TH17E0969 Children’s Electronic Motorcycle

CHILDREN’S ELECTRONIC MOTORCYCLE
· Suitable for 3+ Years · Maximum user weight: 30 kg
WARNING: Must be assembled by an adult.
OWNERS MANUAL
with Assembly Instructions
Read and understand this entire manual before using!
Please keep this manual for future reference as it contains important information. Before first time use, charge the battery for at least 4-6 hours, but no more than 10 hours.

About Your New Vehicle

1

On the purchase of your new Ride-On.
This ride-on car will provide your child with many miles of riding of enjoyment. To help assure you and your rider a safe ride we ask you to please read this manual carefully, and keep it for future reference.
Follow the recommendations in this manual, they are designed to improve the safety and operation of your ride-on car and its rider.

Specification
Battery 12V7AH X1 Charger 12V900mA input Depend on local voltage Motor 12V540-12000 Speed 4.2-6.4 km/h

Suitable age: Charge time: Load capacity: Size of car:

3+ Years 8-12 hours Under 30 kg 1065×515×680MM

BATTERY INFORMATION
Non-rechargeable batteries are not to be recharged. If removable rechargeable batteries are used, the are only to be charged under adult
supervision.
Remove rechargeable batteries from the product before charging. Do not mix old and new batteries. Do not mix different types of batteries: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
Insert batteries as indicated inside the battery compartment, anode to anode, cathode to cathode.
Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Battery leakage and corrosion can damage this product. Dispose of batteries safely.
Never short circuit the battery terminals.

Parts List
NO. PART NAME
1 Vehicle body 2 Front wheel 3 Front fork 4 Handle bar 5 Handle bar cover 6 Ø8 lock nut 7 Front axle 8 Ø8 washer 9 Charger 10 Ø4×12 screws 11 M8x150 bolt 12 Side wheel 13 Seat 14 Spanner 15 Ø10 washer

Q’TY (PCS)
1 1 1 1 2 8 1 3 1 6 1 2 1 2 2

2 REMARK

Assembly tools required (not included):

Screwdriver

Parts Diagram
13
15 6 12
14 9

3

65

10

4

10 11
5

15 6

6 12
1 8 6
7 68

3
68 2

Safety

4

PREVENT INJURIES AND DEATHS: · NEVER LEAVE CHILD UNATTENDED. ADULT DIRECT SUPERVISION IS REQUIRED. Always keep child
in view when child is in vehicle. · This toy should be used with caution since skill is required to avoid falls or collisions
causing injury to the user or third parties. · Protective equipment should be worn. · Never use in roadways, near cars, or on near steep inclines or steps, swimming pools or
other bodies of water. · Always wear shoes, always sit on the seat. · Not to be used in traffic. · This toy is unsuitable for children under 36 months due to its maximum speed; Maximum
user weight is 30 kg.
WARNING:
· CHOKING HAZARD! Not suitable for children under 36 months. · Must be assembled by an adult.
Rules for Safe Riding
· To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water, always wear shoes, and never allow more than 1 rider.
· Use the toy only on flat surfaces. Such as inside your house, garden or playground. · Never use in the dark. A child could encounter unexpected obstacles and have an accident.
Operate the vehicle only in the daytime or a well-lit area. · It is prohibited to change the circuit or add other electric parts · Inspect wires and connections of the vehicle periodically. · Do not let any child touch the wheels or be near them when the car is moving .

Attach the Rear Shock Absorber

5

1

2

3

Rear bottom View

1. Rotate the rear wheel frame until the bolt of the rear shock absorber is inserted into the hole on the rear wheel frame.
2. Turn the vehicle body on its side. Slide a Ø8 washer onto the front axle. 3. Tighten a lock nut to the end of the bolt with a spanner.

Attach the Side Wheels & Front Fender

6

1. Fit the side wheel to the vehicle body.

2. Slide a Ø10 washer onto the rear axle.

3. Tighten a lock nut to the end of the rear axle with a spanner.

Repeat for the other side.

4. Fit the front fender to the front fork.

2 3

5. Insert and tighten two Ø4×12 screws with a screwdriver.

1

5

4

Attach the Front Wheel

7

21
45
3
Remove the lock nuts and front axle from the front fork. 1-2. Slide a Ø8 washer to one end of the front axle. Tighten a lock nut to the end of the
front axle with a spanner. 3. Insert the front axle through the hole on one side of the front fork, then through the
hole in the center of the front wheel, and continue to push the front axle through the hole on the other side of the fork. 4. Slide a Ø8 washer to the front axle. 5. Use a spanner to tighten the lock nut into the front axle. Tip: Use two spanners to tighten the lock nuts on both sides of the front axle at the same time, but do not overtighten them, to ensure that the front wheel can rotate freely.

Attach the Handle bar – 1

8 1

2 3

Front bottom View

5

1. Fit the front fork assembly to the vehicle

body.

4

2. Align the holes on each side of front fork

with the holes on the vehicle body. Insert

the M8x150 bolt into the hole op top of

the front fork, through the holes on

vehicle body, and out through the hole on

the bottom of the front fender

3. Left up the front fork and tighten a locknut to the end of the M8x150 bolt with a spanner from the bottom side.

4. Fit the handle to the the front fork.

5. Tighten two lock nuts with a spanner to secure the handle bar to the front fork.

Attach the Handle bar – 2 2 1

9 3

5 6 4
1-2. Fit the handle bar cover to the front fork. Insert two Ø4×12 screws and tighten with a screwdriver. And repeat for other handel bar cover.
3. Pass the wire connector on the right handle bar through the cable tie on the front fork.
4. Plug the wire connector on the handlebar into the connector on the vechiel body. 5-6. Tighten the cable tie, then cut off the excess part of the cable tie with scissors.

Connect the Power Supply 2
Top View
3

10 1

1. Turn the lock on the top of the seat to unlock position with a coin or a slotted screwdriver.
2. Remove the seat. 3. Plug the red connector on the vehicle body into the red connector on the battery. 4. Replce the seat.

Use Your New Vehicle

11 2

1

5

3

4

1. Power button: Turn the product on and off. 2. Forward button: To move the product forward, press the button down.
To brake or slow down, release pressure from the button. 3. High speed button: Operate the product to move forward in high speed. 4. Low speed button: Operate the product to move forward in low speed. 5. Power Indicator Check the power level of your battery: All three lights means the battery is 100% (fully) charged. Two lights means the battery is 66% (mostly) charged. One light means the battery is 33% charged. We recommend recharging your battery
for 8-12 hours. No lights means the battery needs charging. Fully charge your battery for 8-12 hours.

Charging

12

WARNING!
ONLY AN ADULT CAN CHARGE AND RECHARGE THE BATTERY!

WARNING!
This product with Charging Protection: when charging, all functions will be cut off! Only an adult can charge and recharge the battery!
· The POWER SWITCH must be turned in OFF position when charging. · Before the first use, you should charge the battery for 4-6 hours. Do not recharge the
battery for more than 10 hours to avoid overheating the charger. · When the vehicle begins to run slowly, recharge the battery. · After each use or once a month minimum recharge time as 8 to 12 hours, less than 20
hours at most. · Use the only rechargeable battery and charger supplied with your vehicle. NEVER
substitute the battery or the charger with another brand. Using another battery or charger may cause a fire or explosion. – Only use the battery specified by the manufacturer – Only use the charger specified by the manufacturer. · Do not use the battery or charger for any other product.

1. Plug the charger port into the input socket. (above the right foot pedal) 2. Plug the charger plug into a wall outlet. The battery will begin charging.

Troubleshooting Guide

13

Problem Vehicle does not run

Possible Cause
Battery low on power

Solution
Recharge battery.

Vehicle does not run very long

Thermal fuse has tripped Battery connector or wires are loose
Battery is dead Electrical system is damaged

Reset fuse, see <Fuse> Check that the battery connectors are firmly plugged into each other. If wires are loose around the motor c. ontact your distributor please.
Replace battery, contact your distributor please.
Contact your distributor please.

Motor is damaged

Contact your distributor please.

Battery is under charged

Check that the battery connectors are firmly plugged into each other when recharging

Battery is old

Replace battery, contact your distributor please.

Vehicle runs sluggishly Battery low on power Battery is old Vehicle is overload

Recharge battery, contact your distributor please. Replace battery, contact your distributor please. Reduce weight on vehicle.

Vehicle is being used in harsh Avoid using vehicle in harsh conditions ,see <Safety>. conditions

Vehicle needs a push Poor contact of wires or

to go forward

Connectors

Check that the battery connectors are firmly plugged into each other. If wires are loose around the motor, contact your distributor please.

“Dead Spot” on motor

A dead spot means the electric power is not being delivered to the terminal connection and the vehicle needs repair. Contact your distributor please.

Difficult shifting from forward to reverse or vice-versa

Attempting to shift while the vehicle is motion

Completely stop the vehicle and shift, see <Use Your New Vehicle>

Loud grinding or clicking Motor or gears are damaged noises coming from motor or gear box

Contact your distributor please.

Battery will not recharge

Battery connector or adapter connector is loose

Check that the battery connectors are firmly plugged into each other.

Charger not plugged in

Charger feels warm when recharging

Charger is not working
This is normal and not a cause for concern

Check that the battery charger is plugged into a working wall outlet.
Contact your distributor please.

Completely read through this manual and the troubleshooting guide table before calling. If you still need help resolving the problem Contact your distributor please.

Maintaining

14

· It is parents’ responsibility to check main parts of the toy before using, must regularly examine for potential hazard, such as the battery, charge,cable or cord, plug, screws are fastening enclosure of other parts and that in the event of such damage, the toy must not be used until that damage had been properly removed.
· Make sure the plastic parts of the vehicle are not cracked or broken.
· Occasionally use a lightweight oil to lubricate moving parts such as wheels.
· Park the vehicle indoors or cover it with a tarp to protect it from wet weather.
· Keep the vehicle away from sources of heat, such as stoves and heaters. Plastic parts may melt.
· Recharge the battery after each use. Only an adult can handle the battery. Recharge the battery at least once a month when the vehicle Raider is not being used.
· Do not wash the vehicle with a hose. Do not wash the vehicle with soap and water. Do not drive the vehicle in rainy or snowy weather. Water will damage the motor, electric system and battery.
· Clean the vehicle with a soft, dry cloth. To restore shine to plastic parts, use a non-wax furniture polish. Do not use car wax. Do not use abrasive cleaners.
· Do not drive the vehicle in loose dirt, sand or fine gravel which could damage the moving parts, motors or the electric system.
· When not using, all the electrical source should be turn off. Turn off the power switch and disconnect the battery connection.

Fuse

15

The battery features a thermal fuse with a rest fuse that will automatically trip and cut all power to the vehicle if the motor, electric system or battery is overloaded. The fuse will reset and power will be restored after the unit is turned OFF for 20 seconds and then turned ON again. If the thermal fuse trips repeatedly during normal use, the vehicle may need repair. Contact your distributor please.

To avoid losing power, follow these guidelines: Do not overload the vehicle. Do not tow anything behind the vehicle. Do not drive up steep slopes. Do not drive into fixed objects, which may cause the wheels to spin, causing the motor to
overheat. Do not drive in very hot weather, components may overheat. Do not allow water or other liquids to come in contact with the battery or other electric
components. Do not tamper with the electric system. Doing so may create a short, causing the fuse to
trip.

Disposal Of Battery
Your sealed lead-acid battery must be recycled or disposed of in an environmentally sound manner.
Do not dispose of your lead-acid battery in a fire. The battery may explode or leak.
Do not dispose of a lead-acid battery in your regular, household trash. The incineration, land filling or mixing of sealed lead-acid batteries with household trash is prohibited by law.
Our products are suitable for ASTM F963; GB6675; EN71 and EN62115 standard.