Dyson V12 Detect Slim Cordless Vacuum
Cleaning your bin
Remove your bin
If it is necessary to clean your bin, empty it as shown in the ‘Emptying your bin’ section.
Press the red button located on the bin runner to release the bin and slide your bin off the runner.
Only clean your bin with a damp cloth.
Make sure that the bin and seals are completely dry before replacing.
Refit your bin
Insert the spine on to the bin runner.
Close your bin by pushing the bin base upwards until the bin and bin base click into place.
Your bin isn’t dishwasher safe and the use of detergents, polishes or air fresheners to clean your bin isn’t recommended, as it may damage your machine.
Clearing blockages
Disconnect your machine from the charger before looking for blockages.
Be careful not to touch the trigger and be aware of sharp objects.
Leave your machine to cool down before looking for blockages.
Don’t use your machine when looking for blockages as this could cause injury.
Remove the bin and check for blockages in the main body of your machine.
Make sure any blockages are completely cleared and all parts are fitted before using your machine.
If your machine detects a blockage, the motor will pulse and you won’t be able to use your machine until the blockage has been cleared.
If you try to use your machine when the motor is pulsing, it will automatically cut out.
To check for blockages in the main body of the machine, remove the bin following the instructions in the Cleaning your bin section and remove the blockage.
If you cannot clear an obstruction, you may need to remove the brush bars.
Refit all parts securely before using your machine.
Clearing blockages isn’t covered by your guarantee.
Washing your filter
Wash your filter at least once a month to maintain optimum suction power.
For more information and support for your machine go online: www.dyson.com/support
Important: your filter must be completely dry before you put it back into the
machine. Your machine could be damaged if used with a damp filter.
Twist off your filter
Twist your filter anti-clockwise and pull it away from your machine.
Tap your filter
Before washing your filter, tap it gently over a bin to remove any loose dust and debris.
Wash your filter
Wash with warm, running tap water – gently rubbing your filter with your fingto remove the dirt.
Fill and shake
Place your hand over one end of your filter.
Fill the filter with warm tap water.
Place your hand over the open end of the filter and shake it firmly to remove trapped dirt and debris.
Repeat these steps until the water runs clear.
Shake out the water
Empty the filter and shake firmly to remove excess water.
Shake with the filter in both an upward and downward position.
Keep shaking until there’s no water coming from the filter.
Dry your filter
Leave your filter to dry for at least 24 hours in a well-ventilated, warm place.
Don’t dry your filter in a tumble dryer, microwave or near a naked flame.
Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.
Washing your Laser Slim Fluffy™ brush bar
Your Laser Slim Fluffy™ cleaner head has a washable brush bar. To maintain optimum performance, check and wash your brush bar regularly.
Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Remove your brush bar
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Press the cleaner head release button on the end of the wand. Place the cleaner head upside down.
Push the end cap up fully and pull the brush bar out of the cleaner head.
Wash and dry your brush bar
Hold your brush bar under running water and gently rub to remove any lint or dirt.
Stand your brush bar upright as shown. Leave to dry completely for at least 24 hours.
Replace your brush bar
Before replacing, check that your brush bar is completely dry.
Reattach the end cap to your brush bar.
Slide your brush bar into the cleaner head. Push the end cap back down to the closed position.
Cleaning your laser lens
To maintain optimum performance, keep your laser lens clean. Only clean
the lens when the cleaner head is not attached to your machine.
Use a soft, dry, lint-free cloth to wipe the lens.
Cleaning your tools
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Wipe with a damp, lint-free cloth, without touching the connector end.
Make sure your tools are completely dry before using.
Combination tool | |
Crevice tool | |
Soft dusting brush | |
Stubborn dirt brush |
Clearing blockages from your
Hair screw tool
Your Hair screw tool doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Remove the cover and brush bar
Remove the Hair screw tool from the wand or machine.
Push the base plate open. Press the red lever down to release the cleaner headcover.
Pull the cleaner headcover off the main body of the tool.
Look for obstructions
Pull your brush bar firmly to remove it from the main body.
Check and remove any obstructions from all three parts of your Hair screw tool.
Your Hair screw tool isn’t washable. Wipe over with a damp lint-free cloth.
Don’t put any part of your machine in a dishwasher or use detergents, polishes, or air fresheners.
Reassemble Hair screw tool
Looking after your machine
To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.
- Look after your machine
If your machine is dusty, wipe with a damp lint-free cloth.
Check for blockages in the cleaner head, tools, and main body of your machine.
Wash your filter regularly and leave it to dry completely.
Don’t use detergents or polishes to clean your machine. - Look after your battery
To get the best performance and life from your battery, use Eco or Auto/Med mode.
Your machine won’t operate or charge if the ambient temperature is below 5°C(41°F). - This is designed to protect both the motor and battery.
Your serial numbers
You can find your serial numbers on your machine, battery, and charger.
Use your serial number to register.
For more information and support for your machine go online: www.dyson.com/support
FAQS
We have platform beds and it’s a bit difficult to vacuum under. All in all though, I love this vacuum cleaner! It is super light and convenient to use.
yes
No. One button press to turn it on then another to turn it off.
A hard floor, carpet and pet vac attachment as well as two small attachments on the base.
You can buy spare batteries. However, they don’t just pop out like battery power tools.
The battery in this is fixed and screwed in. You’d need to unscrew it every time you changed the battery.
It comes with many but not all of the Dyson attachments. Please consult the Amazon page for this model, as it will show you which ones it includes. It’s a great little machine!
Not certain of the actual weight but it’s very light in weight and yet very heavy duty for performance! I’d estimate the weight to be around 8-10 lbs.
We have platform beds and it’s a bit difficult to vacuum under. All in all though, I love this vacuum cleaner! It is super light and convenient to use.
The unit will run at a consistent power level or variable power level if running by the dirt sense or as you decide by the power selection throughout the battery charge. It will maintain.
No problem at all.
yes so far
You can have one battery charging while using another since the batteries are removable. One battery plugged the charging station or just plugged straight in (since you don’t have to use a charging station) while the other is in use. When one runs out, swap them.
Yes it does, you can mount the charger base to the wall or just use the charger by itself and plug it in
VIDEO
Documents / Resources
dyson V12 Detect Slim [pdf] User Manual V12 Detect Slim | |
dyson v12 Detect Slim [pdf] User Manual v12 Detect Slim, v12, v12 Slim, Detect Slim, Slim |