BR-2B65U 2021+ Ford Bronco 2 Door Speaker
Product Information:
- Product Name: BR-2B65U
- Manufacturer: SSV Works
- Address: 201 N. Rice Ave Unit A, Oxnard, CA 93030
- Website: www.SSVworks.com
- Phone: 818-991-1778
- Fax: 866-293-6751
Tools Needed for Installation:
- None mentioned in the manual
Parts List:
- Passenger Rear Door Pod
- Driver Rear Door Pod
- Bracket Pack
- (x2) M6 x Screw
- (x2) M6 Washer
- (x2) #1 Phillips Screw
Product Usage Instructions:
- Step A: Remove the screw located at the bottom
of the speaker enclosure. - Step B: Remove the two screws securing the
bracket to the vehicle. Then remove the two screws securing the
bracket to the enclosure. - Step A: Secure the driver’s side bracket to
the driver’s side pod using the factory two screws. - Step B: Hold the pod up near its mounting
location and connect the factory harness. - Step C: Snap the speaker pod harness cover
onto the pod making sure the harness exits the cover through one of
the two reliefs. - Step D: Use the provided Philips screw to
secure the cover in place. - Step E: Loosely assemble the bottom of the pod
to the frame of the vehicle using the provided M6 screw and
washer. - Step F: Install the two factory bolts securing
the pod to the vehicle. - Step G: Fully tighten the bottom screw located
at the bottom of the pod.
Repeat all steps for the opposite side.
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
· T25, T30 Torx Driver · #1 Phillips Screwdriver
PARTS LIST IMAGES
BR-2B65U
2021+ Ford Bronco, 2 Door 6.5″ Rear Speaker-Pod Add-Ons
Please read and understand these
!
instructions completely before installation to avoid possible injury, or damage to the
accessory or vehicle.
Passenger Rear Door Pod
Driver Rear Door Pod
Bracket Pack
(x2) M6 x Screw
(x2) M6 Washer
(x2) #1 Phillips Screw
BR-2B65U
2023 SSV Works, Oxnard, Ca 93030
BR-2BR65 Rev. A. 4-24-23
A
A. Remove the screw located at the bottom of the speaker enclosure.
B
B. Removing the two screws securing the bracket to the vehicle. Then remove the two screws securing the bracket to the enclosure.
Note: These 4 factory screws will be re-used for the SSV pods. *This image is of passenger side .
A
A. Secure the drivers side bracket to the driver side pod using the factory two screws.
B
B. Hold the pod up near its mounting location and connect the factory harness.
C
C. Snap the speaker pod harness cover onto the pod making sure the harness exits the cover through one of the two reliefs.
D
D. Use the provided Philips screw to secure the cover in place. E. Loosely assemble the bottom of the pod to the frame of the vehicle using the provided M6 screw and washer.
BR-2B65U
2023 SSV Works, Oxnard, Ca 93030
BR-2BR65 Rev. A. 4-24-23
E
E. Loosely assemble the bottom of the pod to the frame of the vehicle using the provided M6 screw and washer.
F
F. Install the two-factory bolts securing the pod to the vehicle. Note: Image is of passenger side.
G
G. Fully tighten the bottom screw located at the bottom of the pod.
Repeat all steps for the opposite side.
BR-2B65U
2023 SSV Works, Oxnard, Ca 93030
BR-2BR65 Rev. A. 4-24-23
SSV Works
