Sealey Ht301r Rechargeable Head Torch Instruction Manual

1. Fit the torch to the head set using the washer, thumb-wheel,
   cover, and screw. Adjust the orientation of the torch to suit.
2. To turn on the light at full power, press the power button
   once. Press it again to dim the light, and press a third time to
   turn off the light.

1. Remove the USB socket cover on the torch.
2. Connect the USB lead to the port on the end of the battery pack
   and the

2.5W SMD LED RECHARGEABLE HEAD TORCH MODEL NO: HT301R
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to instructions

1. SAFETY

9

Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. If worn or

damaged DO NOT use.

9

Ensure the torch is fully charged before initial use.

8

DO NOT charge in damp conditions.

8

DO NOT turn the torch on when it is being charged.

8

DO NOT shine directly into your, another person’s or an animal’s eyes.

8

DO NOT allow children to use the torch.

8

DO NOT handle or move the torch whilst it is being charged.

8

DO NOT use the torch if you suspect that the battery or the torch casing is damaged.

8

DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently

recharge the battery at least once every six months of non-use.

8

DO NOT attempt to open, disassemble, modify or service the battery pack.

8

DO NOT crush, puncture, short external contacts or dispose of in fire or water.

9

Replace only with the battery pack designated for this product.

9

Recycle or dispose of used battery as stipulated by local regulation.

9

If the electrolyte in the cells gets on your skin, thoroughly rinse with water. If it gets in your eyes, rinse thoroughly with cool water and

seek immediate medical attention.

2. INTRODUCTION

Hands-free 2.5W SMD LED head torch to direct light as required. Two power settings – high and 60% power with an output of 250/150lm. Green LED charge indicator. Extendable arms with foam pads for added comfort. Supplied with Type-C USB charging cable.

3. SPECIFICATION

Model No:………………………………………………………..HT301R Battery: ………………………………………. 3.7V 1.6Ah Lithium-ion Charging Time:………………………………………………………3.5hr LED Type: ……………………………………………………. 2.5W SMD Lumen Output: ………………………………..High/Low: 250/150lm Operating Time: …………………………………… High/Low 2/3.5hr

4. OPERATION

Charge Port On

4.1.

Fit the torch to the head set using the washer, thumb-wheel, cover and

Rear Face

screw. Adjust the orientation of the torch to suit.

4.2.

Pressing the power button once will turn the light on full power, pressing

it again will dim the light and pressing a third time will turn the light off.

4.3.

CHARGING

NOTE: The torch can also be detached from the collar which may make

Charge

charging more convenient.

Indicator

4.3.1. Remove USB socket cover on the torch.

4.3.2. Connect the USB lead to the port on the end of the battery pack and the

other end to a USB power socket. Turn on the power supply.

4.3.3. Switch off power supply, remove charging lead and replace socket cover

on battery pack.

4.3.4. The charge indicator (green LED) on the side of the torch will flash to show the unit is charging and has charge.

© Jack Sealey Limited

Original Language Version

HT301R Issue 2 (2) 24/04/2023

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500

[email protected]

www.sealey.co.uk

© Jack Sealey Limited

Original Language Version

HT301R Issue 2 (2) 24/04/2023