Rowley Rtmdchcbp High Capacity Battery Pack Owner's Manual (+ PDF)

Contents hide

1 RTMDCHCBP High Capacity Battery Pack

2 Product Information

3 Product Usage Instructions

3.1 Safety Instructions

3.2 Specifications

3.3 Installation

3.3.1 Charging

3.3.2 Attachment Methods

3.4 Motor Connections

3.5 Documents / Resources

3.5.1 References

RTMDCHCBP High Capacity Battery Pack

Product Information

The High Capacity Battery Pack (model RTMDCHCBP) is a
rechargeable Li-ion battery pack designed for use with DC Tubular
Motors. It allows the motors to operate wirelessly without the need
for traditional battery wands with disposable batteries. The
battery pack has a small profile, making it easy to place in the
window pocket. It can be fully recharged in approximately 6 hours
and can be paired with the optional Solar Panel Battery Charger for
continuous recharging.

The battery pack has the following features:

Up to 500 Up/Down Cycles on a Single Charge
Small Profile
Recharges in 6 hours
Optional Solar Panel for Continuous Recharging

Product Usage Instructions

Safety Instructions

Before installation, please read and follow these important
safety instructions:

Incorrect installation can lead to serious injury and will void
the manufacturer’s liability and warranty.
This product should not be used by children or individuals who
are unable to operate it.
Do not dispose of the battery pack in general waste. Please
recycle batteries and damaged electrical products
appropriately.

Specifications

Input Volts: 12.6V
Output Volts: 12.0V
Capacity: 2600mAh
Insulation Class: III
Battery Size/Type: 1-1/4 x 1-1/4 x 10 / Lithium-ion
Rechargeable
Temperature Working Range: Not specified

Installation

Charging

Before first use, the Rechargeable Battery Pack must be fully
charged to prolong battery lifespan. Follow these steps to charge
the battery pack:

Connect the High Capacity Battery Pack to the Battery Charger
using the provided 2 pin locking SMR style connector. The charger
model is RPTMDC-CHARGE.
Charge the battery pack for 6 hours.
Install the battery pack as required. Refer to Section 1.2 for
attachment methods.

Attachment Methods

The Rechargeable Battery Pack can be attached using the
following methods:

Hook
Screw
Charging Cable (model RTMDC18/25)
Double Sided Tape (not supplied)

Important: Do not install the Rechargeable Battery Pack where it
will be exposed to direct sunlight.

Motor Connections

The battery pack uses a 2 pin, non-locking JST style connector
for motor connections. The compatible motors are:

Tilt Blinds: MTDCRF-TILT-1
Tubular Motors: MTDCRF18-0.2, MTDCRF25-1.1, MTDCRFQ28-2
Cord Lift: RTMDCZ25, RTMDCZ28, MT01-1225-069002,
MT01-1228-069002

If you have any questions or need further assistance, please
contact our customer support.

View Fullscreen

High Capacity Battery Pack RTMDCHCBP
High Capacity Battery Pack – The rechargeable Li-ion Battery Pack enables DC Tubular Motors to operate wirelessly and without the constraints of traditional battery
wands with disposable batteries.
The small profile allows for optimal placement in the window pocket, fully recharges in about 6 hours and can be paired with the optional
Solar Panel Battery Charger for continuous recharging.

FEATURES

500
Up to 500 Up / Down Cycles on Single Charge

Small Profile

123456

Battery Health Status in R-TEC Automation® App

Recharges in 6 hours

Optional Solar Panel for Continuous
Recharging

SAFETY INSTRUCTIONS
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

CAUTION
· Do not expose to moisture or extreme temperatures. · Do not allow children to play with this device. · Use or modification outside the scope of this instruction manual will void warranty. · Installation to be performed by a suitably qualified installer. · For use with DC powered Cord Lift, Tilt and tubular motors. · Ensure correct crown and drive adaptors are used for the intended system. · Use only Rollease Acmeda hardware. · Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation. · Do not expose the battery to water or install in humid or damp environments. · Do not drill into battery body. · The routing of cable through walls shall be protected by isolating bushings or grommets. · Ensure cables are clear and protected from moving parts. · Do not use if any cables are damaged
Important safety instructions to be read prior to operation.
· It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. · Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
should not be allowed to use this product.
· Keep battery away from acid, alkali, heat & fire.

Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately.

5005833

SPECIFICATIONS

Input Volts

12.6V

Output Volts

12.0V

Capacity

2600mAh

Insulation Class

III

Battery Size/Type

1-1/4″ x 1-1/4″ x 10″ / Lithium-ion Rechargable

Temperature Working Range

32°F to 140°F (0°C to 60°C)

1 INSTALLATION
1.1 Charging
Charging uses the 2 pin locking “SMR” style connector.

IMPORTANT
Rechargeable Battery Pack must be fully charged prior to first use to prolong battery lifespan.
Step 1. CCoonnnneect the HReigchhaCragpeaacbiltey Battery Pack
ttoo tthhee BRaotlltearyseChAacrmgerd.a charger. RPTaMrtD#C: 1M8T/D2C5B-CHARGE
Step 2. Charge for 6 hours.

Step 3. Install as required.
See Section 1.2 Attachment Methods

1.2 Attachment Methods

Hook

Screw

Charging Cable
RTMDC18/25
Double Sided Tape*

*Not supplied

IMPORTANT
Do not install Rechargeable Battery Pack where it will be exposed to direct sun light.

1.3 Motor Connections

Charging uses the 2 pin, non-locking “JST” style connector.

Tilt Blinds
MTDCRF-TILT-1

Tubular Motors
MTDCRF18-0.2

MTDCRF25-1.1