Smarteh Lbt-1.do1 Bluetooth Mesh Relay Output Module User Manual (+ PDF)

Standards, recommendations, regulations, and provisions of the
country in which the devices will operate must be considered while
planning and setting up electrical devices. Work on 100 .. 240 V AC
network is allowed for authorized personnel only.

Danger Warnings

Devices or modules must be protected from moisture, dirt, and
damage during transport, storing, and operation. If the device is
used in a manner not specified by the manufacturer, the degree of
protection provided by the equipment may be impaired. Waste
electrical and electronic equipment (WEEE) must be collected
separately!

Manufacturer Information

Manufacturer: SMARTEH d.o.o.

Address: Poljubinj 114, 5220 Tolmin, Slovenia

Product Usage Instructions

Operation Requirements

The LBT-1.DO1 Bluetooth Mesh Relay output module can only
operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway
while provisioned to the same Bluetooth Mesh network.

Device Connection

Refer to the following diagram for device connection:

Bluetooth Mesh System Topology

Refer to the following diagram for Bluetooth Mesh system
topology:

Other Relay Output Module Functions

Refer to the user manual for information on other relay output
module functions.

Operation Parameters

Refer to the following table for operation parameters:

Reg. Name	Description	Raw Engineering Data
10	Execute command	Execute command for Read and/or Write by toggling bit
11	Destination address*	Destination node address. Can be a unicast, group, or virtual address
12	Element index*	Sending node model element index
13	Vendor ID*	Vendor ID of the sending node model
14	Model ID*	Model ID of the sending node model
16	Virtual address index*	Index of the destination Label UUID
17	Application key index*	The application key index used
18	Option code**	Refer to the option code table

Note: *Values range from 0 to 65535

Note: **Refer to the option code table for available options

View Fullscreen

USER MANUAL
Longo Bluetooth Products LBT-1.DO1 Bluetooth Mesh Relay output module
Version 2
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: +386(0)5 388 44 00 / e-mail: [email protected] / www.smarteh.si

Longo Bluetooth Products LBT-1.DO1
Written by SMARTEH d.o.o. Copyright © 2023, SMARTEH d.o.o. User Manual Document Version: 2 May 2023
i

Longo Bluetooth Products LBT-1.DO1
STANDARDS AND PROVISIONS: Standards, recommendations, regulations and provisions of the country in which the devices will operate, must be considered while planning and setting up electrical devices. Work on 100 .. 240 V AC network is allowed for authorized personnel only.
DANGER WARNINGS: Devices or modules must be protected from moisture, dirt and damage during transport, storing and operation.
WARRANTY CONDITIONS: For all modules LBT-1 if no modifications are performed upon and are correctly connected by authorized personnel in consideration of maximum allowed connecting power, warranty of 24 months is valid from the date of sale to the end buyer, but not more than 36 months after delivery from Smarteh. In case of claims within warranty time, which are based on material malfunctions the producer offers free replacement. The method of return of malfunctioned module, together with description, can be arranged with our authorized representative. Warranty does not include damage due to transport or because of unconsidered corresponding regulations of the country, where the module is installed. This device must be connected properly by the provided connection scheme in this manual. Misconnections may result in device damage, fire or personal injury. Hazardous voltage in the device can cause electric shock and may result in personal injury or death. NEVER SERVICE THIS PRODUCT YOURSELF! This device must not be installed in the systems critical for life (e.g. medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer, the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected separately!
LBT-1 devices are developed considering the following standards: · EMC: EN 303 446-1 · LVD: EN 60669-2-1
Smarteh d.o.o. operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice.
MANUFACTURER: SMARTEH d.o.o. Poljubinj 114 5220 Tolmin Slovenia
ii

Longo Bluetooth Products LBT-1.DO1
Longo Bluetooth Products LBT-1.DO1
1.ABBREVIATIONS…………………………………………………………………….1 2.DESCRIPTION……………………………………………………………………….2 3.FEATURES…………………………………………………………………………..3 4.OPERATION…………………………………………………………………………4
4.1.Other relay output module functions……………………………………….5 4.2.Operation parameters……………………………………………………….6 5.INSTALLATION………………………………………………………………………9 5.1.Connection scheme………………………………………………………….9 5.2.Mounting instructions………………………………………………………11 6.SYSTEM OPERATION ………………………………………………………………15 6.1.Interference warning ………………………………………………………15 7.TECHNICAL SPECIFICATIONS………………………………………………………16 8.MODULE LABELING………………………………………………………………..17 9.CHANGES …………………………………………………………………………18 10.NOTES……………………………………………………………………………19
iii

Longo Bluetooth Products LBT-1.DO1

1. ABBREVIATIONS

LED PLC PC OpCode

Light Emitted Diode Programmable Logic Controller Personal Computer Message Option Code

Longo Bluetooth Products LBT-1.DO1
2. DESCRIPTION
LBT-1.DO1 Bluetooth Mesh relay output module is designed to be used as a relay digital output module with RMS current and voltage measuring possibility. The module can operate with a wide range of DC and AC voltages. It can be placed inside the 60mm diameter flush mounting box and so it can be used for switching On and Off the power supply voltage of standard electric wall sockets. It also can be placed inside the lights, inside various electrical equipment and devices to switch On and Off their power supply voltage. Additional switch input is provided to have the possibility of manually switching On and Off the module relay. LBT-1.DO1 Bluetooth Mesh relay output module can also be connected close to the light in the traditional electrical wiring 115/230 VAC for lightning. Light connected to the LBT-1.DO1 relay can be switched on and off with existing light switches. The module can detect power supply input voltage drop when the switch is pressed. Wire bridge on the last switch before the LBT-1.DO1 relay module should be wired as shown in Figure 4. While LBT-1.DO1 is a Bluetooth Mesh module the relay output can be also switched On and Off by using Bluetooth Mesh communication. At the same time relay RMS current and voltage can be sent over the Bluetooth Mesh communication. LBT-1.DO1 Bluetooth Mesh relay output module can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway connected to the same Bluetooth Mesh network. LBT-1.GWx Modbus RTU gateway is connected to the main control device as Smarteh LPC-3.GOT.012 7″ PLC based Touch panel, any other PLC or any PC with Modbus RTU communication. Besides Smarteh Bluetooth Mesh devices, other standard Bluetooth Mesh devices can be integrated into above mentioned Bluetooth Mesh network. More than a hundred Bluetooth Mesh devices can be provisioned and can operate in a single Bluetooth Mesh network.
2

Longo Bluetooth Products LBT-1.DO1
3. FEATURES
Figure 1: LBT-1.DO1
Table 1: Technical data
Communication standard: Bluetooth Mesh is a low power wireless mesh protocol and allows device to device communication and device to main control device communication. Radio frequency: 2.4 GHz Radio range for direct connection: < 30m, depending on application and building. By using Bluetooth Mesh topology, much bigger distances can be achieved. Power supply: 11.5 .. 13.5 V DC or 90 .. 264 V AC, 50/60Hz Ambient temperature: 0 .. 40 °C Storage temperature: -20 .. 60 °C Status indicators: red and green LED Relay output with maximum resistive load current 4 A AC/DC RMS current and voltage measurement, power consumption measurement Power supply line switch digital input, operating with 90 .. 264 V AC power supply voltage Switch digital input Mounting in flush mounting box
3

Longo Bluetooth Products LBT-1.DO1
4. OPERATION
LBT-1.DO1 Bluetooth Mesh Relay output module can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway while provisioned to the same Bluetooth Mesh network.
Figure 2: LBT-1.DO1 device connection
Figure 3: Bluetooth Mesh system topology 4

Longo Bluetooth Products LBT-1.DO1
4.1. Other relay output module functions
· Factory reset: This function will delete all Bluetooth Mesh network parameters stored on LBT-1.DO1 relay output module and will restore to the conditions of the initial programming, ready for provisioning. See Table 5 for more information.
5

Longo Bluetooth Products LBT-1.DO1

4.2. Operation parameters
LBT-1.DO1 Bluetooth Mesh Relay output module accepts a set of operation codes as specified in below tables 2 to 4. LBT-1.DO1 Bluetooth Mesh relay output module is communicating with the main control device as Smarteh LPC-3.GOT.012 or similar via Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway. All communication between the main control device is performed by using Modbus RTU communication. Individual Bluetooth Mesh node configuration data should be observed by using the network provisioning tool.

Table 2: 4xxxx, Holding registers, Modbus RTU to Bluetooth Mesh gateway

Reg. Name

Description

Raw Engineering data

10 Execute command

Execute command for Read and/or Write by toggling bit

Bit0 toggle Write Bit1 toggle Read

11 Destination address*

Destination node address. Can be a unicast, group or virtual address

0 .. 65535 0 .. 65535

12 Element index*

Sending node model element index

0 .. 65535 0 .. 65535

13 Vendor ID*

Vendor ID of the sending node model

0 .. 65535 0 .. 65535

14 Model ID*

Model ID of the sending node model

0 .. 65535 0 .. 65535

16 Virtual address index*

Index of the destination Label UUID

0 .. 65535 0 .. 65535

17 Application key index*

The application key index used

0 .. 65535 0 .. 65535

18 Option code**

Refer to the option code table

0 .. 63 0 .. 63

19 Payload byte length** 20 Payload word[0]**

Refer to the option code table Refer to the option code table

1 .. 10 1 .. 10 bytes 0 .. 65535 0 .. 65535

21 Payload word[1]**

Refer to the option code table

0 .. 65535 0 .. 65535

22 Payload word[2]**

Refer to the option code table

0 .. 65535 0 .. 65535

23 Payload word[3]** 24 Payload word[4]**

Refer to the option code table Refer to the option code table

0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535

* Observed from network provisioning tool ** User defined parameters, refer to the option code table

Longo Bluetooth Products LBT-1.DO1

Table 3: 3xxxx, Input registers, Modbus RTU to Bluetooth Mesh gateway

Reg. Name

Description

Raw Engineering data

10 Messages pending

Number of messages pending in receiving buffer

1 .. 10 1 .. 10

11 Destination address

Destination node address. Can be a unicast, group or virtual address

0 .. 65535 0 .. 65535

12 Element index

Sending node model element index

0 .. 65535 0 .. 65535

13 Vendor ID

Vendor ID of the sending node model

0 .. 65535 0 .. 65535

14 Model ID

Model ID of the sending node model

0 .. 65535 0 .. 65535

15 Source address

Unicast address of the node model which sent the message

0 .. 65535 0 .. 65535

16 Virtual address index

Index of the destination Label UUID

0 .. 65535 0 .. 65535

17 Application key index 18 Option code 19 Payload length 20 Payload word[0] 21 Payload word[1] 22 Payload word[2] 23 Payload word[3] 24 Payload word[4]

The application key index used Refer to the option code table Refer to the option code table Refer to the option code table Refer to the option code table Refer to the option code table Refer to the option code table Refer to the option code table

0 .. 65535 0 .. 65535 0 .. 63 0 .. 63 1 .. 10 1 .. 10 bytes 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535 0 .. 65535

Table 4: Relay output LBT-1.DO1 option codes

Option code

Name

Description

FW version status

Firmware version status

Operation mode set

Node operation mode selection

Raw Engineering data
0 .. 65535 0 .. 65535
0 Not used 1 Not used 2 Not used 3 Not used 4 Reset 5 Factory reset

Longo Bluetooth Products LBT-1.DO1

Table 4: Relay output LBT-1.DO1 option codes

Wake up interval command

Command to set the time interval in which the device wakes up and sends data about the current and voltage status

Status of the time interval in

Wake up interval status

which the device wakes up and sends data about the

current and voltage status

Voltage status

Input voltage RMS value

Current status

Load current RMS value

Digital out command Relay output command

Digital out status

Relay output status

PS line switch enable command

Command for enabling the power supply line switch input

PS line switch enable status

Enable status of the power supply line switch input

Switch SW enable command

Command for enabling the SW switch input

Switch SW enable status

Enable status of the SW switch input

0 .. 65535 0 .. 65535 s
0 .. 65535 0 .. 65535 s
0 .. 65535 0 .. 6553.5 V 0 .. 65535 0 .. 65.535 A 0 OFF 1 ON 0 OFF 1 ON 0 Disable 1 Enable 0 Disabled 1 Enabled 0 Disable 1 Enable 0 Disabled 1 Enabled

Longo Bluetooth Products LBT-1.DO1
5. INSTALLATION
5.1. Connection scheme
Figure 4: Example of connection scheme
9

Longo Bluetooth Products LBT-1.DO1
Figure 5: LBT-1.DO1 module

Table 5: Inputs, Outputs and LEDs

K1.1

Load output: neutral or negative

K1.2

Power supply input: neutral or negative (-)

K1.3

Switch input: line, 90 .. 264 V AC, 11.5 .. 30 V DC

K1.4

Load output: line or positive

K1.5

Power supply input: line or positive (+), 90 .. 264 V AC or 11.5 .. 30 V DC

LED1: red

Error

2x blink inside 5 s time period = network/friend lost 3x blink inside 5 s time period = unprovisioned node

LED2: green Status

1x blink = normal operation. It’s also feedback for S1 reed contact, when activated with magnet.

Reed contact

Mode setting contact

Inside 5 s time window, perform corresponding number of

swipes in duration of not less than 200 ms with permanent

magnet close to the window sensor S1 reed contact position.

Following window sensor action or mode will be set:

Number of swipes

Action

________________________________

Reset

Factory reset

A hardware reset is triggered if reed contact is continuously closed with a permanent magnet for more than 5 seconds.

Longo Bluetooth Products LBT-1.DO1
5.2. Mounting instructions
Figure 6: Housing dimensions
Dimensions in millimeters.
11

Longo Bluetooth Products LBT-1.DO1
Figure 7: Mounting in flush mounting box
12

Longo Bluetooth Products LBT-1.DO1
Figure 8: Installation flowchart 13

Longo Bluetooth Products LBT-1.DO1
1. Switching Off the main power supply. 2. When you mount the module inside the flush mounting box first check, that the flush
mounting box is depth enough. If needed please use an additional spacer between the flush mounting box and the socket or contact the producer for additional information. 3. Mount the module up to the provided place and wire the module according to the connection scheme in Figure 4. When you connect the module to the traditional electrical wiring for lighting please be sure, that you wired the bridge on the last switch before the LBT-1.DO5 module as shown in Figure 4. 4. Switching On the main power supply. 5. After a few seconds Green or Red LED starts to blink, please see the flowchart above for details. 6. If the module is not provisioned Red LED will blink 3x, the provisioning procedure has to be started. Contact the producer for more details*. 7. Once provisioning is finished, the module will continue with the normal mode of operation and this will be indicated as Green LED blinking once per 10 seconds. Dismount in reverse order. *NOTE: Smarteh Bluetooth Mesh products are added and connected to a Bluetooth Mesh network by using standard provisioning and configuration mobile apps tool such as nRF Mesh or similar. Please contact producer for more detail information.
14

Longo Bluetooth Products LBT-1.DO1
6.SYSTEM OPERATION
LBT-1.DO1 Bluetooth Mesh relay output module can switch power to the output load based on power suplly voltage drop pulse, based on switch input voltage change or based on Bluetooth Mash command.
6.1. Interference warning
Common sources of unwanted interference are devices that generate high frequency signals. These are typically computers, audio and video systems, electronic transformers, power supplies and various ballasts. The distance of the LBT-1.DO1 relay output module to the above mentioned devices should be at least 0.5 m or greater. WARNING:
· In order to protect plants, systems, machines and network against cyber threats it is necessary to implement and continuously maintain up to date security concepts.
· You are responsible for preventing unauthorized access to your plants, systems, machines and networks and they are allowed to be connected to the Internet only, when security measures like firewalls, network segmentation, etc. are in place.
· We strongly recommend the updates and usage of the latest version. Usage of the version that is no longer supported may increase the possibility of cyber threats.
15

Longo Bluetooth Products LBT-1.DO1

7.TECHNICAL SPECIFICATIONS

Table 7: Technical specifications

Power supply

11.5 .. 13.5 V DC 90 .. 264 V AC, 50/60 Hz

Fuse

4 A (T-slow), 250 V

Max. power consumption

1.5 W

Load voltage

Same as power supply voltage

Maximum load current * (resistive load)

4 A AC/DC

Connection type

Screw type connectors for stranded wire 0.75 to 2.5 mm2

RF communication interval

Minimum 0.5 s

Dimensions (L x W x H)

53 x 38 x 25 mm

Weight

50 g

Ambient temperature

0 .. 40°C

Ambient humidity

Max. 95 %, no condensation

Maximum altitude

2000 m

Mounting position

Any

Transport and storage temperature -20 to 60 °C

Pollution degree

Over voltage category

Electrical equipment

Class II (double insulation)

Protection class

IP 10

* NOTE: Special care must be taken in case of usage inductive character loads, e.g. contactors, solenoids, or loads that draw high inrush currents, e.g. capacitive character load, incandescent lamps. Inductive character loads cause over-voltage spikes at output relay contacts when they are switched off. The use of appropriate suppression circuits is advised.
Loads that draw high inrush currents may cause the relay output to be temporarily overloaded with the current above its allowed limits, which may damage the output, even though that steady-state current is within the allowed limits. For that type of load, the use of an appropriate inrush current limiter is advised.
Inductive or capacitive loads influence the relay contacts by shortening their working life period or can even permanently melt contacts together. Consider using another type of digital output (e.g. triac).

Longo Bluetooth Products LBT-1.DO1
8.MODULE LABELING
Figure 10: Label
Label (sample):
XXX-N.ZZZ.UUU
P/N: AAABBBCCDDDEEE S/N: SSS-RR-YYXXXXXXXXX D/C: WW/YY
Label description: 1. XXX-N.ZZZ – full product name, · XXX-N – product family, · ZZZ.UUU product, 2. P/N: AAABBBCCDDDEEE – part number, · AAA – general code for product family, · BBB – short product name, · CCDDD – sequence code, · CC the year of code opening, · DDD – derivation code, · EEE version code (reserved for future HW and/or SW firmware upgrades), 3. S/N: SSS-RR-YYXXXXXXXXX – serial number, · SSS short product name, · RR user code (test procedure, e.g. Smarteh person xxx), · YY year, · XXXXXXXXX current stack number, 4. D/C: WW/YY – date code, · WW week and, · YY the year of production.
Optional: · MAC, · Symbols, · WAMP, · Other.
17

Longo Bluetooth Products LBT-1.DO1

9. CHANGES
The following table describes all the changes to the document.

Date
26.05.23 05.05.23

V. Description

Reviewed text, fuse and relay specifications.

The initial version, issued as LBT-1.DO1 relay output module User

Manual.

Longo Bluetooth Products LBT-1.DO1
10. NOTES
19