Quick start guide
ACTIVE 20
Thank you for purchasing Waytraks Robotic Pool Cleaner.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies, long-lasting performance, and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.
Cautions & Warnings
- Use the originally supplied power supply only.
- Do not use an extension cable in any case
- Ensure the electrical outlet is protected by a ground fault interrupter (GA) or an earth leakage interrupter.
- Keep the power supply out of standing water.
- Do not enter the pool while the Pool Cleaner is
- Unplug the power supply before servicing.
- Do not use the cable to take the pool cleaner out of the water.
- Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm; pH 7.0 – 7.8; Temperature 6 -34°C (43-93°F); NaCI Maximum = 5000 ppm.
Digital Power Supply
Input:100-125 AC Volts 50-60 Hertz
120 Watt
Output: <30 VOC
IP 54
Specifications:
Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft
Helpful hints
- When working, the Power Supply should be placed in the shade.
- If the Dolphin is fitted with combined or wonder rushes, gently squeeze the brushes until they are soaked with water.
- Release minimal required floating cable length to ensure proper pool coverage. Leave excess cable rolled outside the pool.
- After each cleaning cycle washes the filters or cartridge. Clogged filters reduce scanning and cleaning efficiency.
- To remove the kinks stretch the cable out completely and let it sit for at least a day in the sun.
- Store the pool cleaner in a shady place on its Caddy, if not on a caddy, place the pool cleaner upside down.
Dolphin Power Supply
BASIC OPERATION
- Plug the Power supply into an electrical outlet.
- Press the ON button. The LEDs will turn on and the robot will start to operate. If no program is selected, the robot will perform a single cleaning cycle. The Power Supply will turn off automatically after 3 hours.
- You can program the power supply at any time. See the relevant section below for more details on each program.
*Bluetooth is not available for this model
WEEKLY TIMER
Your robot has a Weekly Timer feature that enables you to set an automatic cleaning schedule for the week ahead.
When the power supply is switched on, you can press the Weekly Timer button to select one of the following cleaning schedule options for the week ahead:
One-click – The robot will automatically work every day for a full cycle, that is, once a day for 7 days.
Two clicks – The robot will automatically work every alternate day for a full cycle, that is, 4 times a week.
C3 Three clicks – The robot will automatically work every 3 days, that is, 3 times in a week.
After selecting one of the above options, the robot will start to operate at the next occurrence of the programmed start time.
Note: A fourth click will cancel the cleaning schedule program (without a visible indication). If the robot is working in Weekly Timer mode, the Weekly Timer button constantly blinks between cycles. At the end of the week, the power supply automatically switches off and you need to reschedule the robot.
Robot operation
Set Up
Into the pool
Put the Pool Cleaner into the pool. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
Operation
Turn the power supply ON. The pool cleaner will now operate until it has reached the end of the cleaning cycle.
Out of the pool
Cleaning the filter
It is highly recommended to clean the filter basket after each cleaning cycle.
Note: Don’t let the filter cartridges dry out before cleaning.
Unplug the power supply before servicing
Open the latch to release the bottom lid in order to remove the debris.
Storage
Coil the cable and store it in a cool, dry place. Do NOT store the robot and its accessories where it will be exposed to direct sunlight, excessive heat, or frost.
Maintenance
Periodic filter cleaning
Cleaning the impeller
If you notice debris trapped in the impeller:
Unplug the power supply before servicing Clean the debris trapped in the impeller opening, according to the following steps:
99996203-USW
For online product warranty registration:
registration.maytronics.com
For a detailed manual (including videos):
manuals.maytronics.com/en/9999620B-USW
http://manuals.maytronics.com/99996203-USW
Documents / Resources
Maytronics 99996203-USW ACTIVE 20 Robotic Pool Cleaner [pdf] User Guide 99996203-USW, ACTIVE 20 Robotic Pool Cleaner |