SMS44DW01T Dishwasher
Product Information
The product being referred to in the user manual is a
dishwasher. It is a convenient and efficient appliance for cleaning
tableware. The manual provides information on water hardness
settings, special salt usage, rinse aid usage, detergent usage,
program data, and maintenance instructions.
Water Hardness Settings
The dishwasher has a water softening system that can be adjusted
based on the hardness of the water supply. The manual provides a
table with different water hardness ranges and their corresponding
setting values. Users can select the appropriate setting based on
the water hardness in their area.
Special Salt Usage
To prevent damage to the dishwasher, special salt needs to be
added to the dispenser before starting a program. The manual
provides step-by-step instructions on how to add the special salt,
including unscrewing the dispenser lid, filling it with water, and
setting the desired water hardness value using the program
buttons.
Rinse Aid Usage
Rinse aid is another additive that enhances the performance of
the dishwasher. The manual explains how to add rinse aid to the
dispenser, including pressing the catch on the dispenser lid,
filling it up to the max mark, and closing the lid securely.
Detergent Usage
The manual instructs users to add detergent to the designated
detergent dispenser in the dishwasher. It provides specific
measurements for different types of detergents and emphasizes the
importance of closing the lid properly.
Program Data
The manual includes a table with program data measured according
to European standard EN 60436. This data includes the duration of
each program, energy consumption in kWh, and water consumption in
liters. It also mentions that these figures may vary depending on
the selected program and additional functions, as well as the use
of rinse aid.
Product Usage Instructions
- Load the tableware into the dishwasher, ensuring it is suitable
for dishwasher use and removing large food remnants. - Add the appropriate amount of detergent to the dry detergent
dispenser. - Switch on the dishwasher.
- Select the desired program.
- Start the program.
- At the end of the program, remove the clean tableware from the
dishwasher. - To cancel a program, press and hold the cancel button for
approximately 3 seconds. The program will be cancelled and end
after about 1 minute. - After each wash, check the filters for residue.
- To clean the filters, turn the coarse filter anticlockwise and
remove it. Pull down the micro filter to remove it. Clean the
filter elements under running water. Reassemble the filter system
and insert it back into the dishwasher. - Clean the spray arms by unscrewing the upper spray arm and
pulling it down. Rinse it under running water and reattach it.
Quick reference guideDishwasher
en
Short and handy…
Overview of water hardness settings
Setting water softening system Programs
… everything your dishwasher needs. Before using for the first time, make sure you read both the operating and the installation instructions.
You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.
Hardness range
Soft Soft
mmol/l
0 – 1.1 1.2 – 1.4
Setting value
H00 H01
Medium Medium Medium Hard Hard Hard
1.5 – 1.8 1.9 – 2.1 2.2 – 2.9 3.0 – 3.7 3.8 – 5.4 5.5 – 8.9
h.
min.
Adding special salt To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts. 1. Unscrew the lid of the dispenser for special salt
and remove. 2. On initial start-up: Fill the dispenser right up with
water.
H02
1. Press .
H03
2. Hold programme button A and press
H04
repeatedly until the display
H05
shows H:xx.
H06 H07
3. Release programme button A and .
a Programme button A flashes.
4. Press programme button C re-
peatedly until the right water hard-
ness has been set.
5. Press
to save the setting.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.
The program data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the program and additional function selected. The runtime will change if the rinse aid system is switched off or rinse aid needs to be added.
Program
/
Intensive 70°
/
Eco 50°
/
Quick 65°
/
Quick 45° 1 half standard load
1) Duration [h:min] 2) Energy [kWh] 3) Water [l] 1) 2:15 2) 1,500 3) 9,5 1) 4:55 2) 0,836 3) 9,5 1) 1:00 2) 1,300 3) 11 1) 0:29 1 2) 0,800 3) 10
Adding rinse aid
1. Press the catch on the lid of the dispenser for rinse aid and lift .
2. Add rinse aid up to the
2
max mark.
max
1
3. Close the lid of the dispenser for rinse aid. a The lid clicks into position.
Adding detergent 1. Add the detergent to the
dry detergent dispenser.
50 ml 25 ml
2. Close the lid of the detergent dispenser.
15 ml
a The lid clicks into position.
9001645609(020403)SMS44DW01T
*9001645609*
How to use your appliance
1. Load the tableware.
tate freely.
Only clean tableware that is suitable for dish-
2. Add detergent.
washers. Remove large remnants of food from 3. Switch on the appliance .
the tableware. Check that the spray arms can ro-
4. Select the programme. 5. Start the programme . 6. Remove the tableware at the end of the pro-
gramme.
7. To cancel the programme, press
for
approx. 3 seconds.
The programme is cancelled and ends after ap-
prox. 1 minute.
Cleaning filters
1. After each wash check the filters for
residue.
2. Turn the coarse filter anticlock-
2
wise and re-
move the filter
system .
1
3. Pull down the micro filter to remove.
4. Press the locking
catches to-
gether and lift
1
the coarse filter
out .
Cleaning spray arms
1. Unscrew the upper spray arm and
2
pull down to remove .
1
2
5. Clean the filter elements under running water.
6. Re-assemble the filter system. 7. Insert the filter system into the appliance
and turn the coarse filter clockwise. Make sure that the arrow markings match up.
2. Pull up the lower spray arm to remove.
3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
4. Insert the lower spray arm. a The spray arm clicks into position. 5. Insert the upper spray arm and screw it firmly in place.
Clean wastewater pump
1. Disconnect the appliance from the power supply. 2. Remove the filter system. 3. Scoop out any water. 4. Prise off the pump cover using a
spoon and grip it by the crosspiece.
5. Lift the pump cover inwards at an angle and remove.
6. Remove any remnants of food and foreign bodies in the area
of the impeller.
7. Insert the pump cover and press
down .
2
a The pump cover clicks into position.
1
8. Install the filter system.
Troubleshooting
Fault
Cause and troubleshooting
E:18 or indicator for water Supply hose is kinked.
supply lights up.
Install the supply hose without kinks.
Water tap is turned off. Turn on the water tap.
Water tap is jammed or furred up. Turn on the water tap.
The flow rate must be at least 10 l/min when the water supply is open.
Filter in the water supply is blocked. 1. Switch off the appliance. 2. Pull out the mains plug. 3. Turn off the water tap. 4. Unscrew the water connection. 5. Remove the filter from the sup-
ply hose
Fault E:22 lights up. E:25 lights up.
Remnants of food on tableware.
6. Clean the filter. 7. Re-insert the filter in the supply hose. 8. Screw the water connection back on. 9. Check the water connection for leaks. 10.Restore the power supply. 11.Switch the appliance on.
Cause and troubleshooting Filters are soiled or blocked. Clean the filters. Wastewater pump is blocked. Clean the wastewater pump. Cover of the wastewater pump is loose Secure the cover of the Wastewater pump so it clicks into
position. Tableware is placed too close together or basket is overfilled. 1. Arrange tableware with sufficient space in between.
The spray jets must reach the surfaces of the tableware. 2. Avoid points of contact.
Spray arm rotation is blocked. Arrange tableware so that it does not obstruct spray arm ro-
tation. Spray arm nozzles are blocked. Clean the Spray arms. Filters are soiled. Clean the filters. Filters are inserted incorrectly and/or not engaged. 1. Insert the filters properly. 2. Engage the filters.
Washing programme selected too weak. Select a more intensive washing programme.
Fault
Cause and troubleshooting
Removable streaks are Amount of rinse aid to be dispensed is set too high.
present on glasses, glass- Set the rinse aid system to a lower setting.
ware with a metallic appearance and cutlery.
No rinse aid has been added. Add rinse aid.
Rust spots on cutlery.
Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected. Use rust-resistant tableware.
Cutlery may also rust if washed together with rusting items. Do not wash rusting items.
Detergent residue is present in the detergent dispenser or the tablet collecting tray.
Spray arms were blocked by tableware so detergent was not rinsed out. Check that the spray arms are not blocked and can rotate
freely.
