Nomad System Felt

NOMAD SYSTEM FELT

Product Information

The Nomad System Felt is a modular wall assembly system designed
for easy installation and customization. It consists of felt
modules that can be assembled in both closed and open
configurations. Each box of Nomad System Felt contains either 5 sqf
[.46 sqm] in the closed assembly or 7 sqf [.65 sqm] in the open
configuration. The system also includes aluminum spacers for added
stability in open assemblies.

Product Usage Instructions

Closed Assembly:

1. Unpack the Nomad System by carefully cutting the tape to avoid
   damaging the modules.
2. Insert one module into the other along the central slot to
   create an X assembly. Repeat this step for all modules.
3. Arrange one row of X assemblies in the desired wall perimeter,
   leaving approximately one inch (2.5 cm) between X assemblies.
4. Insert subsequent rows of X assemblies into the bottom row
   using the long side slots (#1). Repeat this step to the desired
   height.

Open Assembly:

1. Follow steps 1-4 of the Closed Assembly instructions.
2. Insert subsequent rows of X assemblies into the bottom row
   using the short side slots (#2). Repeat this step to the desired
   height.
3. Insert aluminum spacers at the end of each open row to prevent
   sagging and improve stability.

Turning Corners:

1. Arrange two walls at a 90-degree corner and build them two
   modules high.
2. Connect the walls together using an X assembly.
3. Continue building the wall with another row of modules.
4. Add another X assembly to the opposing connection point. Repeat
   steps 2-4 to the desired height.

How to Clean:

Everyday Care

• Vacuum modules with a handheld attachment to avoid dust and
  dirt buildup, especially in high traffic area installations.
  Alternatively, lint, dirt, hair, or fuzz can be easily removed with
  a lint roller or tape.

Spot Cleaning

• Spot clean to eliminate small stains or dirt. Start by removing
  loose dirt with a vacuum. Wet a soft cloth with warm water and dab
  the stain. Repeat until the stain has been removed. Tougher stains
  can be removed using a small amount of delicate hand-washing
  detergent.

Washing Modules

• Soiled modules can be washed in a sink. Use warm water and
  clean by dabbing with a cloth or absorbent material. Remove excess
  moisture with a dry towel. Lay modules to dry on a flat surface
  with absorbent material below. Turn modules over periodically until
  they are completely dry. Do not scrub.

Disinfecting Modules

• Nomad System Felt can be cleaned with alcohol or a 1:10 bleach
  and water solution (approximately 5000 ppm) for high disinfection.
  For best results, leave the solution on the module surfaces for at
  least one minute. Clean after with a damp cloth using warm
  water.

NOMAD SYSTEM FELT

Parts List:

1

2

3

10 x Felt Modules
Closed Assembly:
4

Unpack the Nomad System by cutting tape carefully to avoid damaging modules.

Insert one module into the other along the central slot creating an X assembly shown. Repeat this step for all modules.

Arrange one row of X assemblies in the desired wall perimeter. Leave approximately one inch (2.5 cm) between X assemblies.

Insert subsequent rows of X assemblies into the bottom row. Use the long side slots (#1) for closed assemblies. Repeat this step to desired height.
Open Assembly:

4

5

Single box closed assembly

Finished! Use the selected slot throughout the entire assembly. Each box contains 5 sqf [.46 sqm] in the closed assembly.

Insert subsequent rows of X assemblies into the bottom row. Use the short side slots (#2) for open assemblies. Repeat this step to desired height.

Insert aluminum spacers at the end of each open row to prevent sagging and improve stability.

Finished! Use the selected slot throughout the entire assembly. Each box contains 7 sqf [.65 sqm] in the open configuration.

NOMAD SYSTEM FELT

Turning Corners:

1

2

Top View

Side View

3

4

Arrange two walls at a 90 degree corner and build them two modules high.
How to Clean:

Connect the walls together using an X assembly.

Continue building the wall with another row of modules.

Add another X assembly to the opposing connection point. Repeat steps 2-4 to desired height.

Everyday Care

Spot Cleaning

Washing Modules

Disinfecting Modules

Vacuum modules with a handheld attachment to avoid dust and dirt buildup, especially in high traffic area installations. Alternatively lint, dirt, hair, or fuzz can be easily removed with a lint roller or tape.

Spot clean to eliminate small stains or dirt. Start by removing loose dirt with a vacuum. Wet a soft cloth, with warm water, and dab the stain. Repeat until the stain has been removed. Tougher stains can be removed using a small amount of delicate hand-washing detergent.

Soiled modules can be washed in a sink. Use warm water and clean by dabbing with cloth or absorbent material. Remove excess moisture with a dry towel. Lay modules to dry on a flat surface with absorbent material below. Turn modules over periodically until they are completely dry. Do not scrub.

Nomad System Felt can be cleaned with alcohol or a 1:10 bleach and water solution (approximately 5000 ppm) for high disinfection. For best results leave the solution at least one minute on the module surfaces. Clean after with a damp cloth using warm water.

All trademarks, service marks and trade names (MIO, product names and the MIO logo) are owned and registered by MIO. All content including but not limited to text, designs, graphics, photos and all other content (“Content”) is a collective work under the United States and other copyright laws and is the proprietary property of MIO. All rights reserved. ©2021 MIOOIM LLC