Daktronics Gs6 Galaxy Displays Instructions

Gs6 Galaxy Displays

PIXELS HIGH (AAA)
360 288 216

OVERALL DISPLAY SIZE GS6-AAAxBBB-CC

PIXELS WIDE (BBB)
425

PIXEL SPACING (CC)
15.85mm

340

19.81mm

255

26.42mm

9′ 7-7/16″ [2931] OVERALL TOP SECTION

9′ 7-7/16″ [2931] OVERALL BTM SECTION

SEE INSTALL NOTE #11.

LIGHT SENSOR (DO NOT BLOCK)

2″ [51] MTG HOLE SPACING @2

4″ [102] DETAIL A
SCALE 1/18

SEE DETAIL A
EXHAUST VENTS, SEE VENTILATION NOTES #1, AND #2.
19′ 2-13/16″ [5863]

SIGNAL INTERCONNECT SEE INSTALL NOTE #10.
10′ 10-15/16″ [3325]

SIGNAL INTERCONNECT SEE INSTALL NOTE #10.
1′ 6-9/16″ [472] 0″ [0] INTAKE VENTS, SEE VENTILATION NOTES
#1, AND #2.

0″ [0] 1′ [305] 2′ 10-5/16″ [871] 6″ MAX 11′ 4-5/16″ [3462] 6″ MAX 18′ 6-13/16″ [5659] 19′ 10-5/16″ [6053] 6″ MAX 21′ 8-1/2″ [6616] 22′ 7-3/8″ [6893]

SECTION 101 GS6-AAAxBBB-CC

PIXELS HIGH (AAA)
180
144
108

PIXELS WIDE (BBB)
425
340
255

PIXEL SPACING (CC)
15.85mm
19.81mm
26.42mm

SECTION 201 GS6-AAAxBBB-CC

PIXELS HIGH (AAA)
180

PIXELS WIDE (BBB)
425

PIXEL SPACING (CC)
15.85mm

144

340

19.81mm

108

255

26.42mm

DAKTRONICS
22′ 1-3/16″ [6736] ACTIVE WIDTH 22′ 7-3/8″ [6893] OVERALL WIDTH
FRONT VIEW

2-1/4″ [57]

USE A GALVANIZED OR WEATHER PROTECTED 5/8″ BOLT (MIN ASTM A325), WASHERS (MIN ASTM F436), AND NUT (MIN ASTM A563) OR WELD. SEE WELD SPECIFICATIONS ON DETAIL D.

18′ 8-5/8″ [5706] ACTIVE HEIGHT
19′ 2-13/16″ [5863] OVERALL HEIGHT

3 SIDES 1/4″

1″ [25] TYPICAL FOR ALL T-CLIPS

DETAIL C
SCALE 1/18

2-1/4″ [57] SEE HARDWARE SPECIFICATIONS ON DETAIL C

3 SIDES 1/4″
ALL WELDING SHALL BE PERFORMED BY A WELDER
CERTIFIED FOR THE SPECIFIED TYPE AND POSITION DETAIL D
OF THE REQUIRED WELD. ALL WELDING SHALL BE SCALE 1/18 IN ACCORDANCE WITH AWS 01.1. SHIELDED METAL
ARC WELDING PROCESSES SHALL BE USED TO PERFORM WELDS WITH A LOW HYDROGEN E70 SERIES
ELECTRODE.
SEE INSTALL NOTE #11

14′ 3-5/8″ [4359] DISTANCE BETWEEN LIFTLUGS. SEE INSTALL NOTES #1, #2, AND #3.

PORTIONS OF TOP BORDER COVERS ARE REMOVED. FOR CLARIFICATION SEE INSTALL NOTE #4.
MILL FINISH ALUMINUM REAR OF DISPLAY SEE INSTALL NOTE #9.
SIGNAL INTERCONNECT SEE INSTALL NOTE #10.
11′ 2-1/8″ [3407] SEE DETAIL B
POWER ENTRANCE SEE INSTALL NOTE #6. PRIMARY SIGNAL INPUT QUICK CONNECT. SEE INSTALL NOTE #7.
1′ 11-7/8″ [606] 1′ 9-13/16″ [554] OPTIONAL SIGNAL ENTRANCE SEE INSTALL NOTE #8. GROUND LUG. SEE INSTALL NOTE #5.

8″ [203] 2″ [51] MTG HOLE SPACING @3

DETAIL B
SCALE 1/18

SEE DETAIL C 18′ 10-1/4″ [5746]

1′ 4-5/16″ [415]

9′ 7-3/16″ [2925] SEE DETAIL D

T-CLIPS. SEE DETAILED VIEWS C & D. SEE INSTALL
NOTE #11.

4-1/16″ [104] 0″ [0] TOP OF STEEL DIMENSIONS

2-1/4″ [57] CLEARANCE NEEDED FOR QUICK CONNECTS
11-1/16″ [282]

LEFT SIDE VIEW

REAR VIEW

REV

DATE:

BY:

#

DETAIL

DESCRIPTION

1 DISPLAY

GS6-AAAxBBB-CC (SEE CHART IN TOP LEFT CORNER)

2

LED COLOR

RGB / RED / AMBER

3 ACTIVE AREA 18′ 8-5/8″ [5706] X 22′ 1-3/16″ [6736]

4 OVERALL SIZE 19′ 2-13/16″ [5863] X 22′ 7-3/8″ [6893]

5 CABINET

ALUMINUM & STEEL

6 VENTILATION REAR INTAKE & EXHAUST

7 ACCESS 8 WEIGHT 9 SHIPPING

SERVICE FROM FRONT OF DISPLAY
SECTION 101: 2415 LBS [1095 KG] (APPROX) SECTION 201: 2415 LBS [1095 KG] (APPROX) TOTAL: 4830 LBS [2191 KG] (APPROX)
SHIPPED IN TWO SECTIONS. ASSEMBLY OF SECTIONS IS REQUIRED ON-SITE

10 DIMENSIONS FEET AND INCHES [MILLIMETERS]

STRUCTURAL RATING

1

DESIGN WIND PRESSURE “P” (CASE A)

2 STANDARD/CODE

3 MINIMUM STRINGER DIMENSION

P<=100 PSF
SEE DD4145274 FOR APPLICABLE DESIGN CODE
HSS 4″ X 4″ X 3/16″

4 MAXIMUM CLIP ANGLE SPACING

9′ 6″ [2896] 1′ MAX

POWER RATING PER SINGLE FACE: FOR SIZING ELEC.SERVICE MAX REQ’D SHOWN

MOD GRID

SECT.

COLOR

MAX WATTS

120/240VAC 1PH 60Hz (3 WIRES + GND) DOMESTIC

LINE 1 AMPS

LINE 2 AMPS

240VAC 1PH 50Hz (2 WIRES + GND) INTERNATIONAL SPECIAL ORDER
LINE 1 (AMPS)

RGB 7142 9 X 17 101
MONO 3863

29.17 17.03

30.38 15.20

29.76 16.10

RGB 7142 9 X 17 201
MONO 3863

29.17 17.03

30.38 15.20

29.76 16.10

RGB 14284 18 X 17 TOTAL
MONO 7726 VENTILATION REQUIREMENTS

58.34 34.06

60.76 30.40

59.52 32.20

DISPLAY RELIES ON VENTILATION TO FUNCTION PROPERLY.

1

VENTILATION HOODS, LOCATED AT THE BACK OF THE DISPLAY, MUST BE ABLE TO DRAW IN AIR AT A TEMPERATURE NO

GREATER THAN 120°F

AIRFLOW AT AMBIENT TEMPERATURE CAN BE MAINTAINED BY PROVIDING

OPENINGS FOR INTAKE (AT THE BOTTOM) AND EXHAUST (AT THE TOP)

BEHIND THE DISPLAY. A MINIMUM OF 12.0 SQFT FOR INTAKE AND

2

12.0 SQFT FOR EXHAUST IS REQUIRED. IF THE OPENINGS CANNOT

BE PROVIDED AS STATED, USE WALL MOUNT PROPELLER FANS TO

GENERATE A MINIMUM OF 3600 CFM OF AIRFLOW ACROSS THE BACK

OF THE DISPLAY.

INSTALL NOTES

1

WHEN LIFTING USE ALL LIFTLUGS AND MAINTAIN AN ANGLE LARGER THAN 55° BETWEEN THE CABINET AND LIFTING DEVICE.

1-1/16″ LIFTLUG DIAMETER TO ASSIST WITH DISPLAY

2

INSTALLATION. MAX WIND SPEED DURING INSTALLATION

MUST BE LESS THAN 20 MPH.

3

LIFTLUGS MAY NOT BE USED FOR PERMANENT INSTALLATION.

DISPLAY WILL BE SHIPPED WITH SOME TOP BORDER COVERS 4 REMOVED. COVERS WILL NEED TO BE ATTACHED WITH INCLUDED
HARDWARE AFTER DISPLAY IS MOUNTED TO STRUCTURE.

5

GROUND LUG FOR GROUND CONNECTION. ALL SECTIONS NEED TO BE GROUNDED.

6

2″ MEYERS HUB FOR POWER TERMINATION TO INTERNAL LOAD CENTER. SEE POWER RATINGS ABOVE.

7

SIGNAL INPUT AT QUICK CONNECT. PRIMARY/SINGLE FACE DISPLAY SHOWN. SEE CLEARANCE DIMENSION ON LEFT SIDE VIEW.

8 TWO 1/2″ CONDUIT KNOCKOUTS FOR OPTIONAL SIGNAL ENTRANCE.

9

DISPLAY WILL BE PAINTED SEMI-GLOSS BLACK ON FRONT AND SIDE PERIMETER WITH MILL FINISH ALUMINUM ON REAR OF DISPLAY.

10 MECHANICAL AND SIGNAL CONNECTIONS OCCUR EXTERNAL TO DISPLAY.

T-CLIPS FOR MOUNTING.T-CLIPS CAN BE ADJUSTED VERTICALLY

11

1/2″ AS NEEDED DURING INSTALLATION. T-CLIPS CAN BE WELDED OR BOLTED TO STRINGER AT A MAX DISTANCE 2-1/2″.

SEE DETAILS C & D.

12

DAKTRONICS IS NOT RESPONSIBLE FOR THE MOUNTING HARDWARE OR THE INTEGRITY OF THE MOUNTING STRUCTURE.

13

DAKTRONICS IS NOT RESPONSIBLE FOR THE MAIN ELECTRICAL DISCONNECT. SEE POWER RATINGS ABOVE.

14

FOR MORE INSTALLATION DETAILS AND GUIDELINES REQUEST DD-1954173 FROM YOUR DAKTRONICS REPRESENTATIVE

THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA)

THIRD ANGLE PROJECTION

PROJECT: GS6 GALAXY DISPLAYS

TITLE: SHOP DWG, GS6-R, 19′ 3”x22′ 8” (18×17 MODS)

DATE: 10-MAR-23

DIM UNITS: INCHES [MILLIMETERS] SHEET REV

SCALE: 1/90

DO NOT SCALE DRAWING

1 OF 1 00

DESIGN: TWHITEH DRAWN: MLEOPOL

JOB NO.
P1874

FUNC – TYPE – SIZE
E – 07 – B

5226205