GFD65GSSVWW Reversible Side Swing Door Stackable Steam Cycle Smart Gas Dryer
Product Information
The product model numbers are GFD65GSSVWW and GFD65GSPVDS. The
product is a gas dryer with a rating of 120V, 60Hz, and 8A. The
dimensions of the dryer are as follows:
- Stacked: 46-3/4″ (H) x 28″ (W) x 32″ (D)
- Riser: 55-7/8″ (H) x 28″ (W) x 32″ (D)
- Pedestal: 79-1/2″ (H) x 28″ (W) x 32″ (D)
The dryer is ADA compliant and comes with leveling legs that can
be retracted or fully extended.
Special Installation Requirements
For stacked installation, brackets for stacking the dryer over a
washer are not included with the washer. The part number for the
stacking kit is GFA28KITN.
If installing in an alcove or closet, the dryer must be
exhausted to the outside. Minimum clearances between the dryer
cabinet and adjacent walls or surfaces are 0 on all sides and top.
Closet doors must be louvered or ventilated, with a minimum of 60
sq. in. of open area equally distributed. If the closet contains
both a washer and a dryer, doors must have a minimum of 120 sq. in.
of open area equally distributed. No other fuel-burning appliance
should be installed in the same closet as the gas dryer.
If installing in a bathroom or bedroom, the dryer must also be
exhausted to the outdoors. The installation must conform to local
codes or, in the absence of local codes, to the National Electric
Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
For installations other than alcove or closet installations,
minimum clearances to combustible surfaces are 0 on all sides and
top.
Exhaust Length Calculation
The maximum length of 4″ rigid (aluminum or galvanized) duct
that can be tolerated is shown in a table. The dryer must be
exhausted to the outside. It is important not to terminate the
exhaust into a chimney, under any enclosed house floor (crawl
space), or into an attic to avoid fire hazards or moisture damage.
The exhaust should be terminated in a dampered wall cap located at
least 12″ above the ground or any obstruction, with the opening
pointed down to prevent back drafts, bird nesting, etc.
Product Usage Instructions
1. Make sure the dryer is properly installed according to the
installation instructions provided with the product.
2. If stacking the dryer over a washer, ensure that the
appropriate stacking kit (part no. GFA28KITN) is used.
3. If installing in an alcove or closet, make sure the dryer is
exhausted to the outside. Ensure that there are minimum clearances
of 0 on all sides and top between the dryer cabinet and adjacent
walls or surfaces. If the closet contains both a washer and a
dryer, make sure the doors have a minimum of 120 sq. in. of open
area equally distributed.
4. If installing in a bathroom or bedroom, ensure that the dryer
is also exhausted to the outdoors. Follow local codes or, in the
absence of local codes, the National Electric Code and National
Fuel Gas Code, ANSI Z223 for gas dryers.
5. For installations other than alcove or closet installations,
ensure minimum clearances of 0 on all sides and top to combustible
surfaces.
6. Use the appropriate accessories for the dryer if required.
Refer to the list of dryer accessories provided in the user
manual.
7. For improved performance, it is suggested to have a 1/2″
clearance on each side of the dryer.
8. Regularly clean the lint filter to prevent lint buildup and
maintain dryer efficiency.
9. Follow the maintenance instructions provided in the user
manual to keep the dryer in optimal condition.
10. If any issues or concerns arise during usage, refer to the
troubleshooting section of the user manual or contact customer
support at 1-800-GE-CARES.
GFD65GSSVWW / GFD65GSPVDS
GE® 7.8 cu. ft. Capacity Front Load Gas Dryer with Steam
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
Stacked:
GAS DRYER RATING 120V 60Hz, 8A
EXHAUST OPTIONS: 4-way via rear, left, right, and bottom. (The right, left, and bottom venting options require Side Vent Kit: GFA28DSVN) CIRCUIT REQUIREMENTS: An individual, properly grounded branch circuit, protected by a 15-20 amp circuit breaker or a time-delay fuse, is required. NOTE: Dryer wall outlet must be located within 36″ of service cord entry and accessible when dryer is mounted in position. INSTALLATION INFORMATION: For complete information, see installation instructions packed with your dryer.
Riser:
Pedestal:
46-3/4
(118.7 cm)
16 7
ADA Compliant
55-7/8
(141.8 cm)
79-1/2
(202 cm)
28
(71.2 cm)
32″
(81.28 cm)
54-1/4″
(137.8 cm)
*With leveling legs retracted: 39-3/4″ (101 cm).
With leveling legs fully extended: 40-5/8″ (103.1 cm).
*39-3/4
(101 cm)
Front View
Side View
For answers to your Monogram, CaféTM, GE ProfileTM or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
22-7/8″
(58.1 cm)
6-1/8″
1-5/8″ 11″
Back View
3-5/8″
Specification Revised 6/23
GFD65GSSVWW / GFD65GSPVDS
GE® 7.8 cu. ft. Capacity Front Load Gas Dryer with Steam
SPECIAL INSTALLATION REQUIREMENTS:
STACKED INSTALLATION: Brackets for stacking dryer over washer are not included with the washer. Order part no. GFA28KITN.
ALCOVE OR CLOSET INSTALLATION: If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0″ all sides and top.*
Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION: The dryer MUST be exhausted to the outdoors.
The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATIONS: Minimum clearances to combustible surfaces 0″ all sides and top.*
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE-CARES.
*For improved performance, a 1/2″ clearance is suggested on each side. **Accessories sold separately.
WEIGHT -Carton weight 147 lbs. -Product weight 137 lbs.
DRYER ACCESSORIES**
GE Part Number Description
WE25M87
LP Conversion Kit
WB64X5025
Touch-up Paint (White) .06 oz.
WR97X27706 Touch-Up Paint (Carbon Graphite) 0.6 oz
WE02X29449 Dryer Rack Accessory
GFA28DSVN
Side Vent Kit
WH41X10207
Inlet Hose
WX17X10001CA Vibration Pads
GFP1528SNWW Pedestal Accessory (White)
GFP1528PTDS Pedestal Accessory (Carbon Graphite)
GFR0728SNWW Riser (White)
GFR0728PTDS Riser (Carbon Graphite)
GFA28KITN
Stacking Kit
WARRANTY Labor Warranty Parts Warranty
Limited 1-year entire appliance Limited 1-year entire appliance
For answers to your Monogram, CaféTM, GE ProfileTM or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Specification Revised 6/23
GFD65GSSVWW / GFD65GSPVDS
GE® 7.8 cu. ft. Capacity Front Load Gas Dryer with Steam
DRYER EXHAUSTING INFORMATION METAL DUCT ONLY
For complete information, see installation instructions packed with your dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with 4″ diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE-CARES.
A A
4 B
Domestic 2-1/2 dryer models
7.5 cu. ft. capacity models electric dryers
Best performance
Maximum length of 4″ dia. rigid metal duct
Exhaust hood type
Number of 90°
turns
0 1 2 3 4
A 4″ opening
90 ft. 60 ft. 45 ft. 35 ft. 25 ft.
B 2 -1/2″ opening
60 ft. 45 ft. 35 ft. 25 ft. 15 ft.
6-1/8
1-5/8 11
55″ long Power Cord
3-5/8
Dryer Vent
For answers to your Monogram, CaféTM, GE ProfileTM or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Specification Revised 6/23
GFD65GSSVWW / GFD65GSPVDS
GE® 7.8 cu. ft. Capacity Front Load Gas Dryer with Steam
FEATURES AND BENEFITS
Powersteam Refresh small loads and dewrinkle larger loads with the power of steam.
Built-in WiFi Start, stop and monitor your laundry from anywhere while receiving real-time notifications and updates.
Quick Dry Quickly dries items and small loads for families on the go.
Reduce Static Prevents static cling with a gentle mist near the end of the cycle.
Sanitize Cycle Sterilize clothing with elevated temperatures designed to kill common household bacteria.
Wrinkle Care Prevents wrinkles by extending the tumble without heat.
Damp Alert Signals when delicate clothes reach the ideal dampness level for ironing or final air drying.
Vent Sensor Provides alerts when a restriction is detected in your dryer vent.
4 Way Venting Easy-to-change venting options provide the ultimate installation flexibility to fit in your home.
Reversible Door Easily reverse your washer and dryer door for superior installation flexibility.
Shallow Depth Never compromise on convenience with this 32″ shallow depth unit that easily fits into tight spaces like an alcove or closet, making it a suitable solution for homes of any size.
My Settings Store preferred dry cycle settings for later use, maximize time and alleviate adjusting cycle preferences with every load.
Model GFD65GSSVWW White Model GFD65GSPVDS Carbon Graphite
4-way Venting Option
For answers to your Monogram, CaféTM, GE ProfileTM or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Specification Revised 6/23
GE Appliances: Shop for Home, Kitchen, & Laundry Appliances
