Lnc Modern Vanity Light Instruction Manual (+ PDF)

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may
need it at a later time.
Before you start, NEVER attempt any work without shutting off
the electricity until the work is done.

Installation:

Go to the main fuse or circuit breaker box in your home and
place the main power switch in the OFF position.
Place the wall switch in the OFF position.
Ensure the mounting surface is clean, dry, flat, strong enough,
and 1/4 larger than the canopy on all sides.
If there are any gaps exceeding 3/16 between the mounting
surface and canopy, correct them as required.
Verify that the ceiling or wall can withstand the weight of the
lamp before installation.
Make sure the voltage you are using is 120V and the maximum
wattage is 40W per bulb.
Keep the lamp away from acidic and alkaline substances to
prevent damage to the lamp surface.
When replacing bulbs, turn off or unplug the lamp and wait
until it is cool as bulbs can get hot quickly.
Follow common sense, caution, and care when using any
electrical products.

Assembly and Installation:

Unscrew knob nuts (F) from back plate (E) and set them aside
for later installation.
Carefully pass the supply wires from the outlet box through
mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting
screws (A).
Make wire connections according to the provided wire connection
chart. Note: Never connect other wires to ground wires.
Twist wires together with plastic wire connectors until tightly
joined and wrap each connector with approved electrical tape.
Ensure no wire strands are exposed and carefully tuck all wires
into the outlet box.
Unscrew socket rings (K) from sockets (I) and fix glass shades
(J) to sockets (I) with socket rings (K).
Install bulbs (not included) without exceeding the maximum
recommended wattage on the socket.
Adjust swivel joints (H) and sockets (I) to the appropriate
direction as shown in the illustration. Note: Only adjust the
vertical direction of sockets (I) component to prevent glass
breakage or injury.
Check that everything is installed properly before turning on
the light.

Cleaning:

To clean the fixture, wipe it with a soft cloth. Clean glass
with a mild cleaner (such as mild and nonabrasive soap). Do not use
abrasive materials such as scouring pads or powders, steel wool, or
abrasive paper.

Ordering Parts:

Keep this sheet for future reference in case you need to order
replacement parts. All parts for this fixture can be ordered from
the place of purchase. Be sure to use the exact wording from the
illustration when ordering parts.

View Fullscreen

[email protected]
Item Number: A04302 WARNING (To reduce the risk of fire, electric shock, or personal injury): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. 4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides.
Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required. 5. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs
get hot quickly. 9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may
occur. It must be understood that common sense, caution and care must be used with any electrical products. IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture
Page: 1 / 4

[email protected]
PARTS INCLUDING: (C) Green ground screw (1) (D) Mounting plate (1) (E) Back plate (1) (F) Knob nut (2) (G) Arm (1) (H) Swivel joint (2) (I) Socket (2) (J) Glass shade (2) (K) Socket ring (2) ACCESSORIES ENCLOSED: A) Mounting screw (2) B) Plastic wire connector (3) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration. 2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B) Place the wall switch in the “OFF” position. 3. Make assembly
Step A1: Unscrew knob nuts (F) from back plate (E), then set them aside for later installation. Step A2: Carefully pass the supply wires from the outlet box through mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A). Step A3: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Page: 2 / 4

Connect ground wires according to the below chart chart

[email protected] Connect wires according to the below

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in back plate (E) with the preassembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug. NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of preassembled mounting screws on mounting plate assembly (D) by unscrewing the preassembled hex nuts and then screwing the preassembled mounting screws in or out of mounting plate (D) until the secure length is achieved. Tighten the preassembled hex nuts and back to Step A4.
Step A5: 1) Unscrew socket rings (K) from sockets (I). Fix glass shades (J) to sockets (I) with socket rings (K). 2) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
You can adjust swivel joints (H) and sockets (I) to the appropriate direction as shown in the illustration.
Note: Adjust the vertical direction of sockets (I) component, but not glass shades (J), to prevent the glass from breaking and scratching hands.
4. Check everything is installed properly, then you could turn on the light. Enjoy!
CLEANING To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. ORDERING PARTS
Page: 3 / 4

[email protected]
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
Page: 4 / 4