (19mm) Cloth Dome, Ferrofluid Cooled Four pin, Euroblock with loop output connections Side mounted 0.75″ (19mm) UL-1480A, UL-2043, CSA-C22.2 No.205, NFPA-70, NFPA-90A and EN54-24 0.125″ – 2″ (3mm – 50mm) One, on top surface Sealed, Polymer Composite UL94V-0
INCLUDED ACCESSORIES (PER SPEAKER)
(1) C-Ring (2) Tile Support Rails (1) Cutout Template (1) Euroblock Connector (1) White Grille
OPTIONAL ACCESSORIES
40153 Replacement Round Grille White x 1 Pair 40156 Round Grille Black x 1 Pair 40158 Square Adaptor w/ Grille White x 5 Pair 45158 Square Adaptor w/ Grille White x 1 Pair 40162 Square Adaptor w/ Grille Black x 5 Pair 45162 Square Adaptor w/ Grille Black x 1 Pair 92337 New Drywall Construction Flex Bracket x 5 Pair 40126 Metal Pre-construction Bracket x 6 Pair 40173 Tile Support Rails w/ C-Ring x 1 Pair 40175 Replacement RotoLock Toggle Feet x 1 Bag
9
CERTIFICATIONS
SAFETY AGENCY COMPLIANCE Sonance Professional Series loudspeakers models PS-C41RT and PS-C61RT, meet the following standards:
UL-1480A: Speakers for Commercial and Professional Use UL-2043: Fire Test for Heat and Visible Smoke Release for Discrete Products and their Accessories Installed in Air Handling Spaces CSA-C22.2 No.205: Signal Equipment
Shall be installed in accordance with: NFPA-70: National Electric Code NFPA-90A: Installation of Air Conditioning and Ventilation CSA C22.1: Canadian Electrical Code
TECHNICAL ASSISTANCE AND SERVICE
The Technical Assistance Department at Sonance is available at (949) 492-7777 to answer any questions concerning the operation and installation of your speakers between the hours of 7:00 AM and 5:00 PM Pacific time, Monday through Friday, except holidays.
In the event your unit should need repair or service, you may return the unit to your authorized dealer or use the following guidelines:
PLEASE KEEP ORIGINAL PACKAGING WHEN POSSIBLE.
1. Be prepared to state the model number and / or serial number, date of purchase, and dealer’s name and address when calling.
2. Contact Sonance directly at (949) 492-7777 or at www.sonance.com. YOU MUST HAVE PRIOR AUTHORIZATION TO RETURN YOUR UNIT.
3. If you are returning the product directly to Sonance, call us to obtain a return authorization number (RMA) before shipping.
4. Ship the product via United Parcel Service, Federal Express, or other package delivery service. Please do not use the U.S. Postal Service.
5. Include the return authorization number on the shipping label. Please do not write the RMA number directly on the carton.
6. Ship to:
Attn: Quality Assurance Department RMA# (include RMA number here)
Sonance 11016 Mulberry Ave.
Suite B Fontana, CA 92337
10
LIMITED FIVE (5) YEAR WARRANTY
Sonance warrants to the first end-user purchaser that this Sonance-brand product (“Product”), when purchased from an authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated below. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent. EXCLUSIONS TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF, ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY SONANCE. ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and exclusive remedy and Sonance’s performance shall constitute full and final satisfaction of all obligations, liabilities and claims with respect to the Product. IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY OR OTHERWISE. This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied warranties is limited to period of Sonance’s express warranty. Your Product Model and Description: PS-C41RT / PS-C61RT. Warranty Period for this Product: Five (5) years from the date on the original sales receipt or invoice or other satisfactory proof of purchase. Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is nontransferable, applies only to the initial installation of the Product, does not include installation of any repaired or replaced Product, does not include damage to allied or associated equipment which may result for any reason from use with this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker, excessive heat, cold or humidity), or from service or repair which has not been authorized by Sonance. Obtaining Authorized Service: To qualify for the warranty, you must contact your authorized Sonance Dealer/Installer or call Sonance Customer Service at (949) 492-7777 within the warranty period, must obtain a return merchandise number (RMA), and must deliver the Product to Sonance shipping prepaid during the warranty period, together with the original sales receipt, or invoice or other satisfactory proof of purchase.
©2021 Sonance. All rights reserved. Sonance is a registered trademarks of Dana Innovations. Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product specification information visit our
website: www.sonance.com SONANCE · 991 Calle Amanecer · San Clemente, CA 92673 USA PHONE: (949) 492-7777 · FAX: (949) 361-5151 · Technical Support: (949) 492-7777 · www.sonance.com
336-0062 V2.21 11
Sonance
